SOURCE: where do you add transmission fluid for a 2002 pt cruiser
through the tube is measured where the oil level
SOURCE: my 2002 pt cruiser won't shift out of low.
the 2nd & 3rd gear solenoid needs replacing. It is mounted by the trans filter inside the trans pan
SOURCE: location speed sensor pt cruiser 03 touring car do
It sounds like the module is in limp mode. The speed sensor is most likely the cause, but it can be some other things as well. A scan will give a code stating the problem area.
The speed sensors are on the side of the trasmission that faces the front of the vehicle. There are 2 of them, and they are the same sensor. One is an input speed sensor located closest to the engine, the other is the output speed sensor.
SOURCE: Shifting solenoids on 2002 Lancer.
For Automatic transmission
problem,click the link below:----
Automatic transmission
troubleshooting:----
http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html --------- http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html ----------- http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html -------------- AUTOMATIC TRANSMISSION FLUID AND
FILTER? http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html ----------- http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html -------- http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html -------- http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html ----------- http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html ---------- http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html ---------- http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html ------------- http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html ------------- http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html ---------- http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html ----------- This
will help. Thanks.
Automatic transmission shift lever
issues?-------
AUTOMATIC TRANSMISSION FLUID LEVEL? --
Transmission fault light on
car dash?
Transmission shifting
problem?
Transmission Slips out of 2nd gear?
OD light flashing and transmission fluid
leaking?
Why Transmission fluid leaks near radiator?
Transmission fluid leaking?
****** wont go in reverse?
Automatic transmission will not go into
reverse?
Transmission is making buzzing noise?
SOURCE: How to change light bulb on console gear shift
I have 2002 Cruiser, not sure if it's the same configuration. Here's what I did:
Remove the Console: Slide front seats all the way back and recline them all the way to get the armrests out of the way. Pull the emergency brake ALL the way up. Set the gear shift in neutral. Remove the 4 screws in the cup holders front and rear. Remove the rear window controller (pry out gently), then squeeze the tab and pull out each of the 2 connectors. I also have a 12v socket at the front of the console - squeeze the blue tab and pull gently. The console should be free and should lift straight up with a little coaxing.
Remove the Gear Shift indicator assembly: You MIGHT be able to remove the light bulb without doing this, but I couldn't. With a T10 torx screwdriver, remove the 4 screws in each corner. Lift the assembly up as far as practical (a couple inches). The bulb socket under the PRND21 indicator has 2 very small tabs on each side that no normal-sized human being can squeeze together - I pried the bulb socket out of the white 'shroud' with a screwdriver at each tab location (2).
Pull on the black socket. The socket rotates freely and is NOT the normal "turn a quarter turn and it's out" type socket. (That'd be too easy!) The bulb is a standard interior auto bulb. Replace it and reverse the procedure to reinstall. About 30 minutes for this job.
1,503 views
Usually answered in minutes!
×