Question about 1997 Ford Expedition

Open Question

What size rivet does the 1997 ford expedition window metal b pillar panel use

Posted by RODNEY Williams on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I buy a door lock actuator rivet for a 2001 ford expedition


Amazon.com: Dorman 746-157 Door Lock Actuator ...

www.amazon.com > ... > Motors > Power Door Lock

Amazon.com, Inc.
Rating: 4.5 - ‎23 reviews
Amazon.com: Dorman 746-157 Door Lock Actuator: Automotive. ... FYI. you do NOT have to drill out rivets and replace with nuts and bolts. Use a long ... My advise is to spend a little more on a different brand and buy something that works. ... works great on the 2000 Ford Expedition 5.4 V8 ... Great for 2001 F150 crew cab.

10 Ford Door Lock Actuator Peel-Type Rivet N808689-S417

www.amazon.com > ... > Interior Switches > Door Lock

Amazon.com, Inc.
Rating: 5 - ‎2 reviews
Amazon.com: 10 Ford Door Lock Actuator Peel-Type Rivet N808689-S417: Automotive. ... Verified Purchase ... For reference, I put these on my 1999 Expedition.Missing: 2001

Dec 02, 2015 | Ford Cars & Trucks

1 Answer

How do i replace left window switch on a 1997 chevrolet lumnia


the actual switch to roll your window up, or is it the window motor? window switch is easy. all you have to do is remove door panel and disconnect the connector from the switch and pop it out of the panel and install the new one. window motor, you have to remove panel and there is a metal frame on inside the door that is sometimes riveted. if that's the case, you may need to rivet it after you pop the rivets. or some make a hole around the motor specifically there to replace the motor. shouldn't be a bad job. all you have to do is get in there and see what you got. not that hard of a job.

Aug 24, 2014 | 1997 Chevrolet Lumina

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

1 Answer

How do i finish removing my window regulator on my 1997 mercury mountineer? it has some fasteners i am not familiar with.


these are big rivets you have to take a small punch and punch out the center pin looking thing ......then u can drill the rest of the rivets out and by the way u will need either this same rivet size which is one fourth inch and the rivets to put back together

Nov 15, 2010 | 1997 Mercury Mountaineer

1 Answer

On a 1998 expedition, where is the pcm and the ecm--5.4 litre


1998 Ford Truck Expedition 4WD 5.4L EFI 8cyl

PCM Ford's Location:
* Ranger - behind instrument panel (cowl), center to both driver and passenger sides.
* Explorer/Mountaineer - behind instrument panel (cowl), (access from engine compartment dash panel) on passenger side to center of vehicle.
* All other F-Series, Expedition/Navigator - lower dash panel on passenger side.
* Excursion - lower dash panel on driver side.

The PCM is behind the glove box and has a big harness connector in the firewall that you access from the engine compartment.

REMOVAL & INSTALLATION

a927c58.jpg

Fig. 1 The calibration number will be needed to order such parts as a replacement PCM, various sensors, and almost any emission control component. Typically this number is attached to a label found on the driver's door or the door pillar


1997-00 F-150, F-250, Expedition and Navigator

00a02b5.jpg

Fig. 2 Loosen the connector retaining bolt and remove the PCM connector

2cda058.jpg

Fig. 3 Remove the passenger side front door scuff plate

1fe310f.jpg

Fig. 4 Remove the passenger side kick panel

234c3f5.jpg

Fig. 5 Remove the PCM bracket clip and remove the PCM
  1. Remove the battery and the battery tray.
  2. Loosen the connector retaining bolt and remove the PCM connector.
  3. Remove the passenger side front door scuff plate.
  4. Remove the passenger side kick panel.
  5. Remove the PCM bracket clip.
  6. Remove the PCM.
To install:
  1. Installation is the reverse of removal.
  2. Tighten the PCM connector retaining bolt to 36-44 inch lbs. (4-5 Nm).

Hope helps.

Jul 13, 2010 | Ford Expedition Cars & Trucks

1 Answer

Firing order 1997 ford expedition


1997 Ford Expedition 2WD - 5.4 liter SOHC V-8 VIN "L"

f1e04b3.gif


1997 Ford Expedition 4WD - 4.6 liter V-8 VIN "6"

0d5055f.gif

Other engine sizes can find in Firing Order

Hope helped, remember rated this help. Good luck.

Dec 09, 2009 | 1997 Ford Expedition

1 Answer

HOW TO GET DOOR LOCK ACTUATOR OFF


make sure window is fully up.remove door panel.look for a rivet on the door near location of latch sometimes on the side where latch is or where door panel is.remove rivet.loosen latch and remove actuator.reinstall latch and door panel and it should work properly

Nov 05, 2009 | 1997 Ford Expedition

1 Answer

1997 ford expedition window won't go up... how do


Remove sail panel cover for mirror, remove screw. Remove window switch cover and remove screw. Remove courtesy lamp lens on door and remove screw. Remove inside door handle trim cover and remove 8mm bolt and handle. Lift upwards and remove door panel.

Oct 08, 2009 | 1997 Ford Expedition

1 Answer

Actuator removal


please rate as solved if this is what you need. You will need to borrow a heavy duty riveter from autozone or wherever you buy the lock cylinder from.


Removal
  1. NOTE: The rear door window glass must be completely raised.
    Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the rear door trim panel. For additional information, refer to Section 501-05 .
Trim Panel —Rear Door, Expedition Removal
  1. Remove the power window switchplate (14524).
  1. Disconnect the electrical connector.
  1. Remove the rear door handle trim cover.
  1. Remove the rear inside door handle.
    • Remove the door handle bolt.
  1. Remove the rear door trim panel screws at bottom of panel.
  1. s2j~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the rear door trim panel, do not pull directly outward.
    Lift upward and then outward to remove the rear door trim panel (27406).
  1. Remove the rear door watershield.
  1. Disconnect the power door lock actuator electrical connector.
  1. Drill out the power door lock actuator rivet.
9ac2386.gif
  1. Remove and discard the screws.
  1. Remove the power door lock actuator.
    • Disconnect the power door lock actuator rod.
Installation
  1. NOTE: Use new screws when installing the rear door latch.
    To install, reverse the removal procedure.
    • Use Heavy Duty Riveter to install the new rivet.

Jun 14, 2009 | 2002 Ford Expedition

Not finding what you are looking for?
1997 Ford Expedition Logo

Related Topics:

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Mike

Level 3 Expert

4369 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...