Question about Mitsubishi Montero Sport

1 Answer

How do i remove the power window motor driver door

2001 ive already rmoved the door panel

Posted by Joe montalvo on

Ad

1 Answer

Jim Akins

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 201 Answers

First this may be difficult, but here are the basics. Go buy a set of plastic tools at Harbor Freight to remove the door trim panel. It will be a combination of screws and plastic pop-in plugs that you have to pry out and you need those plastic tools not to wreck the trim panel. Label and unplug any wires holding the trim panel on. Once the trim panel is off, you should be able to see the power window motor. You are now on your own as I would have to see it to figure out how to get off. Check to see if there is a You-Tube video for your particular car. Some are good. Some of these things are easy to get off. Some are monsters. I never took one off a Mitus.

Posted on Aug 27, 2016

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear door beltline trim removal


Pull the panel around the outer periphery there are bird beak plastic retainers holding the panel to the inner door metal. You will have to give it a slight jerk with hand or purchase a tool at the local auto store to slid under the panel in the clip area. You can buy birds beak retainers at the auto store if you break them.

Dec 04, 2013 | 2000 Saturn L-Series

1 Answer

How to remove a driverside power window switch on a 2000 safari


The switch should pop out of the door panel using a flat screw
driver in on cluster that holds all the window switches. Then
you can rmove the switch you want easily. Just be gentle when
prying the cluster out of the door, and the switch out of the cluster
as not to damage the holding clips.

Jul 10, 2012 | 1997 GMC Safari

1 Answer

The handle is broken how can it be replaced. it cannot be opened


if it cant be opened from either side( child lock is on...etc) then the only way to get it open ist to try and rmove the inside door panel without breaking it< which is pretty much impossible. once you get into the door panne you can open the door by pushing the rod that used to connect to the handle. cheapest rout is to find a door panel and a door handle at a junk yard

Jan 18, 2011 | 1996 Ford Contour

1 Answer

The right side power window stopped working on my 2001 Chev. Silverado pickup. How do I get the door panel; off and how do I check the motor?


rmove all screws on door panel, and any trim. Pull firmly on bottom of panel to remove, to test the motor all you need is a test light, if you have power and ground with key on the motor is bad

Jun 10, 2010 | 2000 Chevrolet Silverado

1 Answer

Is it hard to replace hub bearing on gmc jimmy 2001


No,,,Remove the wheel,the brake caliper,unplug the abs sensor,if it is 4x4,rmove the center nut on the axle,rmove the rotor,and caliper braket,bracket first of course,then unbolt the three bolts that hold the bearing assembely,that is it.

Mar 25, 2010 | 2001 GMC Jimmy

1 Answer

How do I install a side view mirror on my F250?


The door panel must be removed to get to the wiring. On a 04 250 you need to: pop off the moulding covering the mirror mounting nuts. Pry the window switch plate forward then up to disconnect it, then unplug it . Rmove the screw behind the switch plate and behind the reflector. Push up on the door panel to remove it.

Mar 16, 2010 | 2004 Ford F150

2 Answers

Leaking heating core 2001 saturn L100


mine did same thing. It was just the o-rings on pipes where they slide into heater core simple and cheap fix. do it yourself.

Feb 19, 2010 | 2001 Saturn L-Series

2 Answers

Need to rmove passenger side mirror so nee to know how to remove trim


pull very carefully usaually held on be plastic grabber on the inside you just have to pry carefully

Oct 13, 2009 | 1997 Jeep Grand Cherokee

1 Answer

How do you remove the door panels on a 1995 mercury villager


http://autos.groups.yahoo.com/group/villagerquest/

you have to remove the cup behind the door handle. rmove screws aroun the door pull. get a screw driver and pry the trim panel away from the door carefully. There is a plastic christmas tree clip every 6 inches. when the bottom & sides are free, lift up the trim panel to get it out of the track at the base of the window.
--------------------------------------------------------------------------------------

Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).

  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screw from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connections.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
  1. Remove the front door trim panel.

Jan 04, 2009 | 1995 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...