At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
How do I put the toyota 98 model 160I Gle into program mode?
The current keyless remote does not work and it has only 1 button. My wife by accident deactivated the alarm by switching the motor on while the alarm was active. I need to reprogram the current remote.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
1. Enter 5-digit permanent entry code into the keyless entry keypad. 2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then unlock confirming you are in programming mode. 3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will cycle to indicate succesful programming. 4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again to indicate succesfull programming. (If the keypad light goes out before all remotes are programmed the entire process must be repeated). 5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.
You did it like this ?
Programming -Keyless Entry Remote Transmitter
NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time. NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered. NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.
Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met. Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.
Here are the instructions from the factory service manual: 1. Enter 5-digit permanent entry code into the keyless entry keypad. 2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then unlock confirming you are in programming mode. 3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will cycle to indicate succesful programming. 4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again to indicate succesfull programming. (If the keypad light goes out before all remotes are programmed the entire process must be repeated). 5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.
Note: Entering the programming mode cancels all learned keyless remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the system from exiting the programming mode. 1. Turn ignition switch to ON (II) 2. Press the LOCK or UNOCK button on one of the remotes. (An unprogrammed remote can be used for this step.) 3. Turn ignition switch to LOCK (0) 4. Repeat steps 1, 2 and 3 two more times using the same keyless remote used in step 2 5. Turn the ignition switch to ON (II) 6. Press the LOCK or UNLOCK button the same remote. Make sure the power door locks cycle to confirm you are in programming mode. 7. Press the LOCK or UNLOCK button on each remote you want to program. Make sure door locks cycle after you push each remote button to confirm system has accepted the remote. 8. Turn the igniton switch to LOCK (0) to exit programming mode. 9. Test remote(s)
. Enter 5-digit permanent entry code into the keyless entry driver door keypad.
2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then unlock confirming you are in programming mode. 3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will cycle to indicate succesful programming. 4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again to indicate succesfull programming. (If the keypad light goes out before all remotes are programmed the entire process must be repeated). 5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.
If u have the system here is how you program it this is from the owners guide.
1.. Turn ignition to RUN or ACC. 2. Momentarily jump pins in programming connector located in LR quarter panel area (Connector will not be plugged into anything, it will have two pins inside it, if you have to unlug it you have the WRONG one. Not all vehicles are set up from factory for keyless remotes) All doors will lock then unlock to confirm programming mode. 3. Press any button on first keyless remote. Door locks will cycle to confirm programming. 4. If programming a second keyless remote, press any button on second keyless remote. Door locks will cycle to confirm programming. 5. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode
SECTION 501-14B: Keyless Entry/Computer Operated Locks
1999 Town Car Workshop Manual
GENERAL PROCEDURES
Programming —Keyless Entry Keypad Code
Enter the permanent factory keyless entry keypad code.
Press the 1/2 button within five seconds to activate the programming mode. Holding the 1/2 button for more than two seconds will erase all stored customer codes. The existing codes do not need to be erased to program new codes.
Enter the new five-digit keyless entry keypad code.
To associate the new code with personality positions 1, 2 or 3, press the 1/2 button within 5 seconds of entering the 5th digit of the new code for position 1 or 3/4 button for position 2 or 5/6 for position 3. The door locks will lock and unlock confirming the new code is programmed.
If another code is to be programmed, begin entering the code within 5 seconds of the last button pressed.
After all new keyless entry codes are programmed:
Press keyless entry keypad buttons 7/8 and 9/0 at the same time to exit the program mode.
Wait for 5 seconds; the driver door module (DDM) will exit the program mode automatically.
Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming program mode has been entered.
NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased. Press any button on the transmitter to be programmed.
If additional keyless entry remote transmitters are to be programmed, repeat step 2 within 7.5 seconds.
To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------
Programming —Remote Memory Activation
NOTE: This procedure must be completed within 5 seconds.
Press the SET button on the driver door panel.
Press any button on the keyless entry remote transmitter to be associated with a memory setting.
Press the 1 or 2 memory button on the driver door panel.
-------------------------------------------------------------
Programming —Autolock and Horn Chirp
NOTE: This procedure must be completed within 30 seconds. Turn the ignition switch to RUN.
Press the UNLOCK button three times.
Turn the ignition switch to OFF.
Press the UNLOCK button three times.
Turn the ignition switch to RUN. The doors will lock and unlock to confirm entry into program mode.
Press the UNLOCK button once to toggle the Autolock feature on or off, or twice to toggle the Horn Chirp function on or off. The horn will chirp to confirm toggling of the Autolock feature.
Exit program mode by turning the ignition to OFF, START, or wait 7.5 seconds.
here's the instructions for a 97 TL - I hope they're the same.
Note: Entering the programming mode cancels all learned keyless remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode. You must complete each step within 4 seconds of the previous step to keep the system from exiting the programming mode. You must program remotes within 10 seconds of each other 1. Turn ignition switch to ON (II) 2. Within 4 seconds press the LOCK or UNOCK button on one of the remotes. (An unprogrammed remote can be used for this step.) 3. Within 4 seconds turn ignition switch to LOCK (0) position 4. Within 4 seconds turn the ignition switch to ON (II) 5. Repeat steps 2, 3 and 4 two more times using the same keyless remote used in step 2 6. Within 4 seconds press the LOCK or UNLOCK button on the same remote. Make sure the power door locks cycle to confirm you are in programming mode. 7. Within 10 seconds press the LOCK or UNLOCK button on same remote. 8. Within 10 seconds press the LOCK or UNLOCK button on all other remotes you want to program. Make sure door locks cycle after you push each remote button to confirm system has accepted the remote. 9. Turn the igniton switch to LOCK (0) to exit programming mode. 10. Test remote(s)
Note: Entering the programming mode cancels all learned keyless remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode.
You must complete each step within 4 seconds of the previous step to keep the system from exiting the programming mode. You must program remotes within 10 seconds of each other 1. Turn ignition switch to ON (II) 2. Within 4 seconds press the LOCK or UNOCK button on one of the remotes. (An unprogrammed remote can be used for this step.) 3. Within 4 seconds turn ignition switch to LOCK (0) position 4. Within 4 seconds turn the ignition switch to ON (II) 5. Repeat steps 2, 3 and 4 two more times using the same keyless remote used in step 2 6. Within 4 seconds press the LOCK or UNLOCK button on the same remote. Make sure the power door locks cycle to confirm you are in programming mode. 7. Within 10 seconds press the LOCK or UNLOCK button on same remote.
8. Within 10 seconds press the LOCK or UNLOCK button on all other remotes you want to program. Make sure door locks cycle after you push each remote button to confirm system has accepted the remote. 9. Turn the igniton switch to LOCK (0) to exit programming mode. 10. Test remote(s)
Hi Darryl Jaftha
Please verify make and model and year again.
×