Question about 2013 Dodge Avenger

1 Answer

Where is camshaft position sensor located? - 2013 Dodge Avenger

Posted by Alex on

Ad

1 Answer

Mik Dee

Mik Dee

  • Level 1:

    An expert who has achieved level 1.
    New Friend:

    An expert that has 1 follower.
    Corporal:

    An expert that has over 10 points.
    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 18 Answers
Ad

5 Related Answers

AzVip

  • 114 Answers

SOURCE: Camshaft sensor location

The cam sensor on the 4.7 is located toward the forward edge of the right cylinder head (passenger side). This has a 3 wire connector, tan/with yellow tracer is sensor signal, black / light blue tracer wire is sensor ground and the orange is the 5V supply.

Posted on Mar 22, 2009

Ad
Molson02536

Harvey N Tawatao

  • 3854 Answers

SOURCE: need help finding camshaft position sensor

2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.
Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
 - Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
 - Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
 - Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
 The camshaft position sensor is mounted in the front of the head.
Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
 Without pulling on the connector, pull the sensor out of the chain case cover.
Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
 - Attach electrical connector to sensor.
Good luck and hope this helps






Posted on May 03, 2009

Jonah Oneal

  • 14092 Answers

SOURCE: where is the camshaft position sensor located on a

the camshaft sensor is mounted on the camshaft housing located on the end of the cylinder head.

Posted on Jul 09, 2009

techbuster

INDIRA KUMAR

  • 5081 Answers

SOURCE: P0340 Camshaft Position Sensor. How do I fix it?

http://www.youtube.com/watch?v=ve1XW5Ul8Os
please go the above link and you have a video procedure for how to change the sensor.
just do it and you are done to drive your car away.

Posted on Aug 09, 2009

Anonymous

  • 236 Answers

SOURCE: 2001 dodge ram 1500 5.9 camshaft position sensor

CAMSHAFT POSITION SENSOR 2001 Dodge Truck RAM 1500 1/2 ton 2WD 5.9L SFI 8cyl The Camshaft Position Sensor is located: Under hood, center, upper engine area, rear of intake manifold, mounted in distributor

If this is helpful.Please leave ositive Feedback. Thanks, SnugglePants

Posted on Oct 21, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Saturn Outlook Cam Position Sensor Location 3.6 engine
(1) Camshaft Position (CMP) Actuator Solenoid - Intake Bank 1
(2) Camshaft Position (CMP) Sensor - Intake Bank 1
(3) Camshaft Position (CMP) Sensor - Intake Bank 2
(4) Camshaft Position (CMP) Actuator Solenoid - Intake Bank 2
(5) Camshaft Position (CMP) Actuator Solenoid - Exhaust Bank 2
(6) Camshaft Position (CMP) Sensor - Exhaust Bank 2
(7) Generator
(8) A/C Compressor Clutch
(9) Camshaft Position (CMP) Actuator Solenoid - Exhaust Bank 1
(10) Camshaft Position (CMP) Sensor - Exhaust Bank 1

Mar 22, 2018 | Saturn Cars & Trucks

1 Answer

Where is the camshaft position sensor located on a 2005 cadillac deville base model?
LOCATION
The camshaft position sensor is located on the rear cylinder bank in front of the exhaust camshaft. The camshaft position sensor extends into the rear cylinder head and is sealed with an O-ring.


26349435-oucqd2i3pucu3s1utbyq1gmo-1-0.gif

Nov 10, 2016 | 2005 Cadillac Deville

1 Answer

Locate camshaft sensor 2008 3.6l malibu
Which one ?
Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake

Sep 02, 2016 | 2008 Chevrolet Malibu

1 Answer

Where is the camshaft position sensor located in my 2010 Honda accord LX 2.4 4 cyl
see the diagram and videos I found for you. The fir5st one gives a brief overview and removal instructions




2007 Honda Civic Camshaft Crankshaft Position Sensors Location 2010 honda accord camshaft position sensor Google Search Repair Guides Electronic Engine Controls Camshaft Position Sensor AutoZone...



26179497-ovcnn2xiniiieohoqxqovc5y-1-0.gif

Apr 29, 2016 | Honda Cars & Trucks

1 Answer

Where is the camshaft position sensor located in a
The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The camshaft position sensor is either located near the top of the engine, passenger-s side, or on the right side of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the camshaft pulley.
This sensor is located at the front of the engine near the camshaft gear this is what I got 6 different locations manual covers 99-05

Oct 10, 2014 | Cars & Trucks

2 Answers

Where is 2003 ford focus camshafts position sensor
Camshaft Position Sensor
The camshaft position (CMP) sensor detects the position of the camshaft. The CMP sensor identifies when piston No. 1 is on its compression stroke. A signal is then sent to the powertrain control module (PCM) and used for synchronizing the firing of sequential fuel injectors. The Coil On Plug (COP) Ignition applications also use the CMP signal to select the proper ignition coil to fire. The input circuit to the PCM is referred to as the CMP input or circuit.
There are two types of CMP sensors: the three pin connector Hall-effect type sensor (Figure 25) and the two pin connector variable reluctance sensor

a452a319-2d08-4e59-9885-fe43b5fc7f61.gif

and next the location of 2003 ford focus camshafts position sensor
96d62950-03fc-4668-b3ad-dfa939f76b14.gif

Sep 13, 2014 | 2003 Ford Focus

1 Answer

Camshaft position sensor
ON THE 4 CYLINER ENGINE CAMSHAFT SENSOR LOCATED AT THE LEFT DRIVERS SIDE OF THE TIMING COVER. THE V - 6 ENGINES CAMSHAFT POSITION SENSOR LOCATED AT THE FRONT OF ENGINE BLOCK BELOW THE POWER STEERING PUMP.

Aug 28, 2012 | 2000 Oldsmobile Bravada

2 Answers

Need help finding camshaft position sensor
2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.
Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
 - Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
 - Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
 - Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
 The camshaft position sensor is mounted in the front of the head.
Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
 Without pulling on the connector, pull the sensor out of the chain case cover.
Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
 - Attach electrical connector to sensor.
Good luck and hope this helps





May 02, 2009 | Dodge Stratus Cars & Trucks

1 Answer

1993 ford taurus, replaced all starting and charging componets still no spark to plugs. Checked all fuses and all fusible links. Replaced key switch, ignition switch,neutral safty...
The camshaft position sensor sends a signal to the PCM, powertrain control module. The PCM then determines spark plug firing. Could be the camshaft position sensor.

1996 is all I have
Camshaft Position (CMP) Sensor 3.0L (2V) Engine
The camshaft position sensor (CMP sensor) (12126):
  • is a single Hall-effect magnetic switch activated by a single vane which is driven by the camshaft (6250).
  • provides camshaft position information which is used by the ignition coil (12029) and the powertrain control module (PCM) (12A650) for fuel synchronization.
3.0L (4V) Engine
The camshaft position sensor (CMP sensor) (6B288) is:
  • a variable reluctance sensor.
  • triggered by the high-point mark on the LH exhaust camshaft sprocket (6256).
-----------------
3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder block.
Installation
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 75 degrees counterclockwise from the rear face of the cylinder block. This step will locate camshaft position sensor electrical connector in the pre-removal position.
  1. Roatate Syncro Positioning Tool T95T-12200-A clockwise slightly. This will engage oil pump intermediate shaft. Push downward while adjusting Syncro Positioning Tool T95T-12200-A until the Syncro Gear engages the camshaft gear.
  1. When synchronizer flange is fully seated against block, the installation tool should be facing counterclockwise of engine centerline approximately 33 to 45 degrees.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (13-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.
824fa44.gif
Item Part Number Description 1 T95T-12200-A Syncro Positioning Tool 2 — Water Outlet (Part of Intake Assy) 3 9424 Intake Manifold 4 N602704-S Screw and Washer 5 12126 Camshaft Position Sensor 6 12A362 Synchronizer Assembly 7 12270 Hold-Down Clamp A — Tighten to 1.5-4 Nm (13-35 Lb-In) B — Tighten to 19-30 Nm (14-22 Lb-Ft)

Apr 04, 2009 | 1993 Ford Taurus

1 Answer

1997 mercury sable camshaft sensor replacement
do you have 3.L 2v or 4 valve?

3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder blocks (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (12270) (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder blocks.
Installation
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be used to position the synchronizer assembly prior to installation of the camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs. Locate camshaft position sensor electrical connector in the pre-removal position.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (14-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.

Feb 22, 2009 | 1997 Mercury Sable

Not finding what you are looking for?

View Most Popular

2013 Avenger

  • Cars & Trucks

Related Question

2007 Saturn Outlook Cam Position Sensor Location 3.6 engine

  • Saturn Cars & Trucks

Open Questions:

0 Answers

2013 2.4l coil on plug. It has a misfire no 1 swapped coils and it follows, bought a new coil and the same thing misfire PO301 and it still follows the coil.

Dec 08, 2019 | 2013 Dodge Avenger

0 Answers

how do I remove tcs109 shift seloniod 2013 dodge avenger

May 14, 2018 | 2013 Dodge Avenger

0 Answers

2013 dodge avenger tcs109 removal

May 14, 2018 | 2013 Dodge Avenger

0 Answers

2013 dodge avenger dies when driving

Jan 30, 2017 | 2013 Dodge Avenger

See all 2013 Dodge Avenger Questions

Related Topics

2013 Dodge Avenger Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

2011 Dodge Avenger

2008 Dodge Avenger

2008 Dodge Avenger

2008 Dodge Avenger

2009 Dodge Avenger

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...