How do I replace a rear motor mount on 1997 Chrysler Cirrus?

Here you are - power rack & pinion.

Except 2.2L and 1993-96 3.1L Engines
See Figure 1

1. Raise the intermediate shaft seal and remove intermediate shaft-to-stub shaft pinch bolt.
2. Remove the air cleaner and disconnect the pressure hoses from the steering gear.
3. Raise and support the vehicle on jackstands, then remove both front wheel and tire assemblies.
4. Remove the cotter pins and nuts from both tie rod ends. Using tool J-6627 or BT-7101, press the tie rod ends from the steering knuckle.
5. If equipped with an Air Management pipe, remove the bracket bolt from the crossmember.
6. Remove the 2 rear cradle mounting bolts and lower the rear of the cradle about 4-5 in. (102-127mm).

WARNING
If the rear of the cradle is lowered too far, the engine components nearest the cowl may be damaged.

1. If equipped, remove the rack and pinion heat shield.

Fig. Fig. 1: Power rack and pinion assembly

1. Remove the rack and pinion mounting bolts, then the gear assembly through the left wheel opening.

To install:

1. Install the gear assembly through the left wheel opening and install the mounting bolts.
2. Install the heat shield.
3. Raise the rear of the cradle and install the mounting bolts.
4. Install the bracket bolt to the crossmember under the air management pipe.
5. Install the tie rod ends to the steering knuckles, install the retaining nuts and insert new cotter pins.
6. Install the front wheels and lower the vehicle.
7. Install the high pressure hoses to the steering gear and install the air cleaner.
8. Install the intermediate shaft seal and the intermediate shaft-to-stub shaft pinch bolt.

2.2L Engine

1. Disconnect the negative battery cable.
2. Install an engine support fixture J-28467-A, or the equivalent.
3. Raise and safely support the vehicle.
4. Remove the tire and wheel assembly.
5. Remove the intermediate shaft lower pinch bolt.
6. Disconnect the intermediate shaft from stub shaft.

CAUTION
Failure to disconnect the intermediate shaft from the rack and pinion stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage can cause loss of steering control which could result in personal injury.

1. Remove the exhaust pipe hanger bracket near rear of frame including the brake line retainer and rubber exhaust pipe hangers.
2. Remove the engine and transaxle mount nuts at the subframe.
3. Support the rear of the subframe with jack stands.
4. Remove the rear subframe bolts and discard.
5. Lower the subframe for access to rack and pinion.

Do not lower the rear of the cradle too far, as damage to engine components nearest the cowl may result.

1. Remove the cotter pins and castle nuts from the outer tie rod ends and separate the tie rod ends from the steering knuckles using a suitable puller.
2. Disconnect the power steering lines from the steering gear.
3. Remove the rack and pinion mounting bolts and nuts.
4. Remove the rack and pinion through left wheel opening.

To Install:

1. Install the rack and pinion through left wheel opening.
2. Install the rack and pinion mounting bolts and nuts and tighten to 66 ft. lbs. (90 Nm).
3. Connect the power steering lines to the rack using new O-rings and tighten the fittings to 13 ft. lbs. (17 Nm) on the return line and 21 ft. lbs. (28 Nm) on the pressure line.
4. Install the power steering line clip to steering gear.
5. Connect the tie rod ends to the steering knuckles. Tighten the castle nuts to 31 ft. lbs. (42 Nm). Install new cotter pins.
6. Raise the subframe into position and install new frame mounting bolts. Tighten the bolts to 103 ft. lbs. (140 Nm).
7. Remove the jack.
8. Install the engine mount and transaxle mount nuts and tighten to 39 ft. lbs. (53 Nm).
9. Install the exhaust pipe hanger bracket near the rear of frame including brake line retainer and rubber exhaust pipe hanger.
10. Connect the intermediate shaft to the stub shaft and tighten the pinch bolt to 29 ft. lbs. (40 Nm).
11. Install the tire and wheel assembly.
12. Lower the vehicle.
13. Remove the support fixture.
14. Connect the negative battery cable.
15. Refill the power steering reservoir and bleed the system.
16. Check the front end alignment and adjust as necessary.

3.1L Engine (VIN M)

1. Disconnect the negative battery cable.
2. Remove engine torque strut from engine.
3. Install an engine support fixture J-28467-A, or the equivalent.
4. Raise and safely support the vehicle.
5. Remove the tire and wheel assembly.
6. Remove the cotter pins and castle nuts from the outer tie rod ends and separate the tie rod ends from the steering knuckles using a suitable puller.
7. Remove the center engine and rear transaxle mounts from the frame.
8. Remove the intermediate shaft lower pinch bolt.
9. Disconnect the intermediate shaft from stub shaft.

CAUTION
Failure to disconnect the intermediate shaft from the rack and pinion stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage can cause loss of steering control which could result in personal injury.

1. Remove the brace bolts and brace, including brake line brace.
2. Support the rear of the subframe with jack stands.
3. Remove the rear subframe bolts and discard.
4. Lower the subframe for access to rack and pinion.
5. Remove the steering gear heat shield.
6. Remove the clip holding lines at rack assembly.
7. Disconnect the power steering lines and O-rings.
8. Remove the rack and pinion mounting bolts and nuts.
9. Remove the rack and pinion unit through the left wheel well.

To Install:

1. Install the rack and pinion through left wheel opening.
2. Install the rack and pinion mounting bolts and nuts and tighten the mounting bolts to 66 ft. lbs. (90 Nm).
3. Connect the power steering lines to the rack using new O-rings and tighten the fittings to 13 ft. lbs. (17 Nm) on the return line and 21 ft. lbs. (28 Nm). on the pressure line.
4. Install the power steering line clip to steering gear.
5. Install the steering gear heat shield.
6. Raise the subframe into position and install new frame mounting bolts. Tighten the bolts to 103 ft. lbs. (140 Nm).
7. Remove the jack.
8. Install the engine mount and transaxle mount nuts and tighten to 39 ft. lbs. (53 Nm).
9. Install the brace and bolts including brake line brace.
10. Connect the intermediate shaft to the stub shaft and tighten the pinch bolt to 29 ft. lbs. (40 Nm).
11. Connect the tie rod ends to the steering knuckles. Tighten the castle nuts to 31 ft. lbs. (42 Nm). Install new cotter pins.
12. Install the tire and wheel assembly.
13. Lower the vehicle.
14. Remove the support fixture.
15. Connect the negative battery cable.
16. Refill the power steering reservoir and bleed the system.
17. Check the front end alignment and adjust as necessary.

You aren't saying what engine is in it, or whether it is manual or power steering. Here is the R/R procedure for power steering rack for all engine sizes.

Except 2.2L and 1993-96 3.1L Engines
See Figure 1

1. Raise the intermediate shaft seal and remove intermediate shaft-to-stub shaft pinch bolt.
2. Remove the air cleaner and disconnect the pressure hoses from the steering gear.
3. Raise and support the vehicle on jackstands, then remove both front wheel and tire assemblies.
4. Remove the cotter pins and nuts from both tie rod ends. Using tool J-6627 or BT-7101, press the tie rod ends from the steering knuckle.
5. If equipped with an Air Management pipe, remove the bracket bolt from the crossmember.
6. Remove the 2 rear cradle mounting bolts and lower the rear of the cradle about 4-5 in. (102-127mm).

WARNING
If the rear of the cradle is lowered too far, the engine components nearest the cowl may be damaged.

1. If equipped, remove the rack and pinion heat shield.

Fig. Fig. 1: Power rack and pinion assembly

1. Remove the rack and pinion mounting bolts, then the gear assembly through the left wheel opening.

To install:

1. Install the gear assembly through the left wheel opening and install the mounting bolts.
2. Install the heat shield.
3. Raise the rear of the cradle and install the mounting bolts.
4. Install the bracket bolt to the crossmember under the air management pipe.
5. Install the tie rod ends to the steering knuckles, install the retaining nuts and insert new cotter pins.
6. Install the front wheels and lower the vehicle.
7. Install the high pressure hoses to the steering gear and install the air cleaner.
8. Install the intermediate shaft seal and the intermediate shaft-to-stub shaft pinch bolt.

2.2L Engine

1. Disconnect the negative battery cable.
2. Install an engine support fixture J-28467-A, or the equivalent.
3. Raise and safely support the vehicle.
4. Remove the tire and wheel assembly.
5. Remove the intermediate shaft lower pinch bolt.
6. Disconnect the intermediate shaft from stub shaft.

CAUTION
Failure to disconnect the intermediate shaft from the rack and pinion stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage can cause loss of steering control which could result in personal injury.

1. Remove the exhaust pipe hanger bracket near rear of frame including the brake line retainer and rubber exhaust pipe hangers.
2. Remove the engine and transaxle mount nuts at the subframe.
3. Support the rear of the subframe with jack stands.
4. Remove the rear subframe bolts and discard.
5. Lower the subframe for access to rack and pinion.

Do not lower the rear of the cradle too far, as damage to engine components nearest the cowl may result.

1. Remove the cotter pins and castle nuts from the outer tie rod ends and separate the tie rod ends from the steering knuckles using a suitable puller.
2. Disconnect the power steering lines from the steering gear.
3. Remove the rack and pinion mounting bolts and nuts.
4. Remove the rack and pinion through left wheel opening.

To Install:

1. Install the rack and pinion through left wheel opening.
2. Install the rack and pinion mounting bolts and nuts and tighten to 66 ft. lbs. (90 Nm).
3. Connect the power steering lines to the rack using new O-rings and tighten the fittings to 13 ft. lbs. (17 Nm) on the return line and 21 ft. lbs. (28 Nm) on the pressure line.
4. Install the power steering line clip to steering gear.
5. Connect the tie rod ends to the steering knuckles. Tighten the castle nuts to 31 ft. lbs. (42 Nm). Install new cotter pins.
6. Raise the subframe into position and install new frame mounting bolts. Tighten the bolts to 103 ft. lbs. (140 Nm).
7. Remove the jack.
8. Install the engine mount and transaxle mount nuts and tighten to 39 ft. lbs. (53 Nm).
9. Install the exhaust pipe hanger bracket near the rear of frame including brake line retainer and rubber exhaust pipe hanger.
10. Connect the intermediate shaft to the stub shaft and tighten the pinch bolt to 29 ft. lbs. (40 Nm).
11. Install the tire and wheel assembly.
12. Lower the vehicle.
13. Remove the support fixture.
14. Connect the negative battery cable.
15. Refill the power steering reservoir and bleed the system.
16. Check the front end alignment and adjust as necessary.

3.1L Engine (VIN M)

1. Disconnect the negative battery cable.
2. Remove engine torque strut from engine.
3. Install an engine support fixture J-28467-A, or the equivalent.
4. Raise and safely support the vehicle.
5. Remove the tire and wheel assembly.
6. Remove the cotter pins and castle nuts from the outer tie rod ends and separate the tie rod ends from the steering knuckles using a suitable puller.
7. Remove the center engine and rear transaxle mounts from the frame.
8. Remove the intermediate shaft lower pinch bolt.
9. Disconnect the intermediate shaft from stub shaft.

CAUTION
Failure to disconnect the intermediate shaft from the rack and pinion stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage can cause loss of steering control which could result in personal injury.

1. Remove the brace bolts and brace, including brake line brace.
2. Support the rear of the subframe with jack stands.
3. Remove the rear subframe bolts and discard.
4. Lower the subframe for access to rack and pinion.
5. Remove the steering gear heat shield.
6. Remove the clip holding lines at rack assembly.
7. Disconnect the power steering lines and O-rings.
8. Remove the rack and pinion mounting bolts and nuts.
9. Remove the rack and pinion unit through the left wheel well.

To Install:

1. Install the rack and pinion through left wheel opening.
2. Install the rack and pinion mounting bolts and nuts and tighten the mounting bolts to 66 ft. lbs. (90 Nm).
3. Connect the power steering lines to the rack using new O-rings and tighten the fittings to 13 ft. lbs. (17 Nm) on the return line and 21 ft. lbs. (28 Nm). on the pressure line.
4. Install the power steering line clip to steering gear.
5. Install the steering gear heat shield.
6. Raise the subframe into position and install new frame mounting bolts. Tighten the bolts to 103 ft. lbs. (140 Nm).
7. Remove the jack.
8. Install the engine mount and transaxle mount nuts and tighten to 39 ft. lbs. (53 Nm).
9. Install the brace and bolts including brake line brace.
10. Connect the intermediate shaft to the stub shaft and tighten the pinch bolt to 29 ft. lbs. (40 Nm).
11. Connect the tie rod ends to the steering knuckles. Tighten the castle nuts to 31 ft. lbs. (42 Nm). Install new cotter pins.
12. Install the tire and wheel assembly.
13. Lower the vehicle.
14. Remove the support fixture.
15. Connect the negative battery cable.
16. Refill the power steering reservoir and bleed the system.
17. Check the front end alignment and adjust as necessary.

Idler arm? I believe you should have rack and pinion.

There are few help links showing exact accurate procedure to replace Rack and Pinion. Click the link below and follow the procedure:-----
Pinion Seal Replace on Dodge Dakota? http://howtobyme.blogspot.in/2012/04/pinion-seal-replace-on-dodge-dakota.html

-----------

How to Replace a Rear Pinion Seal.
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-pinion-seal.html
------------

How to replace Power steering rack and pinion gear on Chevy Silverado 2500 HD? http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-rack-and.html

----------
How to replace Power Rack and Pinion Steering Gear on Acura Car Models? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-rack-and-pinion.html

-----------
How to replace power rack and pinion steering gear on Toyota cruiser? http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-power-rack-and-pinion.html

----------

How to replace Power Rack and Pinion Steering Gear on Acura Car Models? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-rack-and-pinion.html


------------
Front Drive Pinion Seal Removal on Ford Explorer? http://repairhelpcenter.blogspot.in/2012/03/front-drive-pinion-seal-removal-on-ford.html

-------------
How to Replace Driveshaft, Pinion Flange & Seal?

http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-driveshaft-pinion-flange.html

------------

How to Replace Power Rack & Pinion Steering Gear On 2007 Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html


----------
How to Remove Power Rack & Pinion Steering Gear on Ford Windstar? http://repairhelpcenter.blogspot.in/2012/03/how-to-remove-power-rack-pinion.html

-----------

Power Rack & Pinion Steering Gear replacing details for Buick Park Avenue and Pontiac Bonneville

http://repairhelpcenter.blogspot.in/2012/03/power-rack-pinion-steering-gear.html

-------------

How to Replace Power Rack & Pinion Steering Gear on Mercedes Benz Truck? http://howtobyme.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html


---------
How to replace Power Rack & Pinion Steering Gear on Toyota 4Runner? http://howtobyme.blogspot.in/2012/03/how-to-replace-power-rack-pinion_27.html

-----------

Power Rack & Pinion Steering Gear Replacing on Toyota Land Cruiser & Sequoia? http://schematicsdiagram.blogspot.in/2012/03/power-rack-pinion-steering-gear.html

----------
Power Rack & Pinion Steering Gear Removal on Toyota RAV4? http://repairhelpcenter.blogspot.in/2012/03/power-rack-pinion-steering-gear-removal.html

----------
How to Replace Power Rack & Pinion Steering Gear on Toyota Sienna? http://technoanswers.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html

------------
These details will help.
Thanks.

Oh yeah, you sure can! We must have a lot of them (use the search feature)! But likely not near all that the chrysler breeze is known for. I recently changed out a rack and pinion unit on a chrysler cirrus (exact same set-up as your breeze) and it was major fun on my driveway for about a week! I have to say though, that the engine and electronic controls on the cirrus has been superb and trouble free the last two years, (unlike other comments or questions I often see), and the car is approaching 220 thousand miles now, it being a '96.

look inside the steering column for a bad wire the switch on the rack if for turing th eac of when tight turning

check the power steering fluid level..

Is it allwheel drive or rear wheel drive ? makes a difference where rack is mounted. If I remember right rear whl drive rack is mounted behind frt tires and awd is in frt of tires.

your vehicle has a transverse mounted engine and most newer vehicls have rack and pinion steering versus a shaft going to a gear box with a drag link and sway bar type steering system. most full size suvs have the gear box set up. some suvs like dodge durango have both a gear box and a rack and pinion. your vehicle has only the rack and pinion

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008948b