I have a Holden cruze cd diesel 2009. The key is stuck in the ignition and the lever won't come out of park. The engine starts ok. What could be the problem

try wiggling the steering wheel and gently turn key at same time to unlock steering lock

Some cars have an interlock between the Shift lever and the ignition key. Make sure you have the shift lever all the way into the Park position.

Hi Chris This sounds like a return to Holden for repair. The chance is the fault is the ignition barrel It may need replacement. I have known in the past where people after stopping the engine and exiting the car grab the steering wheel and put there weight against the locking pin in the ignition barrel via the downward force on the steering wheel this can bend the pin and then its a matter of time before it locks up. The only way to make a correct diagnosis is for someone to to look at your car. I hope this information is of some help Good luck

I have never seen this issue posted. And yes the dealer is right about the body control module.

Is it shifter on the floor ?
Ignition Lock Cylinder Control Actuator
If the vehicle is equipped with a floor mounted console gear shifter, it has a ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator's purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in gear and the vehicle may still be moving. The column ignition lock system consists of a ignition lock cylinder control actuator , and a park position switch that is located in the A/T shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded out to mechanically prevent the ignition key cylinder from being turned to the lock position when vehicle transmission is not in the Park position. If vehicle power is lost, and/or the transmission is not in the Park position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column.

GM had problems with these ! Has a TSB - technical service bulletin !
Automatic Transmission Shift Lock Control Description and Operation
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock solenoid (serviced as the automatic transmission shift lock actuator), as well as the body control module (BCM) and the engine control module (ECM). The shift lock solenoid is located within the floor shift control assembly with vehicles equipped with floor shift.
• The BCM controls the voltage to the shift lock control solenoid through the shift lock control solenoid controlled voltage circuit. The following conditions must be met before the BCM will remove voltage from the shift lock solenoid:
- The ignition is in the ON position.
- The engine control module (ECM) sends an input via GMLAN serial data to the BCM indicating the transmission is in the PARK position.
- The BCM determines the brake pedal is applied according the brake pedal position.
Since the shift lock control solenoid is permanently grounded, the BCM supplies voltage to the automatic transmission shift lock control solenoid, mechanically locking the shift lever in the PARK position as the solenoid energizes. When the brake pedal is applied, the BCM turns the control voltage output of the shift lock control solenoid OFF, de-energizing the shift lock control solenoid. The de-energized solenoid releases the mechanical lock allowing the driver to move the shift lever out of the PARK position. When the transmission is out of the PARK position, the shift lock control solenoid remains de-energized.
During remote start operation, the BCM will energize the shift lock control circuit, locking the shift lever in the PARK position.
Replaced shifter on a cobalt , broken plastic part inside , wouldn't press on micro switch to disengage ! Found replacement shifter at auto slavage yard .$20.00 US

Yes. It can be removed and fixed

The stuck in park is easy disconnect the linkage at the transmission and move the selector red by two notches (by hand) this will place the transmission in neutral if there is resistance chock the wheels release the handbrake and rock the car ( back and forward to take load off the parking parking pawl which is stuck) no electrics is because of the ignition position remove the ignition switch from the column this isolates from the ignition lock and manually move the slide until the engine starts (make sure the hoot & hand brake are applied in case you ******* up the selector job and left it in gear. once the engine starts reconnect the transmission linkage. restart the engine and run the selector through the gears if all is OK.either cut the old ignition lock off the steering column and replace or get a locksmith to remove the key and then re-cut a new key from the spare or from the manufacturers code. all done

Hi I have Holden Cruze 2009 suddenly the car key Connor come out an it was stuck in parking an back light also not working how can I fix the problem

manual lever position switch is bad or out of adjustment