Question about 2011 Ford F-350 Super Duty

1 Answer

6.7l. How can I replace windshield washer pump?

Posted by Melanie Noel on

Ad

1 Answer

Lawrence Oravetz

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    Superstar:

    An expert that got 20 achievements.
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 10,548 Answers

The pump is on the bottom of the washer fluid container. Take out the bottle and remove the pump.

Posted on Mar 11, 2016

  • Melanie Noel Mar 12, 2016

    Anybody have a diagram?

  • Lawrence Oravetz Mar 12, 2016

    You will have to purchase a manual from an auto parts store.

×

Ad

5 Related Answers

emissionwiz

Marvin

  • 85239 Answers

SOURCE: IM TRYING TO FIND THE

the fuse panel is under the plastic panel on the left of the steering wheel, the cruise does not have a deicated fuse, it is controlled by the powertrain control module, if the truck runs the cruise has power, the most common cause of the cruise being inop is he rotating contact under the steering wheel, it is called the clock-spring contact

Posted on Dec 15, 2008

Ad

Anonymous

  • 2317 Answers

SOURCE: my windshield washer is not spraying water, and

I believe it's powered by the windsheild wipers. I would check to see if the washer pump is getting power when operating the switch, if so, the pump itself maybe bad.

Posted on May 03, 2010

Anonymous

  • 85 Answers

SOURCE: 2006 f 350 super duty 6.0 diesel wont start let

high pressure oil curcut often d rings in heads high pressure oil should be 19 - 20 percent duty cycle

Posted on Jul 19, 2010

Anonymous

  • 1 Answer

SOURCE: 1997 ford f super duty windshield wipers are not

Try Looking for the Fuze or Fuze link! Could be wiper Arm itself, under grill's!

Posted on Nov 10, 2010

Donald4x4er

  • 1 Answer

SOURCE: how to replace a transmission temperature sensor

Trans temp sensor

Posted on Jul 20, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How hard is it to re place the windshield washer tank on a 99 Olds mobile silouhett

Oldsmobile Silhouette Windshield Washer Reservoir ' Used ...

www.partshotlines.com > All Makes > Oldsmobile > Silhouette
Find a quality Oldsmobile Silhouette Windshield Washer Reservoir and other used Mini Van parts ... For example: If you're looking for a Hood Latch, ... This part is also known as Oldsmobile Silhouette Wdsh Washer Reserv; ... 1999 MONTANA

How To Install Replace Windshield Washer Pump Many GM ...

? 2:34
https://www.youtube.com/watch?v=jCqbhK_-hjY
Jun 7, 2010 - Uploaded by 1A Auto Parts
How To Install Replace Windshield Washer Pump Many GM Vehicles ... can u tell Me were the Fuse located ...

Oct 29, 2015 | Cars & Trucks

1 Answer

Where is the windshield wiper pump located on dodge caravan 2005
The washer pump is located in the bottom of the washer fluid tank

May 24, 2015 | 2005 Dodge Caravan

1 Answer

Where is the fuse for the water pump for the window washer
A washer pump in a car's windshield wiping system moves washer fluid from a reservoir through hoses. The motorized pump pressurizes the fluid to allow it to be squirted from the hoses through nozzles onto the front and/or rear windshield of a car. The washer fluid helps windshield wipers get rid of rain, dirt, or other objects that can interfere with a driver's visibility. If your washer fluid is not being sent out when activated, the solution could simply be filling the washer system's reservoir with more fluid or cleaning the nozzles and hoses. In more severe cases, the washer pump may need to be replaced. Here are steps to troubleshoot a windshield-washer pump.

Try this link in case you are stuck:

How to Troubleshoot Windshield Washer Pump

Here is another YT video for a similar purpose:

Windshield Washer Pump and System Diagnosis

Apr 13, 2015 | 2001 Ford Explorer Sport Trac

1 Answer

How do you replace the windshield washer pump on 2008 ford focus, wipers work but no spray comes out
The hose could be clogged ! Do you know where you add the washer fluid ? Somewhere on the bottom of that plastic bottle is the washer pump .
Removal and Installation
> WARNING: Windshield washer solution contains methanol, which is poisonous. Observe all cautions and warnings indicated on label of washer solution container. Failure to follow these instructions may result in personal injury.
> CAUTION: When replacing the windshield washer pump be careful not to damage the rubber grommet.
> CAUTION: Do not operate the windshield washer pump before filling the reservoir. Failure to do so could result in premature pump failure.
  1. NOTE: When installing the reservoir, the filler neck must be lubricated using a water-based lubricant.
    Remove the bolt and the windshield washer reservoir filler neck.
  1. Remove the RH fender splash shield. For additional information, refer to Section 501-02 .
  1. Remove the foam filler and remove the retainer.
  1. Remove the 2 screws and the accessory drive splash shield.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the nut, 2 bolts and position the A/C accumulator aside.
    • To install, tighten to 9 Nm (80 lb-in).
  1. Unclip the A/C lines from the inner fender well.
  1. Drill out the rivet and remove the bracket.
  1. Remove the 2 bolts, slide the windshield washer reservoir assembly forward to release it, and position the washer reservoir aside.
    • Install the upper bolt followed by the lower bolt, and tighten to 5 Nm (44 lb-in).
  1. Disconnect the windshield washer tube assembly from the pump and release the windshield washer tube assembly from the washer reservoir.
  1. Disconnect the electrical connector from the windshield washer pump.
  1. Release the wiring harness from the reservoir, and remove the washer reservoir.
  1. To install, reverse the removal procedure.

Apr 07, 2015 | Ford Cars & Trucks

1 Answer

How to replace the windshield washer pump
pump is in washer resevoir. disconnect electrical plug and hoses then pull pump out.

May 10, 2010 | 1999 Chevrolet Lumina

1 Answer

Windshield washer not working
If you hear the pump running when you try to use the washer pull off the lines on the pump and make sure they're clear. If the lines are clear you need to replace the nozzles. If you don't hear the pump running at all, replace your windshield washer pump.

Dec 30, 2009 | 2001 Mitsubishi Montero

1 Answer

Mercury villager 1994 washer pump not working
the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal
  1. Disconnect the battery ground cable (14301).
  2. Raise and support the vehicle.
  3. Remove the RH wheel (1007).
  4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
  5. Remove the windshield washer reservoir top bolt.

  6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
  7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
  8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
  9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
  10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.

    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.

  11. Loosen the two windshield washer reservoir side bolts.
  12. Remove the windshield washer reservoir by sliding it out of the side slots.
  13. Remove the windshield washer pump.

    Installation
To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

Sep 09, 2009 | 1994 Mercury Villager

2 Answers

Windshield washer pump quit working. wipers work ok thou. I can't find an exact replacement.
you can buy a in line pump most anywhere and it just goes in the washer fluid line and the wires from your old pump will need the ends changed to make it work.they come with good instruction.

Aug 29, 2009 | 2002 Hyundai Accent

2 Answers

Washer doesn't work and I can't hear the pupmp motor working.
The windshield washer pump is part of the windshield wash reservior.
There is an electrical connector located on the bottom of the reservior.
That is the pump .
If the pump is not in the reservior. I would just trace the washer fluid lines from the sprayer on the vehicle back to the pump. The lines just might lead back to the reservior for the windshield wash solution. Then you will have confirmed the pump is in the reservior.

You may have to get a new reservior. The pump might not be seperate item, I am not 100% sure on that.

I also would double check the fuses and any relays related to the washer pump.

Finally, I would check the washer switch if you replace the pump and still is not working .

Good luck

Mar 31, 2009 | 2002 Chrysler Town & Country

1 Answer

Winshield washer motor does not run
The wiper and washer motors us the same fuse. So if the wipers work, it's not the fuse. The washer motor wiring, the top wire is voltage, bottom wire is ground. As you can see, at the wiper/washer switch, #5 sends voltage for washer motor, you can see the wire colors. If good voltage and ground and no washer action suspect the washer motor. Before replacing anything, make sure the plumbing from washer fluid to windshield is not clogged.
washer 1-pivzycofcmbi0i4mslo0ckpd-1-0.jpg

washer 2-pivzycofcmbi0i4mslo0ckpd-1-2.jpg

May 20, 2017 | 2001 Honda Civic

Not finding what you are looking for?

View Most Popular

2011 F-350 Super Duty

  • Cars & Trucks

Related Question

How hard is it to re place the windshield washer tank on a 99 Olds mobile silouhett

  • Cars & Trucks

Open Questions:

0 Answers

where is the a/c blower motor for a 2011 ford f250?

Jun 19, 2014 | 2011 Ford F-350 Super Duty

0 Answers

how to fix air lock in gas tank of a 2011 f-350

May 15, 2014 | 2011 Ford F-350 Super Duty

0 Answers

How to remove heater fan

Apr 28, 2014 | 2011 Ford F-350 Super Duty

0 Answers

how to replace a blower motor with a/c 2011 ford F-350 super duty

Apr 28, 2014 | 2011 Ford F-350 Super Duty

See all 2011 Ford F-350 Super Duty Questions

Related Topics

2011 Ford F-350 Super Duty Logo

355 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

2 Answers
2001 ford f350 fuse diagram

Ford F-350 Super Duty Cars &...

1 Answer
Resetting oil change light on 2010 F 350

2010 Ford F-350 Super Duty

1 Answer
..torque specs. rod bearings. f-350 2008 diesel 6.4

2008 Ford F-350 Super Duty

1 Answer
My ford 2008 f350 died and wont start it cranks but seems like its not getting fuel

2008 Ford F-350 Super Duty

1 Answer
2008 F-350 6.4 - Where is the fuse box (also

2008 Ford F-350 Super Duty

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...