Why isn't keyless entry working?

According to GM there are 3 components in the RCDLR or RKE remote keyless entry system. My key fobs with new batteries only work standing right next to the car. The range of the key fob dropped at that the same time my TPMS tire pressure monitoring system repair warning came on my dashboard. The problem is that there are 4 different components on the 2015 Malibu. I will provide the GM part numbers for these, if you please tell me where they are and also how to replace them: #13583559 Remote Control Door Lock Receiver #13502554 Antenna #13502551 Ignition Lock Key Transmitter Antenna #13502549 Low Frequency Console Antenna

just reprogram the 98 fobs to the 97 easier instead of ripping out the electrical system can reprogram lock /unlock if have auto start will need dealer to flash the fob
http://freeremoteinstructions.com/ Free Keyless Remote Fob Entry programming instructions procedures for all...

Search Results

2004 Mitsubishi Endeavor Key Fob Remote Programming ...

blog.keylessentryremotefob.com/.../04/2004-mitsubishi-endeavor-key-fo...
Apr 25, 2013 - 2004 Mitsubishi Endeavor Key Fob Remote Programming Instructions ... you might have visit us at Keylessentryremotefob.com You can also ...

Mitsubishi - Free Keyless Remote Fob Entry programming .

How To Replace Mitsubishi Endeavor Key Fob Battery 2004 ...

? 2:04
www.youtube.com/watch?v=yeQRdre7O0Q
Oct 31, 2014 - Uploaded by Keyless Entry Remote Inc
... will show you How To Replace Mitsubishi Endeavor Key Fob Battery 2004 2005 To Order This Remote ...

DLR ONLY Sorry.

does your unlock button work in car? If it does, do you have another keyless entry key fob? If so does it work? If you just replaced the battery you can try removing battery and cleaning contacts within remote. I know some of the nissan altimas had the same issue and the only solution was a new key fob. Good Luck

try this...

1. Make sure vehicle is in Park
2. Press Vehicle Information button (has the icon of a car and an 'i')until 'PRESS *check mark* TO RELEARN REMOTE KEY' displays.
3. Press set/reset button. The message 'REMOTE KEY LEARNING ACTIVE' will display.
4. Press and hold the lock and unlock buttons on the transmitter at the same time for about 15 seconds. A beep will sound indicating that the transmitter is matched.
5. To match additional transmitters at this time, repeat Step 3. Each vehicle can have a maximum of four transmitters matched to it.
6. To exit the program mode, you must cycle the key to LOCK.

If that doesnt work, go to: http://www.bing.com/search?q=how+to+program+a+keyless+entry+fob+for+a+2002+Suzuki+Grand+Vitara&go=&form=QBLH&qs=n&sk=

Here's a link to program your fobs,need to do both at the same time. 2008 Subaru Forester Key Fob Remote Programming Instructions

Do you have a keyless entry FOB. If you do replace the battery then program the system. Unlock the doors turn the ignition key to the "ON" position then press either the lock or unlock button of the FOB turn the ignition key off.Now turn the ignition key on again and press either button on the FOB. Turn the ignition off again. Do this 3 times. This initiates programming for the power door locks. Press the lock button of each remote one at a time to be stored in memory. this must be done within 10 seconds of each remote.
3 remotes max. Turn the ignition off and remove the key to complete programming procedure. then test each remote.

should not be using fob buttons for entry or locking for emergency only .if keyless entry walk up to car with fob do not press any buttons see if door opens then walk away from car with fob about 20m then go back to car without fob and see if door locked if so all working fine .indicators will not flash if the above dont work take back to main dealer for diagnostics keys may need to be reprogrammed

If your keyless entry remote has never worked it either needs to be programmed to the vehicle or it is the incorrect remote part number for they vehicle. First step is to call your local dealership, ask for service, then verify your vehicle came equipped with the keyless entry option and verify the key fob part number. When calling the dealer have your vin# handy, they will need that. Once you have verified your vehicle has keyless entry option and you have the correct keyless entry remote part number then find a locksmith to program the remote to your vehicle. We suggest a locksmith because they are usually more affordable than the dealer and they come to you.

If your keyless entry remote has worked before and it just stopped working, here are a few tips to try to get it working again:

1) Change the battery
Batteries don't last forever, you'll be surprised how often it's just a dead battery! Search our YouTube channel on how to change a key fob battery for your specific year, make, and model!

2) Wipe the board
The board inside your remote can get a lot more filthy than you think! When the board is dirty it can prohibit the contact to the circuit board when you push down on the button. Simply wiping the circuit board off can make your key fob like new again!

3) Get it checked
Go to your local hardware store like AutoZone or Oreilly's. They usually have a RF frequency tester. This little gadget will let you know if your key fob is sending a signal. If it is, you may need to reprogram your key fob to your vehicle

4) The old car battery reset trick
I know this sounds absurd, but it works sometimes and is worth trying. If you exhausted all of the options above, disconnect both terminals on your car battery for 10 minutes. Then reconnect them and try your key fob. This has worked for many people and I have no idea why. If you do, please comment below to explain.

5) New fob!
It might be time for a new key fob! No need to dread over the expensive costs of a new key fob, at Keyless Entry Remote Fob Inc., you can get a refurbished one for a very affordable price! You won't even be able to tell the difference. Just search your vehicle make, model, and year to purchase a key fob or give us a call at 402-671-5100.