Question about 2008 Infiniti FX35

1 Answer

How to fix blinking airbag light

I did already with ignition on and off but after few minutes starts flashing again

Posted by Anonymous on

Ad

1 Answer

mike manning

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Remove positive battery cable from battery an let sit for 30mins then reattach

Posted on Feb 17, 2016

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 cavalier cranks will not start theft light stays on


Is the security light flashing? If so, turn ignition on and wait for 10 minutes and light should stay on solid. Then try and start the car without turning the ignition back off. Then turn off ignition and wait 1 minute. Then turn ignition on and see if security light is flashing. If not try and start your car. If it is flashing, try waiting again with just the ignition on and see if it goes out.

Nov 24, 2012 | Cars & Trucks

1 Answer

Resetting the passlock


1. First, insert the ignition key and turn the ignition switch to the "On" position (Do not start the engine). Leave the switch on for 11 minutes. The security light may flash or be on steady during this 11 minute period. Make sure the light is no longer on or flashing before proceeding to #2 .
2. Turn the ignition switch off for 30 seconds.
3. Turn the ignition switch to the "On" position (as in step #1) for 11 minutes again.
4. Turn the ignition switch off for another 30 seconds.
5. Turn the ignition switch to the "On" position for 11 minutes a third time.
6. Turn the ignition switch off for 30 seconds one final time.
7. Turn the ignition switch to the "On" position one final time and wait 30 seconds.
8. Attempt to start the engine. If the engine starts and runs normally, the relearn is complete. If the engine does not start, Go to this link for info
http://vatspasslockpasskeysecurityhelp.yolasite.com/

Sep 08, 2012 | 2000 GMC Yukon Denali

1 Answer

1992 BUICK LA SABRE, PROBLEM AS FOLLOWS WE HAVE POWER TO THE BOTTOM OF THE STEERING COLUMN FROM IGNITION KEY SWITCH, BUT NO POWER FROM THE SWITCHES AT BOTTOM OF COLUMN TO STARTER SOLENOID, WE'VE TRIED...


it will only run for a few seconds if your key has a transponder that the security system looks for, the security system is tied into the ignition system for starter and ignition.
do you have a security light flashing on dash? if that is the case you have to leave the key in the on position until the light goes off, usually 10 - 15 minutes, once light goes off you should be able to start the engine unless the tumbler is bad, it has the part that reads the transponder in the key.

Oct 01, 2011 | Cars & Trucks

2 Answers

The car fires but stops immediately


I had a problem with a 97 Achieva recently.Someone else replaced the PCM/ignition switch and passlock sensor.I replaced the ICP.Engine would turn over but wouldn't start and the security lamp was dim and flashing and then it would go solid.I tried the wait 10 minutes thing but,the light would never go off! I put the original passlock sensor back onto the lock cylinder. But this is what fixed the problem.I cleaned the contacts on the black wires and green on the ignition switch with tv tuner cleaner! After I cleaned those contacts the security light was flashing brightly.So I turned the key to run and left it there.After a few minutes it stayed on solid.I waited about 10 minutes but the light never went out.So I turned off the switch and then tried starting.It started right up and the security lamp flashed and then went off.Has started every time since.Note:I also scraped the pins that I cleaned with the cleaner with a knife.

Nov 11, 2009 | 1997 Oldsmobile Achieva

1 Answer

D4 light blinks and car wont start


i have a 92' honda accord lx, it has a problem of the D4 light flashing and the car wouldnt start, but i could wait a few minutes and try again and it would start.

Sep 07, 2009 | 1992 Honda Accord

2 Answers

1996 Oldsmobile Achieva: Security light flashes upon startup


Here is what you do, but only when the SECURITY light flashes - if it is always ON or OFF it's no use.
Turn the key in the ignition to ON.
Wait for exactly 10 minutes ( SECURITY light will flash for 10 minutes and then stay on SOLID)
Turn the key to OFF
Wait 5 seconds.
Turn the key in the ignition to ON.
Wait for exactly 10 minutes.
Turn the key to OFF
Wait 5 seconds.
Turn the key in the ignition to ON.
Wait for exactly 10 minutes.
Turn the ignition OFF.

Start the car normally.
It has relearnt the keycode and you're good to go.
NOTICE - it takes 30 minutes to relearn, that's THREE cycles of ON - 10 minutes - OFF.

Good luck.

Jul 11, 2009 | 1996 Oldsmobile Achieva

1 Answer

Car keeps turning off


307 engine? I would try the ignition module.

Mar 27, 2009 | 1983 Oldsmobile Delta 88

2 Answers

Ignition won't turn to drive


if tapping it doesnt work. hit it hard for a few minutes then try to turn it forward and back both then repeat.  I had a tow truck come to tow me and he started banging on mine.  I said i already did that while waiting for you and he said you will see.  he kept doing it and a few minutes later i looked like a ********.  He told me the pins were sticking and a lock smith could take the first 2 pins out for me. 

Mar 20, 2009 | 2003 Chrysler 300M

2 Answers

Mazda 323 2002 Sting Immobilizer


Fcuk I got same problem with my Mazda 3 year 2004. Noone can help me at all !!! Even in Mazda they have no idea where is problem. For me it is at the moment only in cold weather. I cannot get throught immobilizer. After few turns it works, but not always (only when its bit warmer). I found out that if it is warmer, and I turn on ventilation for a while after it will let me go! Immobilizer starts flashing ... after few more minutes and turning key few times it will let me go !!! Please write me to [email protected] if you will know updates... I am desperate , cannot use my car in winter at all or cold weather. In summer works fine

Sep 18, 2008 | 2004 Mazda 3

Not finding what you are looking for?
2008 Infiniti FX35 Logo

584 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14832 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...