Question about 2001 Daewoo Lanos

Open Question

I start my car and place my foot on the aceleration pedal it just shut of like if it is not receiving any gas. what can possible be the problem? Could it be the VSS, or the ECA?

It give code Po342 and also code for the VSS

Posted by oricio martinez... on

Ad

1 Related Answer

roddoney

Rod Doney

  • 588 Answers

SOURCE: When I start my car, it run's for a aproximately five minutes and then engine just shut off. What can be the problem?

from from what I've just looked up it may be in the timing and possibly the cam sensor you may want to call up auto supply stores or pick up a manual

Posted on Mar 19, 2016

Testimonial: "Rod, just thinking on your anwser it make sense;I'll check on that and see how it work. Thank you so much."

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mi camioneta isuzu se apago corriendo y ya no prende la computadora mi marca un codigo po342 que puede ser el sensor de posicion de el arbol d levas se lo puse nuevo y siguio igual. que puede ser otra


please post in english his is USA forum. and is english only.
here ill use google translate for you.
My truck Isuzu no longer running and turn off the computer turns my marks a po342 code that may be the position sensor of the tree cam d put it back and continued the same. which can be another.

Ok , P0342 is clear in the book, (but you never said engine type in car>? so......)
here are the possibles.
1: CMP sensor dead or bad.
2: cam timing way off. (is compression TEST over 150 PSI on all cylinders? (no engine stated, so.... cant tell you why see?
3: bad wiring to the CMP.
4: or CMP timed wrong.

CMP is the name of the CAM SENSOR. BTW.
no car stated.
no year stated.
no engine stated
no country, yes, cars do vary greatly by , COUNTRY.
mostly hopeless so for...


use google translate to translate ENglish back to Spanish.

to do so type, Translate in the google box and magic happens.

Nov 30, 2014 | Isuzu Cars & Trucks

1 Answer

2000 Nissan Sentra Transmission


Hi....
if your car get a VSS code the Transmission control module.
Will command the Trans, in LIMP MODE.
Is mean you only will have 2 gear.
If you replaced the VSS sensor allready.
Maybe you have A electrical problem.
The First step is Check the condition of the VSS connector.
Remove the Connector and pull the wires a little each by each one.
To see if is broken inside of the Plastic cover.
IF you can
GIVE ME the Code number I will help you better.
Because is there more that One speed sensor on your trans..
Check the grounds on the Intake manifold, Black wire one of the wires is for the speed sensor.
The RED/YELLOW wire coming from the INSTRUMENT CLUSTER,
Is mean you need to check the Fuses that work with the instrument cluster. FUSE # 12 10amp, And # 30 10amp.
Located at fuse block left side of dash.
Is there a ground that work with the Cluster and Combination Meter. Behind left side of dash Black wire.
Check the Connection of the Cluster.

OK.. I hope this help on your problem.
Thank you for use fixya.

Aug 16, 2008 | 2000 Nissan Sentra

1 Answer

TRUCK HAS ROUGH IDLE AND WONT ACCELERATE


P0342 code indicates a defective cam angle position sensor (easily replaced).

Mar 16, 2014 | 1998 Isuzu Rodeo

1 Answer

Where is the Intermittent VSS Sensor Signal located on my 91 deville


You misunderstand code, there is a VSS (Vehicle Speed Sensor) it's problem is that it is giving an intermittent signal. The VSS is what tells the speedometer how fast you are going (among other things) it is located in the transmission (transaxle). '91 is right around the time when they were going away from mechanical speedometer cables so it may or may not have one depending on the production date. If it has a cable the VSS is built into the speedo gear housing. If there is no cable, the VSS is in the same location on the tranny it just has no provision to drive the speedo cable If you have the new part it may help you to find it on the car but it should be in the left side of the transmission housing near where the left drive axle goes into the case. The VSS gear actually drives off of the very end of that axle inside the gear case. I think it is a 10mm head bolt that retains the VSS.

Hope this helps, best of luck.

Jan 28, 2014 | 1992 Cadillac DeVille

1 Answer

1992 camaro, E-code (305tbi)- speedo inoperative,-gives code 24 no vss signal..-new vss installed, continuity good from vss to bulkhead connector and through to harness inside. there is supposed to be a...


Hi, I'm not familiar with the part, but the diagram shows it behind the glove box next to the ECM. Go in thru the bottom--remove the sound barrier, remove the EMC, then remove the buffer. What I recommend is to see if you can get one at a salvage yard. Otherwise, they are about $50 on eBay. Thanks for using FixYa.


jturcotte_1214.gifjturcotte_337.jpg

Mar 11, 2011 | 1992 Chevrolet Camaro

1 Answer

Trouble codes po335and po342 car runs fine but shows these trouble codes


P0335 - Crankshaft Position Sensor "A" Circuit
P0342 - Camshaft Position Sensor "A" Circuit Low Bank 1 or Single Sensor.

Click the code links above to access more information that pertains to the codes you posted.

Jul 06, 2010 | 1997 Pontiac Sunfire

1 Answer

Checked fault memory code po342


if its V6 it is in rear left head next to inlet manifold
plug must face rear of vehicle

Apr 29, 2009 | 2004 Isuzu Rodeo

1 Answer

ABS Light comes on and then Check engine light. Speedometer also isn't working


Does it give you a vss (vehicle speed sensor) code.If your vss is bad it will affect both the ABS and the speedometer.

Mar 05, 2009 | 2002 Jaguar X-Type

2 Answers

Check engine light reports VSS problem


A specific trouble code,no matter what the code is,always has a diagnostic route that is available at pay sources like All Data online.It always involves checking the wires involved in the specific circuit,for continuity,along with testing the individual components,like the vehicle speed sensor.Remove the VSS from the trans,and reinspect the drive,and driven gear.The drive gear is attached to the differential down in the trans,and you have to actually look down in the hole,and verify the drive gear is ok and intact.Then look very carefully at the plastic gear that is attached to the VSS,and make sure the middle of it isnt "applecored" as this will cause the VSS to NOT turn or give a signal.Now,reinstall the VSS,and turn the differential.This requires two helpers,one on each side of the car,to turn both tires at the same time,in the same direction (this turns the differential) while you are checking the two wires coming out of the VSS,for an alterenating current flow,that would be sent to the PCM(ECU).Verify VSS operation.If the VSS is producing a signal for the PCM,then the only thing left is the PCM itself,or the wires between the VSS,and PCM(ECU).That goes back to what i was saying about checking the wires' continuity between the sensor and PCM.Make certain the wires involved in the VSS circuit have continuity,and good tight connections at both ends.Good luck.

Jul 26, 2008 | 1996 Nissan 200SX

Not finding what you are looking for?
2001 Daewoo Lanos Logo

Related Topics:

250 views

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23822 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14868 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...