Question about Cadillac DTS

Open Question

How can I remove the gear shift knob? - DTS Cadillac Cars & Trucks

Posted by Willie Austin on

Ad

5 Related Answers

Anonymous

  • 85 Answers

SOURCE: removal of gear shift knob

There are two types of shift knobs. One that unscrews and one that the lower trim of the shift knob separates from the knob using a trim stick. After separating the lower trim from the knob pull upward to release the knob from the shift lever. If a new shifter assembly is being installed, unscrew the original shift knob or separate the lower trim from the knob and pull up to remove the knob from the shift lever. Screw the knob onto the new shifter assembly's lever no more than 14 turns or install the lower trim onto the shift lever then push the knob onto the shift lever and install the lower trim piece onto the shift knob.

Posted on Jul 03, 2008

Ad

Anonymous

  • 13 Answers

SOURCE: 1998 camaro, v6 automatic, gear shift knob ??

If it is neither suggestion by bunnydawg, try looking on the back of the shifter for a metal staple that needs to be pulled out.

Posted on Oct 30, 2008

Ad

Ron szarafinski

  • 217 Answers

SOURCE: I need to remove the gear shift knob on a 1993 Pontiac grand am

have to shift out of park engine off key on and their will be a pin or screw on the front side of gear shifter

Posted on Jan 17, 2009

Anonymous

  • 8 Answers

SOURCE: how to remove a 1996 gmc gear shift knob

i am going to go long on this... i believe you would pop out the center cap with the shift pattern using a small screwdriver, then locate a screw or bolt of some kind in there and remove it....

Posted on Mar 27, 2009

Anonymous

  • 1 Answer

SOURCE: Removing Factory Gear Shift Knob for 2001 Jetta

On my 2000 jetta glx, I had to replace both the shift knob and boot as one. It is built as one unit. You have to pull the boot up over the shift knob, break/bend a clip to "unlock" the shift knob then pull up. I hope the new knob you got has the boot built in and comes with a new clip.

Posted on Mar 27, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my ford freestyle gear indicator light how change it


Remove the PRNDL trim ring.
Remove the upper console panel.
Slide the lower shift knob bezel downward.
  1. Remove the bolt and lift up on the shift knob to remove.
Remove the lower shift knob bezel.
Disconnect the light bulb from the PRNDL bezel. an replace .

26002487-w0jffanovav232xjqcbliw5g-1-0.gif Don't think you need take shifter knob off . Just PRNDL trim plate an upper console plate . They should just pull up , use plastic trim tool to get it so you can get your fingers under an pull up carefully .

26002487-w0jffanovav232xjqcbliw5g-1-2.gif PRNDL trim plate

26002487-w0jffanovav232xjqcbliw5g-1-5.gif Light blub connector !

26002487-w0jffanovav232xjqcbliw5g-1-9.gif

Dec 11, 2015 | 2006 Ford Freestyle

3 Answers

How do I relplace gear shift?


If you have a stick shift ( floor shift) remove the boot around the gear stick and the insulation on the floor to reveal the 4 bolts that hold the shift turret on to the top of the box. Undo the bolts and lift the gear lever assembly out of the gear box.

May 30, 2014 | 2001 Oldsmobile Alero

1 Answer

2005 Impala gear shift button popped out. I have to put it back in each time I need to shift to D, R, etc. How can I remedy this problem without replacing the whole gearshift?


Re-attaching the knob to the gearshift is the key...Look for a hole on the lower section of the knob...if you cannot see it...remove the bottom chrome piece from the knob, (pry apart carefully not to scratch the chrome housing...you should see the small hole normally includes a small allen insert screw or Phillips screw...must be screwed in to the gear shift shaft to hold in place...if you cannot compare...visit a local salvage yard to experiment..."Pic A Part" is a national self help salvage yard. Hope this helps. If the button does not stay in the gear shift knob...you can replace the knob (with button) only...remove the knob as described above. Hope this helps.

Oct 14, 2013 | 2006 Chevrolet Cobalt

1 Answer

Replace gear shifter knob on s-10 manuel


Most gear shift knobs are just screwed on. Try turning it anti clockwise if yu can not see any screw holding it

Jun 22, 2012 | Cars & Trucks

1 Answer

The gear shift gets stuck and won't shift into other gears.Will put it reverse and then try to put in drive and it gets stuck in reverse.


Either the shift knob or the actuator rod under the shift knob has worn out.
Remove the shift knob and pull the actuator rod (plastic) out of the shift lever and inspect it for wear or damage. If the rod is not worn or damaged, replace the shift knob and you will be good to go.
Good luck.

Nov 11, 2009 | 1997 Pontiac Grand Prix

1 Answer

Gear shifter will not go into park


There is a plastic actuator stick under the shift knob. Remove the "horse shoe" clip from the shift knob and remove knob by pulling strait up. You can twist it right and left a very small amount to loosen the knob, but not much.
Once you have the shift knob removed you will see the plastic actuator stick. Push down on the stick and put shift lever in park. If that works, the shift knob or stick is worn out.
Let me know.
Regard,

Feb 12, 2009 | 2004 Pontiac Grand Am

1 Answer

Removing Factory Gear Shift Knob for 2001 Jetta


On my 2000 jetta glx, I had to replace both the shift knob and boot as one. It is built as one unit. You have to pull the boot up over the shift knob, break/bend a clip to "unlock" the shift knob then pull up. I hope the new knob you got has the boot built in and comes with a new clip.

Jan 08, 2009 | 2000 Volkswagen Jetta TDI

1 Answer

Unable to put back on the gear shift knob on my car after removing it.


year, make and model of the vehicle in question....?¿?¿?

Oct 18, 2008 | 1999 Dodge Intrepid

1 Answer

Removal of gear shift knob


There are two types of shift knobs. One that unscrews and one that the lower trim of the shift knob separates from the knob using a trim stick. After separating the lower trim from the knob pull upward to release the knob from the shift lever. If a new shifter assembly is being installed, unscrew the original shift knob or separate the lower trim from the knob and pull up to remove the knob from the shift lever. Screw the knob onto the new shifter assembly's lever no more than 14 turns or install the lower trim onto the shift lever then push the knob onto the shift lever and install the lower trim piece onto the shift knob.

Jul 02, 2008 | 2007 Dodge Magnum SRT8 Wagon

1 Answer

2002 VOLVO S60 automatic


I want to change the boot on my 2003 Pasatt..It seems to be connected to the gear shift knob...How do I get the knob off ??

Jun 29, 2008 | 2002 Volvo S60

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,006 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...