Question about 1996 Cadillac DeVille

Open Question

On a 1996 Cadillac, where is the input turbine sensor located

Where is the turbine input sensor located on the transmission

Posted by Anonymous on

Ad

5 Related Answers

JShreader

JShreader

  • 50 Answers

SOURCE: O2 Sensor on a 1996 Cadillac Eldorado

Hello mrsalbert, my name is JShreader. Thank you for choosing fixya.com

Depending on which oxygen sensor you are looking for...there are several of them throughout the Exhaust System. I will start out by giving you a brief description of what and oxygen sensor is, and they're general purpose.

DESCRIPTION
Four Heated Oxygen Sensors (HO2S) are mounted in the exhaust system where they monitor the oxygen content in the exhaust stream. There is an oxygen sensor mounted in each exhaust manifold and one on each end of the catalytic converter. the oxygen sensor located in the front exhaust manifold is the Bank 2 Sensor 1 (Front) sensor. The oxygen sensor located in the rear exhaust manifold is the Bank 1 Sensor 1 (Rear) sensor. The oxygen sensor located in the Y-pipe ahead of the catalytic converter is the Bank 1 Sensor 2 (Pre-converter) sensor. The oxygen sensor located in the catalytic converter outlet is the Bank 1 Sensor 3 (Post-converter) sensor.

OPERATION
An oxygen sensor acts like a battery because it creates its own signal voltage once it reaches operating temperature. This voltage is produced when the oxygen content in the exhaust stream is different than the oxygen content in the atmosphere. A lean condition (high oxygen content in exhaust) will produce a low voltage (near 0 volts) and a rich condition (low oxygen content in exhaust) will produce a high voltage (near one volt). The PCM provides a reference signal voltage (0.45 volt) and a ground to the sensor. The PCM reference voltage is necessary because the oxygen sensors do not provide their own voltage until they reach operating temperature.

HEATING ELEMENT
the oxygen sensors also incorporate a heating element inside of the sensor housing. This heating element is energized with the ignition On and allows the sensors to reach operating temperatures quickly. The PCM can then use oxygen sensor information sooner after engine start-up.

PCM INPUTS
The PCM uses oxygen sensor information during Closed Loop operation to constantly adjust fuel control to reduce exhaust emissions. Because the oxygen sensors provide information sooner after engine start-up, exhaust emissions are reduced. Faulty oxygen sensors will cause various driveability conditions and will set a DTC.

That being said...I uploaded a .pdf for you of pictures showing the locations of ALL the oxygen Sensors on your Vehicle. You can download it by clicking HERE.

I hope this helps you. If you have any more questions or need any more diagrams, please don't hesitate to ask...Thanks again, JShreader!

Posted on Apr 01, 2009

Ad
Keith100881

Dennis Saunders

  • 74 Answers

SOURCE: O2 Sensor on a 1996 Cadillac Eldorado

you have 4 o2 sensors on the new one 2 in front of catylitic converter and 2 after on the exhaust

Posted on May 24, 2009

Ad

Anonymous

  • 490 Answers

SOURCE: Please describe the location of Transmission Speed

Look on the left side of the transmission.

Posted on Aug 05, 2009

brandon day

  • 173 Answers

SOURCE: where is the knock sensor on a cadillac sedan

located underneath the intake manifold remove it and disconnect the knock sensor unscrew the knock sensor. installation is reverse

Posted on Apr 05, 2010

Jesse Harmon

  • 104 Answers

SOURCE: 1996 Cadillac Deville overheating. Bought a new

Not sure of the location of it. Usually they are in the thermostat housing or on the top of the engine. Maybe on one side of a cylinder head. You may also replace the thermostat itself and make sure your cooling fans are working properly

Posted on Oct 02, 2010

Testimonial: "i found it and of course on the 4.6L its at the back of the engine underneath the EGR stuff making it a pain in the *** to get at and replace"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 1996 Cad. Deville, where is the tubine speed sensor located?


press the helpful button and follow me on fixya for more tips
Input speed sensor is located inside the transmission. The sensor is located next to the sprocket for the input shaft. The sensor is held in place with 2 6mm bolts, one for the sensor, one for the wiring harness.

Input Speed Sensor P0717 Replacement

P0717 ISS Speed Sensor Code Cadillac Deville Eldorado Seville Fleetwood...

Vehicle Speed Sensor Removal Installation

Feb 01, 2016 | Cars & Trucks

1 Answer

Where does the turbine input shaft speed sensor go on a 2010 cevy malibu Lt


Chances are that this sensor is located in the transmission or has access to it outside the housing.Take the car to a transmission specialist and have them give you an estimate.Most dealerships these days don't even do trany work anymore so save yourself some money and go directly to someone who can help you.good luck

May 22, 2014 | 2010 Chevrolet Malibu

1 Answer

I need help asap 2003 Expedition code p0171 and code p0712 i have and idea of the 1st code but whats the secound code i really need help i dont want to take it to a shop where there going to charge me alot...


P0700 Transmission Control System

P0701 Transmission Control System Range/Performance

P0702 Transmission Control System -Electrical

P0703 Torque Converter/Brake Switch B Circuit

P0704 Clutch Pedal Position Switch -Circuit Malfunction

P0705 Transmission Range Sensor/Switch Circuit Malfunction (PRNDL Input)

P0706 Transmission Range Sensor/Switch Circuit Range/Performance

P0707 Transmission Range Sensor/Switch Circuit Low Input

P0708 Transmission Range Sensor/Switch Circuit High Input

P0709 Transmission Range Sensor/Switch Circuit intermittent

P0710 Transmission Fluid Temperature Sensor Circuit

P0711 Transmission Fluid Temperature Sensor Circuit Range/Performance

P0712 Transmission Fluid Temperature Sensor Circuit Low Input

P0713 Transmission Fluid Temperature Sensor Circuit High Input

P0714 Transmission Fluid Temperature Sensor Circuit Intermittent

P0715 Input/Turbine Speed Sensor Circuit

P0716 input/Turbine Speed Sensor Circuit Range/Performance

P0717 Input/Turbine Speed Sensor Circuit No Signal

P0718 Input/Turbine Speed Sensor Circuit Intermittent

P0719 Torque Converter/Brake Switch B Circuit Low

P0720 Output Shaft Speed Sensor Circuit

P0721 Output Shaft Speed Sensor Circuit Range/Performance

P0722 Output Shaft Speed Sensor Circuit No Signal

P0723 Output Shaft Speed Sensor Circuit Intermittent

P0724 Torque Converter/Brake Switch B Circuit High

P0725 Engine RPM Input Circuit

P0726 Engine RPM Input Circuit Range/Performance

P0727 Engine RPM Input Circuit No Signal

P0728 Engine RPM Input Circuit Intermittent

P0729 Gear 6 Incorrect Ratio

P0730 Incorrect Gear Ratio

P0731 Gear 1 Incorrect Ratio

P0732 Gear 2 Incorrect Ratio

P0733 Gear 3 Incorrect Ratio

P0734 Gear 4 Incorrect Ratio

P0735 Gear 5 Incorrect Ratio

P0736 Reverse Incorrect Ratio

P0737 TCM Engine Speed Output Circuit

P0738 TCM Engine Speed Output Circuit Low

P0739 TCM Engine Speed Output Circuit High

P0740 Torque Converter Clutch Solenoid Circuit

P0741 Torque Converter Clutch Solenoid Circuit Performance or Stuck Off

P0742 Torque Converter Clutch Solenoid Circuit Stuck On
P0743 Torque Converter Clutch Solenoid Circuit Electrical
Now i dont know a lot about automatics especially modern ones with all this fancy electronics thats used nowdays but i think its a fault with the temperature sensor for the gearbox.But where its located and what it looks like i have no idea it could even be mounted inside the gearbox .Sorry not a very good answer from a mechanic but?? very few of our europeon cars come with auto transmission .Evan when i do know whats wrong i cannot buy the parts for the gearbox as only re-con boxes supplied by the dealer so best advice is to try a specialist in auto box repairs only .PS some of my best students when i used to teach mechanics many moons ago were the girls so no excuses like iam only a girl please

Apr 22, 2013 | Cars & Trucks

1 Answer

2000 ford explorer input turbine speed sensor. code po715 was pulled on the obd scanner.does any 1 no were this sensor is located at on my transmission, i beleiv e it has the 55r5e trans but not quit sure....


the is also known as sensoer c it is your pressure control solenoid. if you drop the transmission pan and remove the transmission filter it is on the side of the valve body. DO NOT REMOVE THE VALVE BODY PLEASE12_7_2012_2_21_36_am.gif

Dec 07, 2012 | 2000 Ford Explorer

1 Answer

Were is the input turbine speed sensor located at,and what does it look like.


The turbine shaft speed sensor is located inside the transmission. The transmission will have to be removed and disassembled to access the sensor. The sensor you have now... sound about what it looks like.

Dec 07, 2012 | 2000 Ford Explorer

1 Answer

Need to get the location of vehicle speed sensor on a 1996 cadillac deville 4.6


1996 Cadillac De ville 4.6 Location for vehicle speed sensor it is at the transmission output shaft housing (the one near the rear of the transmission by the driveshaft)

Apr 30, 2011 | Cadillac DeVille Cars & Trucks

2 Answers

Check engine code PO715


Transmission Input Speed Sensor (G182 VAG com code): Circuit Malfunction
The Input Turbin Speed Sensor is located inside the transmission, the code can be caused by a failed sensor or sensor wiring or a slipping transmission.

Jan 16, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

1996 cadillac deville is displaying code pc 0717 can someone tell me want this is?


P0717 Input/Turbine Speed Sensor Circuit No Signal
The system uses a reluctor wheel and a magnetic sensor to aide in shift patterns. If the sensor wiring, sensor or wheel inside the transmission become damaged, it can trigger this code. This should be looked at by a trusted transmission tech in your area. Cadillac does some wierd thing things when it comes to placement, wiring and repiar. Get someone who knows Cadillac to get this done for you. It will save you a lot of heart ache and cursing at the car. Hopefully it will just be a bad sensor, and you will be back out on the road in just a afternoon. Let me know if you need anything else or wish to tackle it yourself. I think I can find some instructions.

Sep 22, 2010 | 1996 Cadillac DeVille

1 Answer

I have a Volkswagen TDI 1.9L - diagonistic fault shown on OBD2 tool is P0715 - Input/Turbine Speed Sensor Circuit Malfunction Please advise how I can get this fixed ?


That code also reads as: Transmission Input Speed Sensor (G182): Circuit Malfunction

The sensor is located inside the transmission. Not exactly a DIY type of job...

Jun 28, 2009 | 2001 Volkswagen Jetta TDI

4 Answers

I have a code p0715, which is the input turbine speed sensor


The input/turbine speed sensor has nothing to do with the turbo. It is transmission related and is a circuit malfunction. I am having the same problem and it causes my car to downshift into 3rd gear (computer's fail safe gear) on the highway. The sensor is located above the transmission housing, and doesn't require you to take apart the tranny. I am having trouble finding the part number for this and where to buy it. Any help would be nice.

Dec 26, 2008 | 2002 Mitsubishi Lancer

Not finding what you are looking for?
1996 Cadillac DeVille Logo

Related Topics:

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...