Question about Cars & Trucks

1 Answer

P1116 O2S Sensor Heater Circuit Open Bank 1 Sensor 1 How do I fix it?

Posted by Cheryl on

Ad

1 Answer

Bogdan Odwazny

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 6,158 Answers

HAVE TO REPLACE SENSOR.

Posted on Jan 31, 2016

Ad

5 Related Answers

Anonymous

  • 5 Answers

SOURCE: Ford Windstar 1996 Trouble Codes P0171, P0141, P0161, and P0174

Bank one is toward the front of the vehicle. Sounds like the heated oxygen sensors have gone bad. The Oxygen Sensors are located in the exhaust pipe and require a special socket to remove and replace.

Posted on Jan 16, 2009

Ad
warlock61

warlock61

  • 659 Answers

SOURCE: more 99 cougar problems

there is a fuse for the o2 heaters if one of the sensors blew the fuse they will all be out

Posted on Mar 01, 2009

Susan Price

  • 1857 Answers

SOURCE: Code p0141 02 Sensor Heater Circuit Malfunct Bank #1 Sensor2

after the catalytic converter on the driver side in the exhaust pipe.

Posted on Jul 07, 2010

Testimonial: "Awesome info. Thanks!"

SOURCE: air fuel sensor heater circuit

air fuel sensor heater circuit response malfuction

Posted on Oct 09, 2010

jturcotte

Jeffrey Turcotte

  • 8984 Answers

SOURCE: check engine light P0031 code,

sensor one is before the converter. Sensor 2 is after the converter. :o)

Posted on Dec 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i fix a code p0134 for my 1999 infintiy i30


code p 0134 refers to heated oxygen sensor(HO2S) 1 bank 1--no activity detected ===causes wiring open circuit ---heating inoperative ---HO2S Sensor
also refers to oxygen sensor (O2S) --no activity detected ===causes --- wiring---O2S
the HO2S is in the exhaust manifold before the cat converter
the O2S is after the cat converter
check the wires and connections , then replace either or both sensors

Oct 22, 2016 | Cars & Trucks

1 Answer

Have code P2238 - what could be the cause ?


code p 2238 has 3 references
heated oxygen sensor(HO2S) 1 bank 1,positive current control---circuit low ====causes ---wiring short to ground ---HO2S
second reference
oxygen sensor (O2S) 1 bank 1 positive current---circuit low====causes ---wiring short to ground ---O2S
3rd reference
HO2S 1 bank 1--implausible signal===causes ---wiring---short to positive ---short to ground ---HO2S---ECM
as the heated oxygen sensor is common with wiring problems indicated , maybe changing it will fix the code
note
HO2S is the sensor in the exhaust manifold in bank1 before the cat converter

Oct 13, 2016 | 2003 Toyota Tundra

1 Answer

P1884 code 2005suzuki forenza P0420 P0134 P0138


code p 420 refers to cat converter system , bank 1--efficiency below threshold ===causes ---cat converter faulty---wiring --heated oxygen sensor (HO2S), 2 faulty
code p 0134 refers to HO2S 1 bank 1-no activity detected ===causes --wiring open circuit -- heating inoperative --- HO2S
also refers to oxygen sensor ( O2S) 1 bank 1--no activity detected == causes wiring ---O2S
code p 0138 refers to HO2S 2 bank 1--high voltage === causes ---wiring short to positive ---HO2S--- ECM
also refers to O2S 2 bank 1 high voltage === wiring short to positive O2S -- ECM
I do not have a listing for code p 1338 but I suspect that it will refer to the other codes in some way
first fix is to check the cat converter is operational ( not cracked and blocking the exhaust system)
next replace the HO2S sensor ( one before the cat converter ) and then the O2 sensor (the one after the cat converter)
all the codes will relate to problems in that area

Sep 01, 2016 | 2005 Suzuki Forenza

1 Answer

Will not start p2045 p2197 p0190 p2247 p2245 p2248 p2249 p2518 comes up


code p2045 refers to reductant temperature sensor--high input==causes --wiring faulty sensor
code p2197 refers to heated oxygen sensor(HO2S)1 bank 2-- signal stuck lean===causes HO2S---fuel pressure---injectors---intake leak
also refers to oxygen sensor (O2s)1 bank 2 -signal stuck lean===causes--O2S--fuel pressure---injectors---intake leak
also refers to heated oxygen sensor (HO2S) 1 bank 2--implausible signal===causes wiring---short to ground--short to positive--HO2S---ECM
code po190 refers to fuel rail pressure (FRP) sensor-circuit malfunction===causes --wiring ---fuel rail pressure sensor---ECM
code p2247 refers to heated oxygen sensor (HO2s) 1 bank 1 reference voltage--open circuit===causes--wiring ---ho2s
also refers to o2s 1 bank 2 reference voltage ---open circuit===causes wiring---o2s
also refers to HO2S 1 bank 2 ---no signal===causes wiring--ho2s---ECM
code p2245 refers to HO2S 1 bank 1 --reference voltage --circuit low===causes--wiring short to ground--ho2s also refers to o2s 1 bank 1 circuit low===causes wiring short to ground--o2s
code p2248 refers to the ho2s I bank --performance problem===causes --wiring--ho2s
code p2249 has the same causes short to ground---ho2s and o2s
code p2518 refers to a/c refrigerant pressure sensor B ---circuit high===causes wiring short to positive--a/c refrigerant pressure sensor.
so after all that replace all the ho2s and o2s sensors using the correct tools so that the wiring is not damaged and check the wiring back to the ECM for burns and rub marks.

Dec 30, 2013 | Cars & Trucks

1 Answer

P2237 code


code p2237 refers to heated oxygen sensor(HOS2) 1 bank 1-positivecurrent control-open circuit ---or oxygen sensor(O2S)1 bank 1-open circuit--- or heated oxygen sensor1 bank 1 -no signal=== causes for all three is wiring--HOS2----wiring O2S---wiring--HO2S---ecm. Basically I would be looking for a disconnected wire or broken wire to the sensors.

Jul 23, 2013 | Cars & Trucks

1 Answer

I have p044 code for Camry 2004


P0044 - HO2S Heater Control Circuit High (Bank 1 Sensor 3)

The P0044 is set when the ECM detects an excessively high voltage through the heated oxygen sensor heater circuit

Oxygen Sensors (O2S) or Heated Oxygen Sensors (HO2S) need to reach a minimum operating temperature of 750 degrees F to produce an accurate voltage signal. The faster the heated oxygen sensor reaches that temperature the faster the sensor will start sending an accurate signal to the Engine Control Module (ECM).

In order to achieve the require temperature, a heater element is included inside the heated oxygen sensor. The ECM controls the heated oxygen sensor heater element based on signals from the engine coolant temperature and engine load. The ECM controls the heater element circuit by allowing current flow to ground.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 circuit open shorted to ground
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 circuit poor electrical connection
- Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 circuit
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 circuit fuse
- Faulty Engine Control Module (ECM)

The ECM monitors the voltage signal received through the heater element circuit and determines the state of the circuit by comparing the voltage detected with the factory specifications.

zjlimited_245.gif

Hope helps (remember to rate this answer).

Mar 15, 2011 | 2004 Toyota Camry

2 Answers

The engine light and VSC light are on (Vehicle Singapore 2004 Lexus RX 300. Diagnostics report Error code P0037


your o2 sensor is bad. vsc will go on for any small DTC displayed on the MIL (cel)

P0037 LEXUS P0037 LEXUS - Oxygen Sensor Heater Control Circuit Low Bank 1 Sensor 2 Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
Possible causes - Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit open shorted to ground
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit poor electrical connection
- Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit fuse
- Faulty Engine Control Module (ECM) When is the code detected? The P0037 is set when the ECM detects an excessively low voltage through the heated oxygen sensor heater circuit P0037 LEXUS Description Oxygen Sensors (O2S) or Heated Oxygen Sensors (HO2S) need to reach a minimum operating temperature of 750 degrees F to produce an accurate voltage signal. The faster the heated oxygen sensor reaches that temperature the faster the sensor will start sending an accurate signal to the Engine Control Module (ECM).

In order to achieve the require temperature, a heater element is included inside the heated oxygen sensor. The ECM controls the heated oxygen sensor heater element based on signals from the engine coolant temperature and engine load. The ECMcontrols the heater element circuit by allowing current flow to ground.

The ECM monitors the voltage signal received through the heater element circuit and determines the state of the circuit by comparing the voltage detected with the factory specifications.

o2_heater_circuit.gif

Mar 14, 2011 | 2004 Lexus RX 330

1 Answer

CODE PO155 BANK2 SENSOR 1 WHERE IS THIS SENSOR LOCATED?


A code P0155 may mean that one or more of the following has happened:
* O2 Heater element resistance is high
* Internal short or open in the heater element
* O2 heater circuit wiring high resistance
* open or short to ground in the wiring harness

Possible Solutions:
* Repair short or open or high resistance in wiring harness or harness connectors
* Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)


Oxygen sensors are always numbered like this:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2

Some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.

Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.

Hope helps (remember to rate this).

Oct 02, 2010 | 2002 Mitsubishi Montero

1 Answer

Where Are The sensor Banks On The 2004 GC


Grand Cherokee oxygen sensor locations for 4.0 and 4.7 engines

510d5d9.jpg


f8b5293.jpg


Four wires (circuits) are used on each O2 sensor:

  • 12–volt feed circuit for the sensor heating element
  • Ground circuit for the heater element
  • Low-noise sensor return circuit to the PCM
  • Input circuit from the sensor back to the PCM to detect sensor operation

O2S Sensor removal Never apply any type of grease to the oxygen sensor electrical connector, or attempt any soldering of the sensor wiring harness.
WARNING: THE EXHAUST MANIFOLD, EXHAUST PIPES AND CATALYTIC CONVERTER(S) BECOME VERY HOT DURING ENGINE OPERATION. ALLOW ENGINE TO COOL BEFORE REMOVING OXYGEN SENSOR.
1. Raise and support vehicle.
2. Disconnect O2S pigtail harness from main wiring harness.
3. If equipped, disconnect sensor wire harness mounting clips from engine or body.
CAUTION: When disconnecting sensor electrical connector, do not pull directly on wire going into sensor.
4. Remove O2S sensor with an oxygen sensor removal and installation tool.

02S Sensor installation
Threads of new oxygen sensors are factory coated with anti-seize compound to aid in removal. DO NOT add any additional anti-seize compound to threads of a new oxygen sensor.
1. Install O2S sensor. Tighten to 22 ft. lbs. (30 N·m) torque.
2. Connect O2S sensor wire connector to main wiring harness.
3. If equipped, connect sensor wire harness mounting clips to engine or body. When Equipped: The O2S pigtail harness must be clipped and/or bolted back to their original positions on engine or body to prevent mechanical damage to wiring.


Hope thats help (remember comment and rated this).

Apr 29, 2010 | 2004 Jeep Grand Cherokee

1 Answer

I have 8000 miles on my Tucson check engine light came on at start up this morning...gas cap is tight...no problems?????


there are over 200 reasons for the check engine light to come on, the gas tank cap is just one of them, this light and the problem that turned it on are most likely covered under the federal emission warranty, contact the dealer. see trouble code list below for some of the probelems that cause a check enghine light.
P1100 Map Sensor - Malfunction
P1101 Map Sensor - Abnormal
P1102 Map Sensor - Low Input
P1103 Map Sensor - High Input
P1104 Air Flow
P1105 Air Flow - Abnormal
P1106 Air Flow - Low Input
P1107 Air Flow - High Input
P1108 Fuel Pump
P1109 Fuel Pump - Abnormal
P1110 Fuel Pump - Stuck On
P1110 ETS System - Malfunction
P1111 Fuel Pump - Electrical
P1112 Manifold Differential Pressure Sensor
P1112 VGT Actuator - Malfunction
P1113 Manifold Differential Pressure Sensor - Abnormal
P1114 Manifold Differential Pressure Sensor - Low
P1115 Coolant Temperature Input - Abnormal
P1116 Boost Pressure Sensor - Malfunction
P1118 ETS Motor - Malfunction
P1119 Inlet Metering Valve Control
P1120 Electric Governor - Malfunction
P1120 Inlet Metering Valve Malfunction
P1121 APS PWM Output Circuit Malfunction
P1121 Throttle Position Input - Abnormal
P1122 Boost Pressure Control Valve
P1123 Fuel System Rich - Idle
P1123 Timer Position Sensor - Malfunction
P1124 Fuel System Lean - Idle
P1125 Fuel Press Sensor1
P1126 Fuel Press Sensor2
P1127 Fuel System Rich - Part Load
P1127 Control Sleeve Position Sensor
P1128 Fuel System Lean - Part Load
P1130 Start Solenoid- Malfunction
P1131 Injection Quantity Adjust
P1134 O2s Transition Time(B1/S1)
P1135 Injection Timing Servo
P1140 Inlet Air Temperature Sensor Malfunction
P1141 Slow Duty Solenoid- Malfunction
P1145 Main Duty Solenoid- Malfunction
P1146 Idle Co Potentiometer
P1147 Accelerator Position Sensor (ETS) Circuit
P1150 Barometric Pressure Sensor Malfunction
P1151 Accelerator Position Sensor (EMS) Circuit
P1152 Accelerator Position Circuit-Low Input
P1153 Accelerator Position Circuit-High Input
P1154 O2s Transition Time(B2/S1)
P1155 Limp Home Valve- Malfunction
P1159 Variable Induction System
P1162 High Pressure Pump & Fuel Line
P1166 O2s (B1) Control Adaptation
P1166 Limit O2s Lambda Control (B1)
P1167 O2s (B2) Control Adaptation
P1167 Limit O2s Lambda Control (B2)
P1168 O2s (B1/S2) Heater Power
P1169 O2s (B2/S2) Heater Power
P1170 ECM (Barometric Pressure Sensor)
P1171 ETS Valve Stuck - Open
P1172 ETS Improper Motor Current
P1173 ETS Target Following Malfunction
P1174 ETS Valve Stuck - Close #1
P1175 ETS Valve Stuck - Close #2
P1176 ETS Motor Open/Short #1
P1177 ETS Motor Open/Short #2
P1178 ETS Motor Power - Open
P1179 ETS Position F/B-Mismatch
P1180 O2 S1 Heater Circuit- Malfunction
P1180 Fuel Pressure Regulator - Malfunction
P1181 Fuel Pressure Monitoring
P1182 O2 S2 Heater Circuit - Malfunction
P1182 Fuel Pressure Regulator - Short
P1183 Fuel Pressure Regulator - Open
P1184 O2s No Activity (B1/S2)
P1184 Fuel Pressure Regulator - Power
P1185 Fuel Position - Excessive
P1186 Fuel Pressure - Too Low
P1187 Regulator Valve - Stuck
P1188 Fuel Pressure - Leakage
P1189 Governor Deviation
P1190 Intake Throttle Actuator
P1191 ETS Limp Home Valve On
P1192 Limp home - Target Follow Malfunction
P1193 ETS Limp Home - Low Rpm
P1194 Limp Home - TPS2 Position Malfunction
P1195 Limp Home - Target Follow Delay
P1196 ETS Limp Home - Close Stuck
P1300 Spark Timing Adjust Signal
P1300 Injector Specific Data Fault
P1300 Synchronization Error-CKP/CMP
P1301 TDC Sensor - Abnormal
P1302 TDC Sensor - Low Input
P1303 TDC Sensor - High Input
P1304 Phase Sensor
P1305 Phase Sensor - Abnormal
P1306 Phase Sensor - Low Input
P1307 Phase Sensor - High Input
P1307 Accelerator Sensor - Range/Performance
P1308 Ignition Coil.1
P1308 Accelerator Sensor - Low
P1308 Accelerator Sensor Circuit - Low
P1309 Ignition Coil.1 - Abnormal
P1309 Accelerator Sensor - High
P1309 Accelerator Sensor Circuit - High
P1310 Ignition Coil.1 - Low Output
P1310 Injection Control Circuit Fault
P1311 Ignition Coil.1 - High Output
P1312 Ignition Coil.2
P1313 Ignition Coil.2 - Abnormal
P1314 Ignition Coil.2 - Low Output
P1315 Ignition Coil.2 - High Output
P1316 Ignition Coil.3
P1317 Ignition Coil.3 - Abnormal
P1318 Ignition Coil.3 - Low Output
P1319 Ignition Coil.3 - High Output
P1320 Ignition Coil.4
P1321 Ignition Coil.4 - Abnormal
P1321 Glow Indicator Lamp - Short
P1322 Ignition Coil.4 - Low Output
P1322 Glow Indicator Lamp - Open
P1323 Ignition Coil.4 - High Output
P1324 Glow Relay - Malfunction
P1325 Glow Relay - Abnormal
P1325 Glow Relay
P1326 Glow Relay - Stuck On
P1326 Glow Relay - Short
P1327 Glow Relay - Electrical
P1327 Glow Relay - Open
P1330 Spark Timing Adjust Signal
P1331 #1 MF Signal Line Short
P1332 #2 MF Signal Line Short
P1333 #3 MF Signal Line Short
P1334 #4 MF Signal Line Short
P1335 #5 MF Signal Line Short
P1336 #6 MF Signal Line Short
P1337 #7 MF Signal Line Short
P1338 #8 MF Signal Line Short
P1340 IFS 2 Open

Jun 16, 2009 | 2006 Hyundai Tucson

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

23424 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...