Front monitor works normal but two rear sear monitors don't work no audio or video what seems to be the issue?

A scan should reveal a monitor issue

The chimes an turn signal noise come out driver door speaker . Both front speakers not working could be a blown circuit fuse inside the radio or just blown front speaker channel . Your best bet , take it to a GM dealer or someother qualified repair shop . You have no idea of the complexity of this . The radio can set DTC'S - diagnostic trouble codes , believe it or not !
DTC B1025, B1035, B1045, or B1055
DTC B1025 01: Audio Output 1 Left Front Circuit Short to Battery
DTC B1025 02: Audio Output 1 Left Front Circuit Short to Ground
DTC B1035 01: Audio Output 2 Right Front Circuit Short to Battery
DTC B1035 02: Audio Output 2 Right Front Circuit Short to Ground
DTC B1045 01: Audio Output 3 Left Rear Circuit Short to Battery
DTC B1045 02: Audio Output 3 Left Rear Circuit Short to Ground
DTC B1055 01: Audio Output 4 Right Rear Circuit Short to Battery
DTC B1055 02: Audio Output 4 Right Rear Circuit Short to Ground

Each of the audio output channel circuits (+) and (-), at the radio and audio amplifier have a DC bias voltage that is one half of the battery voltage. When using a DMM, each of the audio output channel circuits will measure approximately 6.5V DC. The audio being played on the system is produced by a varying AC voltage that is centered around the DC bias voltage on the same circuit. The AC voltage is what causes the speaker cone to move and produce sound. This voltage will vary depending on what type of audio is being listened to, talk or music, and type of music, as well as the volume setting of the system. Low volume and talk settings will measure around 1V AC and less, where constant music may measure 3V AC and slightly higher.
DTC B1287 01: Amplifier Control Signal Circuit Short to Battery
DTC B1287 02: Amplifier Control Signal Circuit Short to Ground
DTC B1287 04: Amplifier Control Signal Circuit Open

The radio provides a remote amplifier mute output circuit to control overall muting of the remote amplifier. The amplifier receives pulse width modulated (PWM) signals on the control circuit at varying duty cycle percentages for controlling muted and unmuted functions of the amplifier. Circuitry internal to the radio monitors the remote amplifier mute circuit for faults and sets the appropriate DTC when faults are detected.

FUSE...RELAY...CIRCUIT BREAKER...OR WIRING! WITH REAR WIPER SQUITER SWITCH ENGAGED,,,CHECK FOR VOLTAGE AT HARNESS CONNECTOR

change the resolution settings then i ll work properly :)

The converter is 13 years old

It won't be too effective by now,
so you may want to consider replacing it

First have a repair shop check your O2 Sensors

The front ones get replaced at 100,000 miles

The rear ones are your Monitor ones you have
an issue with. They may be shot by now

Don't always need a MIL Lamp on dash to have
worn out parts

PO 302-- misfire on cylinder #2

PO160- O2 Sensor (Bank 2 Sensor 2)
The rear O2 sensor is a converter monitor
and don't do much or fail often,but yours
may have. More of an indication your exhaust
converter is failing,if sensor tests okey

PO720- is a Tranmission Output Speed Sensor

I would find the & solve the ignition misfire issue first.

Then replace both front O2 Sensors, if you have two &
they have never been done or have 100,000 miles on them

Next scope the rear sensors to see if they even work,as you have a code

All Automatic Transmissions and Power Steering MUST have
their fulids changed EVERY 30,000 miles or you Will have failure

Your trans code will need to be diagnosed after the other issues
are resolved if it is still there.

Check for disconnected ABS sensors. The front sensors in the front are located next to the axle shafts. The rear sensor is located on the rear differential housing itself on top, in the middle. The ABS is monitored by the computer for performance. The ABS kicks on when the vehicle comes from a certain speed to a dead stop, keeping the wheels from locking up. That could be the reason for the speedometer not working. Or it could be a bad speed sensor. Both can also trigger the check engine light because it is monitored by the computer. The brake light usually comes on due to low fluid level. It can trigger the light, but not be low enough to impact brake performance. I hope this helps.

Depends on what model and components you have:

{ ...
ENGINE TORQUE DISTRIBUTION – DIRECTING THE FLOW OF POWER
In an all-wheel-drive vehicle, engine power can be directed to all four wheels. Subaru Symmetrical AWD differs slightly from model to model in how it directs power to the wheels, depending on its transmission.

MODELS WITH FIVE-SPEED MANUAL TRANSMISSION – CONTINUOUS ALL-WHEEL DRIVE: A viscous-type locking center differential and limited-slip rear differential help distribute torque – normally configured at a 50/50 split front to rear. If wheel speed differs between front and rear axles, the center and/or rear differentials lock up to help distribute power to the wheels with the most traction.

MODELS WITH FOUR-SPEED AUTOMATIC TRANSMISSIONS – ACTIVE ALL-WHEEL DRIVE: An electronically controlled variable transfer clutch and limited-slip rear differential distribute power to where traction is needed. Sensors monitor parameters such as wheel slippage, throttle position, and braking to help determine torque distribution and direct it to the wheels with optimum traction.

MODELS WITH FIVE-SPEED AUTOMATIC TRANSMISSION – VARIABLE TORQUE DISTRIBUTION ALL-WHEEL DRIVE: As with Active All-Wheel Drive, an electronically controlled variable transfer clutch distributes power, but through a planetary-type center differential and a viscous-type limited-slip rear differential. Torque distribution is normally configured at a performance-oriented rear-wheel-biased 45/55 split front to rear. Sensors monitor the same parameters as for Active All-Wheel Drive.

WRX STI, WITH SIX-SPEED MANUAL TRANSMISSION – DRIVER CONTROLLED CENTER DIFFERENTIAL (DCCD) ALL-WHEEL DRIVE: The STI uses an electronically managed multi-plate transfer clutch and a mechanical limited-slip differential in conjunction with a planetary-gear-type center differential to control power distribution between the front and rear wheels. Featuring manual and three automatic modes, DCCD is normally configured at a 41/59 split front to rear. Sensors monitor parameters such as wheel slippage, steering angle, throttle position, and braking to help determine torque distribution and direct it to the wheels with optimum traction. DCCD also features a limited-slip helical front and Torsen® rear differential. ... }

And what are the symptoms? How do you know the coupling to the rear is not working?

try adjusting your herz default is 60hz most of the time

Have you tried a old display again and worked?
mabe just bad Monitor try on dif computer see if you have the same results.
another thing would to be update the driver for the video card mabe compat. issue with older card newr monitor

Anti-Lock Control —Vehicles Built After 03/2002 The 3-channel anti-lock brake system consists of the following components:

• front wheel speed sensors
• front wheel speed sensor rings
• hydraulic control unit (HCU)
• Anti-lock brake control module (ECU)
• rear wheel speed sensor
• rear wheel speed sensor rings
• yellow anti-lock brake warning indicator

The 4-channel anti-lock brake system with traction control and stability assist system consists of the following components:

• active brake booster with integral solenoid
• brake booster release switch
• front wheel speed sensors
• front wheel speed sensor rings
• hydraulic control unit (HCU)
• stability assist module (ECU)
• stability assist event indicator
• lateral accelerometer
• longitudinal accelerometer (4x4)
• rear wheel speed sensors
• rear wheel speed sensor rings
• steering wheel position sensor
• yaw rate sensor
• yellow anti-lock brake warning indicator
• brake pressure transducer
• traction control switch

---------------------------------------------------------------------
I suspect the abs issue is causing the speed control not to work if it happened at the same time the cruise control stopped working. When the yellow ABS light comes on, it means the ABS is dactivated. You may have a faulty accelerometer which senses acceleration and yaw (side to side lean). I have not seen a bad one but you said it is sensitive to acceleration.
I would unplug it and see what happens. The connector should have a small tab to depress so you can pull the connector out.
Here is where it is:

Accelerometer Removal and Installation

1. NOTE: The accelerometer is located under the center, rear passenger seat carpet. (I think you have to remove seat for access).
   Cut the carpeting along the perforations.

1. Disconnect the electrical connector.

1. Remove the nuts and remove the accelerometer.

Have dealer hook up tester and pull fault codes if you can't find an easy solution.
Some background info

A malfunction in the anti-lock brake system will cause the anti-lock brake control module to shut off or inhibit the system. However, normal power-assisted braking remains.

Malfunctions are indicated by the yellow ABS warning indicator in the instrument cluster.

The anti-lock brake system is self-monitoring. When the ignition switch is turned to the RUN position, the anti-lock brake control module will carry out a preliminary self-check on the anti-lock electrical system indicated by a three-second illumination of the yellow ABS warning indicator in the instrument cluster.

During vehicle operation, including normal and anti-lock braking, the anti-lock brake control module monitors all electrical anti-lock functions and some hydraulic operations.

Each time the vehicle is driven, as soon as vehicle speed reaches approximately 20 km/h (12mph), the anti-lock brake control module turns on the pump motor for approximately one-half second. At this time, a mechanical noise may be heard. This is a normal function of the self-check by the anti-lock brake control module.

Pedal pulsation coupled with noise while braking on loose gravel, bumps, wet or snowy roads is normal and indicates correct functioning of the anti-lock brake system.

Warning Lamp Indicator
The anti-lock brake system (ABS) uses the yellow ABS warning indicator to alert the driver of a malfunctions in the ABS.
The yellow ABS warning indicator will come on to warn the driver that the ABS has been turned off due to a symptom that exists in the ABS. Normal power assist braking remains but wheels can lock during a panic stop while the yellow ABS warning indicator is illuminated.

-----------------------------------------
Please report back, I am curious if that is what it is. Good luck