2007 Lexus is250 cam positioning sensor bank 2 wiring diagram

Question edited for clarity, spelling of maker, and toss in CAPS.
Question translated to English.
Question moved to model category.

We are a North American website, we only converse in English.

https://www.google.com/search?q=solenoid+B+located+on+a+2007+Lexus+IS250

https://translate.google.ca/

..

Lexus IS250 repair manuals are available at the click of a mouse! Chilton's Lexus IS250 online manuals provide information for your car's diagnostics, do-it-yourself repairs, and general maintenance.
Chilton's Lexus IS250 repair manuals include diagrams, photos, and instructions you need to assist you in do-it-yourself IS250 repairs. ChiltonDIY online IS250 repair manuals cover automotive service and repairs, from diagnostic trouble codes and probable causes, electronic engine controls, and maintenance schedules, to brake and suspension issues, wiring diagrams and engine repairs, tune-up procedures, specifications, clutch and gearbox diagrams, and more.

(1) Camshaft Position (CMP) Actuator Solenoid - Intake Bank 1
(2) Camshaft Position (CMP) Sensor - Intake Bank 1
(3) Camshaft Position (CMP) Sensor - Intake Bank 2
(4) Camshaft Position (CMP) Actuator Solenoid - Intake Bank 2
(5) Camshaft Position (CMP) Actuator Solenoid - Exhaust Bank 2
(6) Camshaft Position (CMP) Sensor - Exhaust Bank 2
(7) Generator
(8) A/C Compressor Clutch
(9) Camshaft Position (CMP) Actuator Solenoid - Exhaust Bank 1
(10) Camshaft Position (CMP) Sensor - Exhaust Bank 1

One crank sensor. It needs to go on a scanner. Both sensors are probably OK. Your problem is most likely the timing chains or guides. If ti were the crank sensor, it wouldn't start. Cam sensor would throw a cam code. Correlation means the crank and cam are not in sync. If you have VVT, it could be the actuator.

Well the code means there is a problem with the cam sensor position for bank 2. The sensor is telling the engine computer the cam is in a different position that it should be.
You would need to check the signal from the sensor, and the actual cam to find the problem.

If your connector has only two wires... A. It may not matter. B. Look at the connector for a different color clip inserted into it. Removing the clip should allow the piece that holds the wires to release, and maybe there is enough wire there for you to see which goes where.

Just remember how it goes together.

A dealer can tell you or simply see if they have a similar model on the lot, and ask to look under the hood.

Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

My 2007 Lexus IS250 is dead, hooked up a charger. Charger keeps shutting off. Triple checked the cables, + - correct, still shuts off charger?