SOHC V6 Torque Specifications - Ford Explorer and Ranger Forums ...
https://www.explorerforum.com/forums/showthread.php?t=406687
Apr 25, 2014 - SOHC V6 Torque Specifications Under the Hood. ... related to the Ford SOHC V6 4.0L engine used in Explorers, Mountaineers, Mustangs and Rangers. .... Oilpan (sheet metal) to crankcase reinforcement section bolts: 80 lb-in (E/MWM) ....Ranger Mountaineer - Sport thru '03 - 2nd Generation, 2002 - 2005 ...
Transmission pan drop
5 posts
May 7, 2012
SOHC V6 Timing Chain Inspection & Repair
19 posts
Aug 10, 2010
Another transmission won't go after fluid change
19 posts
Mar 14, 2009
Help with 4.0 SOHC timing
15 posts
Mar 12, 2006
More results from www.explorerforum.com
[PDF]SPECIFICATIONS > TORQUE SPECIFICATIONS
www.askatech.com/askatechlive/forums/resourcehandler.ashx?a=5581
Jan 6, 2014 - TORQUE SPECIFICATIONS ... ENGINE - 4.0L SOHC. 2002 FordExplorer Sport Trac 4.0L Eng. (1). (2) ... Oil Pan Ladder Frame Bolts (Inside).
Torque Specifications - AutoZone
SOURCE: Need torque specs for oil pan gasket
There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.
SOURCE: torque specs 7.5 inch rear axle 96 ford ranger
Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in
SOURCE: 87 samurai bolt torque specs for engine
The haynes book is not recommended since there are numerous mistakes and they still will not update. One of the biggest is the firing order.
The factory service manual is the only way to go.
Head bolts - 46 - 50.5 lbs (there is an order sequence for the bolts)
Intake & exhuast manifolds- 13.5 - 20 lbs
Flywheel - 41.5 - 47 lbs
Clutch cover - 13.5 - 20 lbs
SOURCE: head bolt torque specs for 2000 dodge neon 2.0 SOHC
I have the specs and diagrams. If you want me to send them to you, give me your email address. [email protected]
SOURCE: need cylinder head gasket torque specs.
looks like there is special sequence to reassemble and tightening, a quick note replace any bolts that have two punch marks.tighten as follows: x x x x x 10 4 2 6 8 x x x x x 7 5 1 3 9 torque all down to 15 ft lbs torque to 30 ft lbs plus 90 degrees. Good luck!
1,796 views
Usually answered in minutes!
×