Question about Honda Accord

1 Answer

1999. Where can I get a replacement ECM? - Accord Honda Cars & Trucks

Posted by James Thornhill on

Ad

1 Answer

paulmacintyre

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 3,218 Answers

Why change the ECM? These rarely fail on Honda. If it is defective, you can usually pick one up at any salvage yard

Posted on Dec 19, 2015

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1999 grandprix code po502


Check harness / wiring for continuity , damage , chaffing, connector contact, etc... from speed sensor to ECM.

Dec 28, 2013 | 1999 Pontiac Grand Prix

1 Answer

Bad ecm 1999 accord lx 3.0v6


doubt it.. dealer item..

Dec 20, 2013 | 1999 Honda Accord

1 Answer

WON'T START AFTER REPLACING THE ECM. IS THERE A WAY I COULD GET THE TANSPONDER TO WORK WITH THE NEW ECM?


you cant just replace an ECM you must replace the throttle body. find one online on ebay.

Dec 18, 2013 | 1999 Honda Accord

1 Answer

1999 vw beetle wont take gas tried throttle poshining sensor need help no money no more ideas


IF YOU REPLACED TPS SENSOR CAR WONT ACCELERATE THE FUEL FILTER COULD BE STOPPED UP.OR THE ECM FAULTY. ECM CONTROLS FUEL THROUGH THE TPS SENSOR.HAVE ECM CHECKED.

Sep 24, 2011 | 1999 Volkswagen Beetle

2 Answers

Why dose my 1999 chevy1500 my ecm/b fuse burns out while driving


This is caused by the in tank electric fuel pump drawing to excessive current, you will need to replace the fuel pump and replace the fuel pump connector at the fuel tank. Both parts are in the aftermarket. Please note the fuel tank connector MUST be replaced as it is really the root cuase of htis problem.

May 11, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

Car turns over but will not start. is there anyway to check to see if it is the car computer


Yes you ll need a scan tool for a 1999 youll have ti inspect the RPM signal,If the ECM reads greater than 250 RPM and you car will not start the ICM will need to be replaced. If your ECM during cranking reads less than 250 RPM and a Cranksensor was replaced and the ICM is a known good one the last is the ECM only a labscope can do all this test without replaceing parts

May 01, 2011 | 1999 Buick LeSabre

1 Answer

99 elantra alt not charging battery' installed new alt and battery and fuse good and still no charge on battery


check 10 amp ECM fuse. Your alternator voltage is regulated by the ECM. If the fuse is good, consider replacing the ECM.

b4f4aeb.gif

Oct 05, 2010 | Hyundai Motor 1999 Elantra

2 Answers

Lexus rx300 2002 hard shift between 1st and 2nd. Fluid and filter changed 3000mi ago, car has 93000mi


The 1999-2003 Lexus RX300 models have a common failure of the engine computer that causes the harsh shifting of the transmission. You need to get the computer (ECM - Engine Control Module) rebuilt or replaced before it causes permanent damage to the transmission. Even if the transmission is already ruined, the ECM will still need to be repaired. Most often, the transmission is fine though, and rebuilding the ECM will restore the smooth shifts that the Lexus should have. Circuit Board Medics can rebuild the ECM and reprogram it so that you only have to plug it back in when you get it back. See the link below:

http://circuitboardmedics.com/1999-2003-lexus-rx300-hard-transmission-shifting-ecm-ecu-computer-repair/

Jan 25, 2010 | 2002 Lexus RX 300

1 Answer

Hi, the "check engine light" on my 1999 silverado is on but when i plug the codes can't be read from the device that plugs into the module, the fuses are not burnt out so it appears to be a problem with...


dont expect the ecm to be the problem. a good scanner will access the codes. Let me know the codes after you have them read. Autozone offers free scan service. Dont trust there diagnostic skills just get the codes and leave. Before replaceing ecm wireing should be checked

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/thomas_c50676e836a18949

Jan 13, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

1999 Dodge ram Volage Problem


the voltage is controled by the ecm you will need a scanner to be able to read the date stream . the odds are that ecm has failed.

Jan 01, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...