CAN HONDA ACCORD 2.3L TRANSMISSION BOLT TO HONDA ACCORD 3.0L

1994-1997 Honda Accord Rear Motor Mount - YouTube

? 13:31
https://www.youtube.com/watch?v=QTDLBZonjvo
Aug 14, 2014 - Uploaded by NutzAboutBolts
1996 Honda Accord rear engine mount Tools: Impact wrench 3/8 ratchet ... Wat size are those bolts in the rear motor mount, I have to replace them ..... 1998-2002 Honda Accord 3.0 V6 Spark Plug Replacement - Duration: ...

How to Replace the Motor Mount on a Honda Accord ...

? 5:28
https://www.youtube.com/watch?v=jCIBNq0jg0U
Oct 17, 2013 - Uploaded by Chandler Cox
How to Replace the Motor Mount on a Honda Accord .... I have 2001 Accord and engine/front vibrates when car is idle. .... onreplacing and removing rear mounts for this year and model car.... 1998-2002 Honda Accord 3.0 V6 Spark Plug Replacement - Duration: 12:48. by CharlietoKind 103,467 views.

How To Change A Motor Mount and Transmission Mount ...

? 29:43
https://www.youtube.com/watch?v=vkO19Ux9q9M
May 30, 2013 - Uploaded by klowny1969
Step by step honda transmission motor mount and transmission... 2000 2001 2002 2003 2004 2005 engine mount how to replace install check change ... MAKE A VIDEO TO INSTALL THEREAR MOUNT MOTOR PLEASE .

The speed sensor located near the drive shaft from the gearbox with a 3 wire n a 10mm bolt.. Try look somewhere where the drive shaft come out from ur gearbox

My 1995 Honda Accord EX Transmission was completely sometimes could not drive smoothly and sometimes too slow. Seems like not ingear in motion. A lot of drivers in the free-way hornned me. I got stress out. So tell me to change the new transmission or not!

There should a "big bolt" on the side of the transmission. Take bolt out and see if you can put your finger in the hole and bend your finger .....if you get oil on your finger it has enough oil in it ( or if you take the bolt out and oil comes out, its got enough oil in it.) Make sure to use honda oil....... it should be 90 weight.

the starters are attach to the transmission with two bolts. honda accord starter is located on the transmission behind the bottom radiator hose that goes to the back of the engine.

If it's automatic, drain the trans fluid and clean the magnetic drain bolt. Remove and clean the screens on the two solenoids on the front of the transmission. Honda does NOT recommend flushing your transmission with any solvents. Refill to the correct level according to your owner's manual.

If it's a manual transmission, change your gear oil in the transmission according to your owner's manual and hope it's not your synchros.

first clean off the tranny with a jetwash or similar give it a run to help determine the exact area it could be running down from above. ie. speedo transducer if its at the 2 housings join together then the only proper way is to strip it down and reseal the 2 castings using the correct sealant/gasket from memory the casings distort with heat from the torque convertor and gives your problem .good luck

if youre gonna heat anything heat the bolt then cool it quickly, it will expand in the aluminium then shrink when cooled, used to do that with vw exhaust studs

not sure how rought but traditionally, Honda's are known to shift rough... its kinda their sporty style. I think its funny that the Accord is considered a "sedan", when clearly is not a Taurus or Impala which are purely sedans.

cheers!

Owner of 1997 Honda Accord SE

remove the egr .clean the carbon out the intake where egr valve sits . use a small tiny tiny screw driver or old coat hanger clean out the hole then vacuum up carbon.put back egr valve.