At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Power windows, interior lights, mirrors, door locks won't work. Already took door panel apart, couldn't find anything wrong there. Is there a fuse somewhere that controls this stuff?
run a jumper wire from the door lock on the driver side to the bolt for the mirror and it will fix your problemrun a jumper wire from the door lock on the driver side to the bolt for the mirror and it will fix your problem
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
F5
5
Rear window motor. Roof opening panel module. Auto-dimming interior mirror unit. Door lock switch, driver side. Door lock switch passenger side. Power window motor, driver side front. Overhead console switch assembly
Not sure if this is what you're looking for. Let me know if it works.
your master control module is bad..we just did this with a close friends' jeep.. it went all funky and I couldnt figure it out at first..the dealer we took it to fixed it because it was and still is under warranty.. thats what was wrong with hers..
Since it is only happening on the drivers side door to multiple switches and lights on that door only, I think the problem is the wiring harness as it enters the drivers door by the door hinges.
I had same problem it is a ground wire broken in the harness rubber boot between dthe driver door. Peel back the rubber that protects wires and you will find broken ground wire(black) add a piece of wire solder and wrap with electrical tape put rubber boot back into door everything should work.
slide the rubber boot up and check the wires in the hinge of the doors. I will bet anything that the wires are broken. that was what was wrong with mine. just splice them back together and everything should work fine.
Exterior Mirror
Removal and Installation All vehicles
NOTE: Left side exterior mirror shown, right side similar. Remove the interior door trim panel. For additional information, refer to Section 501-05 .
Front Door Trim Panel
Removal and Installation
Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
Remove the inside door handle bezel from the trim panel.
Remove the window switch assembly.
Disconnect the window switch and power door lock electrical connectors.
Remove the upper trim panel screw at the window switch opening.
Remove the lower trim panel screws.
CAUTION: To avoid damage to the door trim panel, do not pull directly outward for this step. Lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
Disconnect the power mirror electrical connector.
Remove the trim panel.
Remove the weather shield.
Vehicles with power, heated or approach lamp equipped exterior mirrors
Both above answers are not right... I just replaced the Pass side power mirror assembly on my 97 Expedition. No heat, no directional. The inside door panel must come off. 1. pry off interior triangular plastic trim piece inside of door at mirror area. Remove door panel screw at this area. 2. Pry off power window switch panel and remove door panel screw at this area. 3.Remove interior door light cover and remove screw at this area. 4. Remove plastic cover at door handle. 5. The interior door panel can now be lifted up to release it from it's fasteners. 6. Disconnect light and push power window switch assembly through the door panel and it can be set aside. 7. Disconnect mirror power at coupler. 8 Loosen three mirror mounting screws with 7/16 socket. DO NOT unscrew completely.. the will fall down the door cavity. Use a round magnet on holder to remove the screws completely. 9.Thread electrical connection into door panel and install mirror. 10. Smile when mirror works and drink a beer! rayman
Hi all,
suppose you have worked out your little problem. I have just been experiencing the same thing with my 2004 GC ltd. Windows, mirrors, etc not working and interior light staying on. Took it to the shop and they re soldered the wire (behind the door panel) that had come off. Cheap problem really.
run a jumper wire from the door lock on the driver side to the bolt for the mirror and it will fix your problem
×