Big end torque settings for jeep 2.4l cp engine

https://www.google.com/search?q=2012+chevrolet+captiva+2.2+VCDi+diesel+cylinder+head+torque+specs

https://www.google.com/search?q=2012+chevrolet+captiva+2.2+VCDi+diesel+big+end+torque+specs

Not too much information on the 2.2 diesel. A service manual is the best idea.

..

I'm sorry, but I'm not able to find the specific torque settings for the crankshaft main and big end bolts for the E2200 R2 engine without more information, such as the year of the engine or the vehicle it's installed in. The torque settings can vary depending on the specific engine and vehicle model.
I would recommend referring to the engine's service manual or contacting a certified mechanic for the specific torque settings for your engine to ensure proper installation and prevent damage.

In the link

https://www.google.com/search?q=Jetta+iv+1.6+AKL+engine%2C+main+and+big+end+torque+settings

..

Here are the torque settings for a Ford Fiesta 1.4 2010 for the main bearings, head bolts, and big ends:
Main bearings

• Main bearing caps: 1st stage - 7 Nm, 2nd stage - 16 Nm
• Main bearing bolts: 45 Nm + 90°

Head bolts

• Cylinders 1-3: 2nd stage - 30 Nm + 90°, 3rd stage - 80 Nm + 180°
• Cylinder 4: 2nd stage - 25 Nm + 90°, 3rd stage - 60 Nm + 180°

Big ends

• Connecting rod cap nuts: 1st stage - 22 Nm, 2nd stage - 40 Nm + 90°

Please note that these are just the general torque settings. The exact torque settings may vary depending on the specific engine and vehicle. It is always best to consult your vehicle's service manual for the correct torque settings.
Here are some additional tips for tightening the torque settings:

• Use a torque wrench to ensure that the bolts are tightened to the correct torque.
• Tighten the bolts in a star pattern, working your way from the center out.
• Do not overtighten the bolts, as this can damage the engine.

https://www.hyundaiaftermarket.org/forum/engine-intake-exhaust-11/hundai-i10-big-end-main-bearing-torque-specs-80245 https://www.hyundaiaftermarket.org/forum/engine-intake-exhaust-11/hundai-i10-big-end-main-bearing-torque-specs-80245

It always helps to include the engine code... The following torque settings are used on the folowing engine codes:
ATN, AUS, AZD, BCB
This is for the Golf 4 1.6 16 valve engines
Mains:
32 Nm
65 Nm

Big Ends
30 Nm
90 Degree turn.

Download this manual. It should have all the torques you are asking for.

http://www.championbrands.com/aera-torquespecs.pdf

Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

V6 colt bakkie big ends bearing torque settings

Mains Stage 1 83nm
Mains Stage 2 167nm

Big ends Stage 1 29nm
Big ends Stage 2 45 - 60 degrees

Hope this helps