Question about 2005 Chevrolet Impala
The sensor may be good its the circuit code which means can be a wiring /connection problem not just the sensor the following link is courtesy of obd-codes.comP0335 - Crankshaft Position Sensor A Circuit Malfunction OBD-II Trouble Code Technical Description Crankshaft Position Sensor A Circuit Malfunction What does that mean? The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 will set. Symptoms NOTE: If the crank sensor is used only for misfire detection and NOT spark timing (this varies with the vehicle), the vehicle should start and run with MIL (Malfunction indicator lamp) illumination. Also, some vehicles require several key cycles to illuminate the MIL. If this is the case, there may be no MIL illumination until the problem often enough over time. If the crank sensor is used for BOTH misfire detection and spark timing, the vehicle may or may not start. Symptoms may include: Vehicle may not start (see above) Vehicle may run rough or misfire MIL illumination Causes A P0335 "check engine light" code could be caused by: Damaged CKP sensor connector Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway) Sensor output open Sensor output shorted to ground Sensor output shorted to voltage Failed crank sensor Broken timing belt Failed PCM Possible Solutions Using a scan tool, check if, when engine is running or cranking, that there is an RPM signal. If there is no RPM reading, then visually inspect the crank sensor and connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there's no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the sensor and measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn't be performed if you\'re not familiar with automobile electrical systems). Is the sensor within resistance specs? If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay? If not, repair open or short in the wiring to the crank sensor and re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault. This code is basically identical to P0385. This code P0335 refers to Crankshaft Posistion Sensor "A", whereas P0385 refers to Crankshaft Position Sensor "B". Other crank sensor codes include P0016, P0017, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.
Read more at: http://www.obd-codes.com/p0335
Posted on Aug 19, 2015
Tips for a great answer:
May 17, 2018 | Cars & Trucks
Dec 13, 2015 | 2006 Nissan Sentra
Mar 19, 2012 | Cars & Trucks
Nov 18, 2011 | Cars & Trucks
Apr 20, 2009 | 2000 Chrysler Cirrus
Dec 31, 2008 | 2004 Renault 181
464 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: