2006 Kia Rio LX with a 1.6L DOHC 16 valve engine.

Question edited for clarity.

Question moved to model category.



https://www.google.com/search?q=2009+kia+rondo+lx+2.4+set+valve+timing+marks



..

2006 - 2011 Kia Rio timing belt replacement.

https://www.youtube.com/results?search_query=timing+on+a+2006+kia+rio+1.6+engine+

Hope this helps.
Geoff

replaced crank and cam sensor [Archive] - Sorento Nation - KIA ...

www.sorentonation.com/forum/archive/index.php/t-913.html

20 posts - ‎6 authors
replaced crank and cam sensors put back together cranked up very rough idle some tapping any ... 12-17-2012, 12:24 AM ... It's a 2006 3.5 Kia Sorrento. ... I found theproblem the SUV has a aftermarket alarm and remote start system I tripped ...

Kia Rio Crankshaft Position Sensor Replacement - YouTube

? 4:44
https://www.youtube.com/watch?v=hihQxMWuSFY
Mar 21, 2014 - Uploaded by Jason Roush
While looking for how to replace a Kia Rio crankshaft positionsensor, ... is on and i have a P0340 code, think this is theproblem? kia rio 2002.

Kia Sorrento/Sedona: 3.5 Litre Engine/Timing Belt/Crank ...

? 20:23
https://www.youtube.com/watch?v=CjaD_zYPrUA
Mar 29, 2014 - Uploaded by JamieJones TheCarMan
Repair and/or Replacement tips for timing belt, crank sensor,cam sensor, water pump and drivebelt ...

Crankshaft position sensor - 2003 Kia Sorento - RepairPal

repairpal.com > Questions > Kia > Sorento > 2003 Kia Sorento

Water pump is Timing belt driven. It is below the Camshaft sprocket, in the timing case. If you want to repair/replace it here are the instructions.
>

COMPONENTS

REMOVAL

1. Using the drain plug, drain the coolant.
2. Remove the drive belt and the engine coolant pump pulley.
3. Remove the timing belt cover, the auto tensioner and idler pulley.
4. Remove the water outlet fitting, the thermostat case and the water pump fitting.
5. Remove the engine coolant pump mounting bolts.

1. Remove the engine coolant pump assembly from the cylinder block.

INSPECTION

1. Check the engine coolant Water pump for cracks, damage or wear, and replace the pump assembly if necessary.
2. Check the bearing for damage, abnormal noise and sluggish rotation and replace the pump assembly if necessary.
3. Check the seal it for leaks and replace the pump assembly if necessary.

INSTALLATION
>

1. Clean the gasket surfaces of the engine coolant pump body and the cylinder block.

>

1. Install the new engine coolant pump gasket and pump assembly. Tighten the bolts to the specified torque. Tightening torque

Engine coolant pump bolt:
Head mark "7": 17 - 22 Nm(170 - 220 kg.cm, 12 - 16 ft. lbs.)

1. Install the water pump fitting, the thermostat case and the water outlet fitting.
2. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
3. Install the drive belt, coolant pump pulley and then adjust the auto tensioner.
4. Refill the coolant.
5. Run the engine and check for leaks.

Courtesy All Data LLC
© 2015 ALLDATA LLC. All rights reserved. Terms and Condit

Hi:
Yes, this engine isn an interference engine, and your valves will get ruined if your timing belt breaks. It is money well spent to replace it , and don't forget to have the water pump and tensioner replaced at the same time!

take it in its alot of pissing around about the timing belt i wouldent recomend to do it yourself

I would follow the mechanics recommedations. I think he's taliking about the cam and crankshaft seals. Yes the water pump should be replaced as well. The pump that sprays windshield washer fluid onto the windshield is called the windshield washer pump. The water pump is on the engine and pumps water (coolant/antifreeze) through the engine to the radiator and heater core.

The thing is your doing the timing belt the water pump is right their with it . it should cost you much more at all besides the cost of the water pump. When doing a timing belt I have a rule that I go by The timing belt/seals =cam , crank , any pulley & tensioner & water pump all get replaced at the same time. I did a t-belt on a Audi A-8 very complex whole front of car has to come off as well, he didnt want to do w-pump & thermostat his thermostat was their as well not even a month later the water pump gave out he had to pay double the price because he didnt want to do it when I had it apart the first time. And make sure mechanic is ase certified . good luck

Do a compression check. You might have bent the valves.