Question about 2004 Chevrolet Venture Passanger

Open Question

Can you use a used pass key 3 on a chevy venture

Can you use a used pass key 3 from another van

Posted by carole on

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: Thermostat in a 2003 chevy venture van

the bottom boult is hard but can be done need to use a 10 or 12 stubby wrench and take a pry bar and lighty pry heat shild away to get bottom bolt dont need to take it out all the way just loosen and slide down

Posted on Aug 17, 2008

Ad

Anonymous

  • 22 Answers

SOURCE: blower fan

it sounds to me like your blower moter resister or your blower moter switch are going bad both are right under the hood next to the blower moter one has 2 witers on it the other has 4 it usuley on the pass side right near the window

Posted on Dec 03, 2008

Ad

Rick Gillis

  • 37 Answers

SOURCE: rear brakes scrubbing on 1998 chevy venture van

Removal Procedure Tools RequiredJ 38400
Caution: Keep fingers away from rear brake shoe springs to prevent fingers from being pinched between spring and shoe web or spring and backing plate.

  1. Remove the brake drum. Refer to Brake Drum Replacement

  2. 142285.gif
    tif.gif
    Notice: Do not over stretch the adjuster spring. Damage can occur if the spring is over stretched.
  3. Use the J 38400 in order remove the adjuster spring (1). Disengage the adjuster spring loop from the tab on the adjuster actuator.
  4. 2.1. Remove the loop end of the adjuster spring from the adjuster actuator. 2.2. Remove the straight end of the adjuster spring from the secondary brake shoe.
    142293.gif
    tif.gif
  5. Use the J 38400 in order to spread the brake shoes apart.
  6. Remove the adjuster.
Installation Procedure

    142293.gif
    tif.gif
  1. Use the J 38400 in order to spread the brake shoes apart.

  2. 178990.gif
    tif.gif
    Important: Ensure that the adjuster (2) engages the brake shoes (4 and 5), the park brake actuator (3), and the adjuster actuator (1) properly.
  3. Install the adjuster.

  4. 142285.gif
    tif.gif
    Notice: Do not over stretch the adjuster spring. Damage can occur if the spring is over stretched.
  5. Install the adjuster spring (1).
  6. 3.1. Install the straight end of the adjuster spring into the secondary brake shoe. 3.2. Install the loop end of the adjuster spring to the adjuster actuator.
  7. Install the brake drum.

Posted on Dec 08, 2008

Anonymous

  • 1 Answer

SOURCE: Thermostat in a 2003 chevy venture van

no you dont need a special tool you have to take the throttle body off it makes it sooooooo much more simple.

Posted on Jan 27, 2009

Anonymous

  • 150 Answers

SOURCE: Radio, Key auto door lock/opener, interior lights not working.

Most likely is a fuse. There is a fuse box at the end of the right side of the dash. Open front passenger door and there is a cover that says fuses on the end of dash. There is also a fuse box located under the hood at the right front of engine compartment. It should have a cover with a round knob in the middle of it .Unscrew the knob to remove cover.

Posted on Feb 18, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 chevy venture won't crank with key


The pk3 system has a sensor ring around the lock cylinder these go bad a relearn will not fix this because no security code is being sent to the pass key module.

Mar 23, 2014 | 2000 Chevrolet Venture

1 Answer

The chevy venture i replaced the pass key in has the PK3 key and i cant get it to start


The module may have failed.
The module reads the chip in the key thru the sensor in the lock cylinder.

Sep 24, 2012 | 1999 Chevrolet Venture

1 Answer

2001 chevy venture van and i cannot turn the key


While turning the key rotate the steering wheel left and right. If there is too much tension on the parking lock the key cannot be turned.

Feb 07, 2010 | 2001 Chevrolet Venture

3 Answers

2000 chevy venture doesnt start


check to make sure the security light is not on if it is the van will have spark but no injecter pulse the best way to solve this issue is to have the original igniton key and put it in the igniton in the run position and leave it on for 10 minutes then the light will flash then try to start the van

Jul 15, 2009 | 2001 Chevrolet Venture

1 Answer

Replaced battery securty light came on power no start


Here is something that the emission wiz helped me with


PASS LOCK RESET GM CARS 1999 UP
1) Put the key in the ignition and turn to the "ON" position. Leave it that way for 10 minutes. After 10 minutes turn the key and take it out. Repeat this process (2) more times (3 times, 30 minutes total) This should reset the passlock system to recognize your key
.

Mar 14, 2009 | 1997 Chevrolet Venture

1 Answer

Need wiring dig. for 2005 chevy venture window switch


call any gm parts dept they can print one up for you just give them your vin Please rate my response thank you very much

Feb 02, 2009 | 2001 Chevrolet Venture

1 Answer

Program master key for 2000 chevy venture


To program a new key...
1-Turn ON the ignition, with the engine OFF, using a master Pass-Key III key (black).

2-Observe the security telltale. After approximately 10 minutes the telltale will turn off.

3-Turn OFF the ignition, and wait 5 seconds.

4-Repeat step 1-3 two more times, for a total of 3 cycles or 30 minutes.
Tech JK
-----------------------------------------------

Jan 01, 2009 | 2000 Chevrolet Venture

1 Answer

Blower fan


it sounds to me like your blower moter resister or your blower moter switch are going bad both are right under the hood next to the blower moter one has 2 witers on it the other has 4 it usuley on the pass side right near the window

Dec 03, 2008 | 2000 Chevrolet Venture

2 Answers

Thermostat in a 2003 chevy venture van


no you dont need a special tool you have to take the throttle body off it makes it sooooooo much more simple.

Nov 27, 2008 | 2004 Chevrolet Venture Passanger

2 Answers

Thermostat in a 2003 chevy venture van


the bottom boult is hard but can be done need to use a 10 or 12 stubby wrench and take a pry bar and lighty pry heat shild away to get bottom bolt dont need to take it out all the way just loosen and slide down

Aug 08, 2008 | 2003 Chevrolet Venture Passanger

Not finding what you are looking for?
2004 Chevrolet Venture Passanger Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...