Question about 1998 Ford Explorer

1 Answer

What is the torque specs for brake calipers on a ford explorer sport front calipers

Front brake calipers mount bolts and banjo bolt what should they be torque to.

Posted by j thotpe on

Ad

1 Answer

Claude Kayser

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 9,098 Answers

  1. Torque Specs For F250 Caliper Bolts - Diesel Forum - TheDieselStop.com

    www.thedieselstop.com > ... > 1999-2007 General Questions Jan 13, 2009 - 3 posts - ‎1 author
    Does any one know what the caliper bolts torque specs are? ... Disc brake caliper pin bolts - Excursion, F-250/F-350 with Ford and Dana axle ... Torque specs for front brakes
    5 posts
    Mar 12, 2009
    05 F250 brake torque specs please
    6 posts
    Aug 22, 2007
    Brake caliper torque specs
    5 posts
    Jul 14, 2007
    Front brake Caliper Bolt Torque
    6 posts
    Apr 25, 2005
    More results from www.thedieselstop.com

Posted on Jul 11, 2015

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Caliper bolts get loose


the main mounting bolts? not guides?
caliper mount to knuckle bolts?
what torque did you use? in foot/lbs.

  1. id bet they are not factory spec bolts
  2. or you used the wrong torque page.
  3. or your tool is no good. (harbor fright tools?)
use a beam torque tool, it will never fib to you, like cheap clickers do.
I promise.
specs
tighten the caliper pin bolts to 26 ft. lbs. (36 Nm). Bottom bolt
there are 4 bolts specs here.
above pin
banjo 17ft/lbs
top B bolts is 61.5 foot lbs. (this came loose at 61 ?)
C spec is 5ft/lbs on bleeder nipples.

now alternator tack.
the rotor is warped so bad it bead the calipers to death.
the wheel bearing, is so bad , same.

ever check those for run out, and end play?
bingo if true.
damage and collateral damage are limitless.
and rust too. (entropy of all kinds)

Apr 16, 2014 | 2010 Suzuki Grand Vitara

1 Answer

Front caliper bolts torque


  1. Remove or disconnect the following:

    Wheel Brake hose from the caliper Caliper mounting bolts Caliper
To install:

  1. Install or connect the following:

    CaliperCaliper mounting bolts and tighten to 58-73 ft. lbs. (80-100 Nm) on the front caliper, or 37-44 ft. lbs. 50-60 Nm) on the rear caliper.Brake hose to the caliper and tighten the fitting too 18-22 ft. lbs. (25-30 Nm)Wheel
  2. Bleed the brake system.

Sep 23, 2013 | 2004 Hyundai Santa Fe

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

2001 honda passport front brake rotors do not just come off after the caliper is removed. It is bolted to the hub. Trust me, it is different than most other cars. You do not just pull the cotter pin &...


IF this helps, don't forget to vote.

Removal & Installation


CAUTION Dust and dirt accumulating on brake parts during normal use may contain asbestos fibers from production or aftermarket brake linings. Breathing excessive concentrations of asbestos fibers can cause serious bodily harm. Exercise care when servicing brake parts. Do not sand or grind brake lining unless equipment used is designed to contain the dust residue. Do not clean brake parts with compressed air or by dry brushing. Cleaning should be done by dampening the brake components with a fine mist of water, then wiping the brake components clean with a dampened cloth. Dispose of cloth and all residue containing asbestos fibers in an impermeable container with the appropriate label. Follow practices prescribed by the Occupational Safety and Health Administration (OSHA) and the Environmental Protection Agency (EPA) for the handling, processing, and disposing of dust or debris that may contain asbestos fibers.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and safely support the vehicle. Remove the front wheels.
  3. Remove some brake fluid from the master cylinder reservoir.
  4. Disconnect and plug the brake fluid line from the caliper.
  5. Remove the brake caliper mounting bolt and guide bolt and remove the caliper from the mount. The brackets can be removed for additional work space.
  6. Remove the brake pads and clips from the caliper. Inspect the brake pads for wear; replace them, if necessary.

    0996b43f802018f3.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Front caliper and related parts


To install:
  1. Install the brake pads and clips onto the caliper.
  2. If the caliper bracket was removed, tighten the bolts to 115 ft. lbs. (155 Nm).
  3. Install the caliper on the mounting bracket. Torque the caliper-to-mounting bracket bolts to 33 ft. lbs. (45 Nm).
  4. Connect the fluid line to the caliper using new washers. Torque the brake line banjo fitting to 26 ft. lbs. (35 Nm).
    WARNING Be sure the hook end of the flexible brake line is positioned in the anti-rotation cavity.
  5. Refill the master cylinder reservoir and bleed the brake system.
  6. Install the front wheels and lower the vehicle.

icn_arrow.gifBack to Top

Jan 15, 2011 | 2001 Honda Passport

1 Answer

How do I replace the ear brakes?


Bonneville, LeSabre, Park Avenue 2000-2005

Brake Caliper - Removal & Installation

CAUTION Dust and dirt accumulating on brake parts during normal use may contain asbestos fibers from production or aftermarket brake linings. Breathing excessive concentrations of asbestos fibers can cause serious bodily harm. Exercise care when servicing brake parts. Do not sand or grind brake lining unless equipment used is designed to contain the dust residue. Do not clean brake parts with compressed air or by dry brushing. Cleaning should be done by dampening the brake components with a fine mist of water, then wiping the brake components clean with a dampened cloth. Dispose of cloth and all residue containing asbestos fibers in an impermeable container with the appropriate label. Follow practices prescribed by the Occupational Safety and Health Administration (OSHA) and the Environmental Protection Agency (EPA) for the handling, processing, and disposing of dust or debris that may contain asbestos fibers.
Inspect the fluid level in the brake master cylinder reservoir. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid needs to be removed from the reservoir before proceeding. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, remove brake fluid to the midway point before proceeding.
  1. Raise the vehicle and suitably support.
  2. Remove the tire and wheel assembly.
  3. Pull down on the front park brake cable.
  4. Remove the front park brake cable from the park brake cable connector.
    NOTE When using a large C-clamp to compress a caliper piston into a caliper bore of a caliper equipped with an integral park brake mechanism, do not exceed more than 1 mm (0.039 in.) of piston travel. Exceeding this amount of piston travel will cause damage to the internal adjusting mechanism and/or the integral park brake mechanism.
  5. Install a large C-clamp over the top of the brake caliper housing and against the back of the outboard brake pad. Compress the brake caliper piston into brake caliper bore to allow the piston enough clearance to slide the brake caliper off the brake rotor.
  6. Remove the C-clamp.
    NOTE Be sure to plug the opening in the brake caliper and brake hose to prevent fluid loss and/or contamination.
  7. Remove brake hose to caliper bolt attaching the brake hose to the brake caliper.
  8. Remove the brake hose from the brake caliper.
  9. Remove and discard the two copper brake hose gaskets. These gaskets may be stuck to the brake caliper and/or the brake hose end.
  10. Remove the park brake cable bracket from the brake caliper. Leave the park brake cable attached to the cable bracket.
  11. Disconnect the park brake cable from the park brake lever on the brake caliper.
  12. Remove the lower brake caliper pin bolt.
  13. Rotate the brake caliper up.
  14. Remove the brake caliper from the upper brake caliper pin bolt.
To install:
  1. If reusing the brake caliper retainers, clean the sleeves using denatured alcohol, or equivalent.
  2. Lubricate the brake caliper pin bolts with a thin coat of high temperature silicone lube.
  3. Install the brake caliper to the upper caliper pin bolt.
  4. Rotate the brake caliper down over the brake pads into the brake caliper bracket.
  5. Install the brake caliper pin bolts. Tighten the brake caliper pin bolts to 27 Nm (20 ft. lbs.).
  6. Remove the plugs in the brake hose end.
    NOTE Install NEW copper brake hose gaskets.
  7. Assemble the brake hose bolt and the NEW copper brake hose gaskets to the brake hose.
  8. Install the brake hose to caliper bolt to the brake caliper. Tighten the brake hose to caliper bolt to 44 Nm (33 ft. lbs.).
  9. Connect the park brake cable to the park brake lever on the brake caliper.
  10. Install the park brake cable bracket to the brake caliper. Tighten the park brake cable bracket bolt to 43 Nm (32 ft. lbs.).
  11. Install the front park brake cable to the park brake cable connector.
  12. Bleed the brake system.
  13. With the engine OFF, gradually apply the brake pedal to approximately 2 / 3 of its travel distance.
  14. Slowly release the brake pedal.
  15. Wait 15 seconds, then repeat until a firm brake pedal is obtained. This will properly seat the brake caliper pistons and brake pads.
  16. Install the tire and wheel assembly.
  17. Lower the vehicle.

NOTE The Bosch 2U ABS system cannot increase brake pressure above master cylinder pressure applied by during braking. There is no need to depressurize the system prior to service.
  1. Remove brake fluid from the master cylinder reservoir until the reservoir is approximately 1 / 3 full.
  2. Remove the front wheel. Mark the position of the wheel to the wheel studs, prior to removal, for installation reference.
  3. Install 2 lug nuts to retain the rotor once the caliper is removed.
  4. Using a large C-clamp, bottom the piston in the caliper bore by positioning the C-clamp on the outboard pad and on the round portion of the brake caliper where the piston is housed.
  5. Remove the banjo bolt that fastens the brake hose to the brake caliper. Discard the gaskets.
  6. Cap the brake line to avoid excessive fluid loss or fluid contamination.
  7. Remove the rubber dust boots from the caliper mounting bolt heads (if equipped).
  8. Remove the caliper mounting bolts.
  9. Remove the park brake cable from the caliper.
  10. Remove the caliper from the vehicle.
  11. Remove the brake pads.
To install:
  1. Install the brake pads. Lubricate the slides where the caliper mounts on the steering knuckle with silicone grease.
  2. Install the caliper over the rotor.
  3. Install the caliper mounting bolts. Torque the mounting bolts to 38 ft. lbs. (51 Nm).
  4. Install the park brake cable.
  5. Install the rubber dust boots over the caliper mounting bolt heads (if equipped).

    542f486.jpg
    Fig. Measuring the caliper clearance
  6. Check the clearance between the brake caliper and caliper bracket stops. If the clearance is too tight, check the caliper leading and trailing edges for build up. File down as necessary.
  7. Connect the brake hose to the caliper. Install the brake hose banjo bolt, using new gaskets, and torque to 33 ft. lbs. (45 Nm).
  8. Remove the lug nuts used to secure the rotor.
  9. Install the wheel, aligning the reference marks made during removal, and torque the lug nuts to 100 ft. lbs. (140 Nm).
  10. Refill the master cylinder and bleed the brake system using the recommended procedure.
  11. Road test the vehicle and check for proper braking performance

Hope helps (remember rated this).

Jul 08, 2010 | 2003 Pontiac Bonneville

1 Answer

Torque value on 2500 front brakes


Front caliper mounting bolts 24 ft/lb. support plate 43 ft./lb. hd front caliper adapter bolts 210 ft./lb. ld front adapter bolts 130 ft./lb. caliper banjo bolts 30 ft./lb.

Apr 01, 2010 | 2001 Dodge Ram 2500 Truck

2 Answers

Brake job torque spec


Caliper bolt 25 ft lbs/ caliper bracket bolt 79.6 ft lbs

Nov 13, 2009 | 2005 Honda Civic

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

Need the correct torque specs for 2004 silverado 1500 calipers


  • Tighten the 2 brake caliper mounting bolts to 108 Nm (80 ft. lbs.) . Caliper Mounting Bracket to Knuckle, Front (15 series) 175 Nm (129 ft. lbs.) Caliper Mounting Bracket to Knuckle, Front (25/35 series) 300 Nm (221 ft. lbs.) Brake Caliper Mounting Bolt Rear (15 series) 42 Nm (31 ft. lbs.) Brake Caliper Mounting Bolt Rear (25/35 series) 108 Nm (80 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JC5/JH5) 200 Nm (148 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH6) 165 Nm (122 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH7) 300 Nm (221 ft. lbs.) Caliper Mounting Bracket Bolt Rear (NYS) 200 Nm (148 ft. lbs.)
    hope this helps
  • Mar 28, 2009 | 2004 Chevrolet Silverado

    Not finding what you are looking for?
    1998 Ford Explorer Logo

    2,873 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    Marvin
    Marvin

    Level 3 Expert

    85239 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14866 Answers

    Mike

    Level 3 Expert

    4372 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...