What does the 12v wire look like for a 2000 kia sportage radio?

SOURCE: 2000 kia sportage ex, 4 cyl.

Yes there is a sensor that controls Fuel/air ratio.It's called a MAF (mass air flow sensor)
But I think you should have the EGR (Exhaust gas recirculation)valve checked
and The TPS (throttle position sensor)maybe dirty.

Although may things can cause this issue,I would look at the items above first.


Please rate this a blue fixya

SOURCE: the Abs light came on and will not go out after i

This is just a consequential event. the ABS sensor module was probably going out and decide the trigger the alarm at the same time you initiated the hard brake during travel. replacing or resetting this sensor module Will fix this issue. the light will go off as well.


Please rate and god bless.

SOURCE: I need radio wiring diagram for 2001 kia sportage

go to www.kiatechinfo.com sigh up it's free hope this helps

Greg Bernett

• 2993 Answers
• Posted on Oct 18, 2009

SOURCE: the easiest way to pull the heater core from a kia sportage-2000

There is no real easy way to do it....not like the older cars..

1. Disconnect the negative battery cable.
   
   CAUTION After disconnecting the negative battery cable, wait for at least 10 minutes for the air bag module to deplete its stored energy.
   
   
2. 1. Remove the driver’s side air bag and steering wheel by performing the following procedure:
   2. Position the front wheels in the straight-ahead position.
      
3. Remove the 4 steering wheel-to-air bag module bolts.
   
4. Carefully, lift the air bag module and disconnect the electrical connector.
   
   CAUTION Place the air bag module in a safe location with the front facing upward.
   
   
5. Remove the steering wheel-to-steering column nut.
   
   NOTE If may be necessary to mark the steering wheel to steering column alignment.
   
   
6. Using a steering wheel puller, press the steering wheel from the steering column.
   
7. Drain the cooling system into a clean container for reuse.
   
8. Discharge and recover the air conditioning system refrigerant.
   
1. Remove the instrument panel by performing the following procedure:
2. Remove both the rear and front consoles.
   
3. Remove the knee bolster assembly.
   
4. Remove the “T” bar section.
   
5. Remove the relay bracket.
   
6. Remove the turn signal assembly and the upper/lower steering column covers.
   
7. Remove the hood release handle lockscrew, the hood release handle and the cable assembly nut.
   
8. Remove the left side front pillar trim and the lower left side cover.
   
9. Remove the 2 left side of the “T” bar-to-chassis bolts.
   
10. At the left side of the instrument panel, remove the 3 instrument panel-to-chassis bolts.
    
11. Remove the ashtray.
    
12. Remove the center panel trim.
    
13. Remove the ventilation control panel.
    
14. At the center of the windshield next to the windshield, remove the cap and the mounting bolt.
    
15. " Remove the right side front pillar trim and the lower right side cover.
    
16. Remove the 2 right side of the “T” bar-to-chassis bolts.
    
17. At the right side of the instrument panel, remove the 3 instrument panel-to-chassis bolts.
    
18. Remove the steering column-to-instrument panel bolts and lower the steering column.
    
19. Disconnect the instrument panel electrical connectors.
    
20. Remove the instrument panel.
    
9. 1. Remove the blower/evaporator housing by performing the following procedure:
   2. Disconnect the air conditioning refrigerant lines from the evaporator core and discard the gaskets. Plug the openings to prevent contamination.
      
10. Disconnect the fresh air control cable from the blower/evaporator housing inlet duct.
    
11. Disconnect the 5 connectors from the bottom of the blower/evaporator housing.
    
12. Move the carpeting from the bulkhead to gain access to the hole cover plate.
    
13. Remove the 4 hole cover plate nuts and the plate.
    
14. Remove the 2 upper blower/evaporator housing bolts.
    
15. Remove the 2 lower blower/evaporator housing-to-bulkhead nuts.
    
16. Remove the blower/evaporator housing.
    
17. Disconnect the heater hoses from the heater core.
    
18. Remove the temperature control cable from the heater housing.
    
19. Remove the 2 lower heater housing nuts and the upper heater housing-to-bulkhead nut.
    
20. Remove the heater housing.
    

SOURCE: 2000 kia sportage radio unlock code

Vehcile stereo codes are different for every radio to deter theft. The codes are usually around 4 numbers. There are a couple ways to find out what your code is. First, check your owners manual, someone at some point may have written it down in there. Also, there may be a card somewhere in you paperwork that has the code. If you don't find the code, the easiest way to find out what it is, go to you local kia dealerships service department, if you give them you VIN number they will be able to give you the code (most of the time free of charge). My last suggestion, pull the radio out, sometimes it will be written on the unit.