Question about 1995 Mercury Villager

1 Answer

Okay so abs light is off but I am still pulling code 55 on a 95 villager can't figure out what going on need help

Posted by Shawn Muirhead on


1 Answer


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Mercury Master
  • 5,692 Answers

The Code shows Bank 1 Sensor 3 for the O2 system. That the wire going to that part is broken or disconnected.

Posted on Jun 04, 2015


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My abs light is on in my 95 villager as well as my check engine light, I got a trouble code of 55 I replaced the brakes still can't get rid of abs light or check engine light what can the problem be?

code 55 on a 95 villager means "no codes found". If you are getting this code but the check engine light is on as well as the ABS light, then there is a good chance there is a problem with the ABS system itself. Manufacturers will often set it up so that multiple trouble lights will turn on to get your attention in the event of a major problem. If these lights are on together but you are getting 55, you will need to check the ABS system. It could be low brake fluid, or a problem with the ABS pump... There is also a chance that there is a blown fuse for either the ABS system or the diagnostics system which could also cause lights to turn on. One other possibility is that they are on for a factory set maintenance/service interval, meaning Mercury may have set these lights to turn on at a pre set mileage so that you will have the ABS system inspected at that point, although I don't believe this was very common in 95. My best advice is to check your fuses and fluid level, if none of these are the problem it might be a good idea to seek the help of a professional garage, you should never take chances when you're brakes are involved. Good luck :)

Apr 07, 2015 | Cars & Trucks

1 Answer

Abs light

The warning light has very little to do with the hydraulic brake system.
The ABS system uses the hydraulic system to prevent the brakes from locking up.
You would need to have the body computer scanned for trouble codes to proceed with repairs.

Aug 25, 2012 | 2002 Mercury Villager

2 Answers

Need to reset abs light on a 97 gmc sonoma truck

If the abs light is on than there is a problem with the abs. If the problem was fixed the light would go out on it's own once the self test completed successfully when you started the vehicle. If you have not pulled codes or made a repair than turning off the light with a scan tool capable of reading abs data will only result in the light coming back on when the abs module still sees the fault present when you start the vehicle the next time. The first thing to do is find out what codes are present. Then focus on that part of the abs system. If you know the code or find out what the code is post it and I'll help you figure it out.

I’m happy to assist further over the phone at

Sep 01, 2011 | GMC Sonoma Cars & Trucks

1 Answer

Abs wiring diagram

I have wring book and shop manual for $25.

Also, go to our site for help. What is the issue? ABS pretty relaible in Villager & Quest.

Nov 30, 2010 | 1994 Mercury Villager

2 Answers

Driver's seat won't move and ABS lights come on

See if one of the wires under the seat is pinched and shorting out. The abs light maybe a dirty sensor.

Jun 28, 2010 | 2003 Ford Windstar

1 Answer

Anti loc brake problem

when the abs light comes on that disables the abs wich frees up your brakes u will need to go to the shop and have a code pull done on your car to figure out what is setting the abs code

Mar 15, 2010 | 2000 Jeep Grand Cherokee

1 Answer

My villager would not start unless I jump it. As I drive the abs light comes on and the car feels like its going to stall. I put it in park and it died.

If you have to jump the battery, then either the altenator or voltage regulator (built in altenator) is bad. Most part stores will test it for free. Even in the vehicle. Either the altenator/regulator is bad, or there is a short draining the battery.
The is a seperate issue. Could be bad abs pump or circuit which will have to be diagnosed with a code scanner or engine diagnostic machine just for abs systems.

Nov 15, 2009 | 1996 Mercury Villager

1 Answer

ABS light

It is picking up a signal from one of the wheel sensors probably.

Go here to read files on ABS issues

  • Anti-Lock Brake Warning Indicator Always On
  • Fuse(s).
  • Circuit.
  • Hydraulic solenoid relay.
  • Hydraulic pump motor relay.
  • Brake anti-lock sensor(s).
  • Hydraulic anti-lock actuator assembly.
  • Anti-lock brake control module.
  • GO to ABS Quick Test .

  • Key OFF.
  • Jump Pin 4 of the data link connector to ground.


  • Key ON.
  • Observe the anti-lock brake warning indicator.
NOTE: The first code to flash will be the start code (12). Also, each code is repeated three times before proceeding to the next trouble code.

Does the anti-lock brake warning indicator flash codes? Yes No RECORD code(s). GO to the following ABS Trouble Code Identification Chart in this section and PERFORM Pinpoint Test specified for first code retrieved. If indicator is illuminated constantly, GO to Pinpoint Test D1 . If indicator is not illuminated, GO to Pinpoint Test A1 .


Jan 02, 2009 | 1993 Mercury Villager

3 Answers

Abs warning light

you need brake fluid.

Aug 01, 2008 | 1999 Chevrolet Cavalier

Not finding what you are looking for?
1995 Mercury Villager Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides