How do I open the rear cargo door if neither electric switch nor door key will open it?

NO CAR TOLD AT ALL.
sounds SUV ,UTE, OR VAN LIKE (CARGO)

Service repair info. manual would be the place to start ,seeing how you have no clue .,or maybe a qualified repair shop. How are you going to fix it with out knowledge of how it works an what to check , --------------------------------------------------------------------------------
Power Door Locks Circuit Description
The power door locks are operated by reversible motors. The motors are found in the following locations:
• In each front door
• The side door
• The rear door
The PWR ACCY circuit breaker (30A) supplies voltage to the door lock motors.
If you move either power door lock switch, mounted in the front doors, the LOCK applies voltage to cavity F of the door lock relay. This energizes the lock coil in the relay. Current then flows through CKT 295 (GRY) directly to the following components:
• Both front door lock motors
• The side door lock motor
• The rear door lock motor (cargo doors only)
CKT 246/294 (TAN) provides the ground for the motors. The normally closed contacts of the UNLOCK then contacts the door lock relay.
If you move one of the door lock switches to UNLOCK the polarity of the system reverses. Current flows through the energized UNLOCK relay contacts. The LOCK relay contacts provide ground.
When the UNLOCK button is pressed once on the RKE transmitter, only the driver door unlocks. If it is pressed a second time within 5 seconds, all doors unlock.
If the side door is open, the side door jamb switch ground signal is opened/broken. If you move the door lock switch to LOCK while the side door is open, the following actions occur:
• The 2 front doors lock
• The rear door locks (cargo doors only)
When you close the side door, the door jamb switch closes. This closes the ground signal to the body control module {CKT 775 (PNK)}. A 5 second timer then starts in the module. After 5 seconds, cavity A4 connector C1 of the body control module supplies voltage to the door lock relay via CKT 195 (LT BLU). This energizes the door lock relay, which sends voltage to the door lock motors in order to lock the side door. Refer to Door Jamb Switches, Liftgate Strut Switch for a schematic of all door jamb switch inputs.
If the side door opens during this 5 seconds, the 5 seconds timer is reset. The locking pulse takes place at the end of the 5 seconds. Unlocking the door resets the 5 second timer in the body control module.
Use the following components in order to unlock the door lock system:
• The LH power door lock switch
• The RH power door lock switch
On vehicles equipped with cargo doors, the cargo door opener mechanically opens the door once the door lock system is unlocked. On vehicle equipped with a liftgate, the liftgate lock/unlock release switch (mechanical key) is added in order to serve the same function as the front power door lock switches. These functions locking and unlocking all doors, including the liftgate. Once the door lock system is unlocked, press the liftgate release switch in order to electrically open the liftgate and pull the handle in order to open the secondary latch.

SMART ENTRANCE CONTROL UNIT PFP:28596 Description EKS003A2 OUTLINE The smart entrance control unit totally controls the following body electrical system operations. ? Warning chime ? Rear window defogger and door mirror defogger ? Power door locks ? Remote keyless entry system ? Vehicle security system ? Interior lamp ? Battery saver control BATTERY SAVER CONTROL Interior Lamp/Map Lamp/Vanity Lamps The lamps turn off automatically when the interior lamp, map lamp or/and vanity lamps are illuminated with the ignition key in the OFF position, if the lamp remains lit by the door switch open signal or if the lamp switch is in the ON position for approximately 10 minutes. After lamps are turned off by the battery saver system, the lamps illuminate again when: ? Driver's door is locked or unlocked, ? Door is opened or closed, ? Key is inserted into or removed from the ignition key cylinder. Rear Window Defogger/Door Mirror Defogger Rear window defogger and door mirror defogger are turned off approximately 15 minutes after the rear window defogger switch is turned on.

Warning chime Key switch (Insert) Ignition switch (ON) Lighting switch (1st or 2nd) Seat belt buckle switch LH Front door switch LH Warning chime (located in smart entrance control unit)

Does it have power locks ?

TIME CONTROL UNIT PFP:28491 Description (Without Power Door Locks) EKS003A6 OUTLINE The time control unit totally controls the following body electrical system operations. ? Warning chime ? Rear window defogger INPUT/OUTPUT System Input Output Warning chime Key switch (Insert) Ignition switch (ON) Lighting switch (1st or 2nd) Seat belt buckle switch LH Front door switch LH Warning chime (located in time control unit) Rear window defogger Ignition switch (ON) Rear window defogger switch Rear window defogger relay

key is manual lock and electric assisted unlock . charge the battery with red screw on fuse panel Use key to unlock turning to rear.
Place key in ignition then turn on and off 8 times leaving it in on position until it beeps approx 5 sec then press any button on the key and turn ignition off.

Power Door Locks Circuit Description
The power door lock system incorporates door lock switches on both front doors and on the RH D-pillar, door lock motors in all passenger doors and in the RR cargo door, a door lock relay and a door lock control module.
Power for the door lock switches and the door lock control module is supplied from the CIG LTR fuse 13 through CKT 640 (ORN). Power for the door lock relay is supplied from the PWR ACCY circuit breaker through CKT 540 (ORN). Ground for the door lock relay is supplied from G202 through CKT 150 (BLK) and ground for the door lock control module is supplied from G400 through CKT 150 (BLK).
The door lock motors are reversible and both sides are connected to the normally closed contacts of the door lock relay. Those contacts of the relay are connected to G202. When any of the door lock switches are placed in the lock position, voltage is supplied through CKT 195 (LT BLU) to the relay lock coil. Since the other side of the lock coil is connected to ground, the coil is energized and it pulls the lock contacts closed. Voltage is then supplied through CKT 295 (GRY) to all the door lock motors and the doors lock. The unlock function operates in much the same manner except that when any of the switches are placed in the unlock position, voltage is supplied through CKT 194 (WHT) to the unlock coil of the relay and CKT 294 (TAN) supplies voltage to the apposite side of the door lock motor and the doors unlock.
Door Lock Control Module Description
The door lock control module is used on vehicles equipped with cargo doors. The purpose of the module is to lock the cargo doors after a lock cycle has been commanded from any of the door lock switches with the cargo doors open. When the RH cargo door is open, the module receives a ground signal from the closed contacts of the rear door jamb switch on CKT 1897 (ORN/BLK) to G400. When a lock command is received, the module retains this input until it receives an open input from the rear door jamb switch. Then the module sends a lock command through CKT 194 (WHT) to the door lock relay and the doors lock.
Rear Cargo Doors Description
The power door lock motor will not operate unless the rear cargo doors are fully closed. The power door lock motor is in the right cargo door. The contactors are on the rear cargo door opening on the body and on the right cargo door.

the electric door lock button should unlock the rear lift gate.

U will have to open th door from th in side. To unlock it. Remove the inside panel. And where th key go, u can unlocked from th inside. But firs try to lock and unlock th door whit th electric control while u try to open th door. Because sometimes they are just stock and need lubrication. Good lock

possibly it still thinks a door is open check out rear cargo door switch this is usually the culprit because its seperate from the rest of the doors. turn on rear cargo light to doors ,make sure it works then shut rear cargo door and see if light is still on. if light is still on theres your problem.
look at switch usually they get dammaged/distorted over time.

Hi! Yes its possible if manual you want it to be. Try this, If the cargo doors have separate fuse from the fuse box then just remove the fuse and it would work manually. If you wont find the door fuse then you should work on the door manually. Open the cargo door trimming and you will find a motor inside the door. The motor has a connector that leads to the lock. Remove the connector to cut the power supply to the motor and you'll be on manual now. Hope this helps and have a good one!

Hello! The instigator of this problem appears to be the the rear cargo lamp; Official name is rear dome light. You'll need a multimeter set on the X10 ohm scale to shoot this trouble. Leave the rear dome light bulb out. There are two switches involved; #1 the rear dome light on/off. #2 the right hand front door switch.

Pull the horn fuse out, remove the rear dome light cover, drop the rear dome light down to access the wiring and close all doors on the vehicle. Connect one lead of the ohm meter to the white wire and the other to body ground. If you read any resistance one or both of the two switches (dome light switch or right hand front door switch) is remaining closed when all doors are closed. Next disconnect the black lead from the dome light switch and see if reading changes to zero. If it does this is indicating that the dome light switch is defective. If it does not, disconnect the right hand door switch and take another reading at the same location. If you still measure any resistance, the black wire of the rear dome light is shorted to ground, if not then the right hand door switch is the culprit.

The reason the right hand door switch and not the left hand door switch is involved is the fact that opening the left front door would turn on the front dome light as well as the rear light. If both dome lights are staying on with all doors closed I would then involve both door switches in this test procedure. If your vehicle is a four door model then disconnect one door switch at a time while performing this test procedure.

The horn fuse also supplies power to the rear dome light, and I suspect the two events are related.


Guru..............saailer


I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867