Question about 2006 Chrysler 300

1 Answer

Just change fuel pump an still won't start. - 2006 Chrysler 300

Posted by daniel ozane on

Ad

1 Answer

Shade Tree All Repair

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 509 Answers

This will take several tests so when you have time let me know and we will begin. If your advanced enough I will lay out a few tests.
1. When you turn on the key do you actually hear the pump working?
2. Make sure the connection to the new fuel pump is tightly put together and saftey pin is put back in and if still possible to access wiring still test for power to the pump with wire tester or ohm meter in the connection union.
3. If not check all fuses under the hood and inside the car, make sure they are good whth a test light or ohm meter.
4. Have the fuel solenoid checked or basically purchase a new on they are not expensive anyway.
5 have scanner put on the car make sure all the Cam Sensor,,Crank sensor, Throttle Position Sensor etc, we are looking for any item caught in live data or engine light is on.
6. Make sure battery is connected tightly and is fully charged (FULLY CHARGED) a weak battery reaks havoc on an electrical system. I am fully positive doing the 6 stages you will find your problem I assure you, and you can get a cheap 40 dollar OBD scan tool code reader at autozone or where ever you may shop.
After before all this make sure the security has not been triggered during your work with the new pump!! if it has cycle the remote with full lock and unloce 1 with the key cycle it un and lock with remote is first then lock with remote and open with key. should solve this problem for you.
anything else just ask. thanks the fixya team

Posted on May 22, 2015

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I changed the fuel pump but the van still won't


And you know the fuel filter is good? Could be injector problem: just as a check, spray some starting fluid into the intake and see if engine runs a few seconds. If it does, it is a fuel problem. Check injector fuse, as a start. Check fuel pressure. Check injector circuit. If engine won't start with starting fluid, check if you are getting spark. Problem may be in the ignition system.

Aug 13, 2013 | Cars & Trucks

1 Answer

I have a 1999 Honda accord LX coup I changed the fuel pump and now my car still won't start ? Also I changed the fuse same thing won't start can some on help me please ??????


Ignition switch was my problem after changing fuel pump and main relay. Then had to have transmission rebuilt, all of this was back to back.

Aug 10, 2013 | Cars & Trucks

1 Answer

It won't start I change fuel pump


What is the make model and year, and does the engine have fuel pressure now that you have changed the pump ?

May 03, 2013 | Cars & Trucks

1 Answer

Car Won't Start!!


could have plugged fuel filter check see if you have fuel pressure.if no check fuel pump fuse or relay.

Apr 26, 2013 | Cars & Trucks

1 Answer

My 2004 chevy venture won't start. Changed the


Did the fuel pump come on?

Did you check fuel pressure at the motor?


Try jumping the relay to get pump on?

Read a wiring diagram-- so you know what your doing?

Check Power & Grounds to pump when the tank was down?

Dec 22, 2012 | Cars & Trucks

1 Answer

93 chrysler t&c awd changed fuel pump and filter, van ran fine again for about 2 months now won't start and don't hear the fuel pump. changed the oil pressure sending unit and still won


fuel pick-up in tank is blocked it has a sock over the end as a gross filter to keep out any big junk from getting sucked into the pump and causing damage to it. the sock can get so plugged up that no fuel will flow, causing the pump to run for a short time then with no fuel flow to cool it it trips the safety and shuts off

Aug 12, 2012 | Cars & Trucks

1 Answer

Car won't start; mechanic said it was fuel pump; fixed problem but car still won't start...any suggestions of what could be?


When you changed your fuel pump did you also change the fuel filter? If not, that would be the next logical step. While you have it disconnected you can also check to make sure the fuel pump is pumping the fuel.

Aug 18, 2011 | 1997 Ford Expedition

1 Answer

My ford expedition won't start i change the fuel


If it a diesel then you must be aware that when changing a filter and pump they must be full of fuel, otherwise it won't **** the fuel into the engine.

Jul 11, 2011 | 1997 Ford Expedition

1 Answer

My 2000 buick lesabre want start fuel pump comes on when i turn the key i have spark at the coils.checked all fuses. Changed fuel filter but car still won't start its trying to start but just...


It could be the fuel pump. Sometimes you can hear them engage, but they are not pushing enough fuel pressure to run the car. This can be checked.

Jun 16, 2011 | Buick LeSabre Cars & Trucks

3 Answers

1995 e34 520i won`t start


i would check the fuse for the fuel pump and the relay.

May 26, 2008 | 1994 BMW 5 Series

Not finding what you are looking for?
2006 Chrysler 300 Logo

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...