Power flows from the battery to the main fuse. Then it flows to the control coil and contact side of the headlight relay. When you turn on the headlights, the headlight switch provides ground to the control coil in the headlight relay and that operates the contacts. The contacts allow power to flow to the right and left hand headlight fuses. Power flows to the headlights. The headlight switch is what provides ground to the high and low beams on the headlights.
To diagnose, remove the headlight relay. Using a voltmeter, check for battery voltage on terminals 3 & 4 in the socket with the key in the RUN position. Then turn on the low beams. Test for good ground on terminal 1 in the socket. If you're not getting ground, then you've got a problem with either a bad headlight combo switch or a bad ground. If you get good ground on terminal 1, reinstall the relay, turn on the low beams and test for power in the headlight sockets. If you get battery voltage, that confirms you've got good fuses and wiring up to that point. Next, check for good low beam ground on the red/green wire in the bulb socket. If you're not getting good ground, it's either a bad combo switch or bad ground from the combo switch. Then turn on the high beams and check for good ground on the red/yellow wire in the bulb sockets.
It wouldn't hurt to clean the ID ground on the left side of the instrument panel, but based on everything you've said so far, this sounds like a bad combo switch
Power flows from the battery to the main fuse. Then it flows to the control coil and contact side of the headlight relay. When you turn on the headlights, the headlight switch provides ground to the control coil in the headlight relay and that operates the contacts. The contacts allow power to flow to the right and left hand headlight fuses. Power flows to the headlights. The headlight switch is what provides ground to the high and low beams on the headlights.
To diagnose, remove the headlight relay. Using a voltmeter, check for battery voltage on terminals 3 & 4 in the socket with the key in the RUN position. Then turn on the low beams. Test for good ground on terminal 1 in the socket. If you're not getting ground, then you've got a problem with either a bad headlight combo switch or a bad ground. If you get good ground on terminal 1, reinstall the relay, turn on the low beams and test for power in the headlight sockets. If you get battery voltage, that confirms you've got good fuses and wiring up to that point. Next, check for good low beam ground on the red/green wire in the bulb socket. If you're not getting good ground, it's either a bad combo switch or bad ground from the combo switch. Then turn on the high beams and check for good ground on the red/yellow wire in the bulb sockets.
It wouldn't hurt to clean the ID ground on the left side of the instrument panel, but based on everything you've said so far, this sounds like a bad combo switch
×
SOURCE: Headlights
I READ ONLINE THAT THERE WAS A RECALL ON THIS YEAR AND MAKE, CHECK WITH TOYOTA WEB SITES TO RECTIFY YOUR PROBLEM
SOURCE: Headlight 2004 camry
your module in the steering wheel is faulty you should get it replaced. you can purchase it at ie Napa for alot less than through a dealer.
SOURCE: 1992 toyota corolla
Sorry, was not available at your time. Since the blue light comes on, this tells me that the hi-beam fuse is good. Go to the pass side headlamp, and, behind it, remove the connector for the inop bulb, and remove the bulb. Examine the filament on the bulb. Is it broken in half? If so, you need two hi-beam bulbs. Get back to me if you need more info.
SOURCE: Low beam headlights don't work
I have e-mailed you 2 .pdf files, one is the complete headlamp diagram, and the other is the relay locations. Please advise if you need further assistance.
Toyota Ed
SOURCE: Low Beam Headlights Not Working
to troubleshoot i would suggest buying a new headlight if the new one works just buy the other one it is not uncommon for just one beam to go out hope this helps regards jim
628 views
Usually answered in minutes!
×