Where is the remote keyless entry module receiver

According to GM there are 3 components in the RCDLR or RKE remote keyless entry system. My key fobs with new batteries only work standing right next to the car. The range of the key fob dropped at that the same time my TPMS tire pressure monitoring system repair warning came on my dashboard. The problem is that there are 4 different components on the 2015 Malibu. I will provide the GM part numbers for these, if you please tell me where they are and also how to replace them: #13583559 Remote Control Door Lock Receiver #13502554 Antenna #13502551 Ignition Lock Key Transmitter Antenna #13502549 Low Frequency Console Antenna

The remote keyless entry (RKE) module for a 2010 Volvo S80 V6 is typically located in the trunk of the vehicle, near the spare tire. It is a small module that is responsible for controlling the functions of the remote keyless entry system, such as locking and unlocking the doors, activating the alarm, and starting the engine using the remote.
To locate the RKE module, you may need to remove the trim panel or carpeting in the trunk. If you are unable to find the module or are unsure of its location, you may want to consult your owner's manual or a repair manual for your specific model of Volvo S80. Alternatively, you can try contacting a Volvo dealership or a mechanic for assistance.

Could not find specifics for the 2013, but earlier caravans have the remote keyless receiver (RKE) built into the functions of the Body Control Module (BCM) which is located behind/part of the passenger compartment fuse box ... located under the dash down to the left.

None of the door power lock's work ? Not from any switch ? F32 - 15 amp fuse location - body control module (BCM) . Probably not a fuse issue , door locks are controlled by the BCM controlling relay's located inside the BCM . This relay's are PCB - printed circuit board relay's , non serviceable . Your best bet , take it to a qualified repair shop .

Power Locks
The Body Control Module (BCM) monitors the door lock control switches. When the BCM receives an unlock/lock command from either door lock control switch, the BCM energizes a relay (internal to the BCM ) to supply the correct power and grounds for the door lock actuators.

Remote Keyless Entry (RKE)
The Remote Keyless Entry (RKE) feature is controlled by BCM . The BCM receives the RKE inputs from the Tire Pressure Monitor (TPM) module over the Medium Speed Controller Area Network (MS-CAN) . When any RKE transmitter button is pressed, the signal is received by the TPM module internal antenna. The TPM module then filters the RKE signal received to make sure it is a programmed transmitter. If the signal received is from a programmed transmitter, the TPM module sends the RKE command to the BCMover the MS-CAN . The BCM then interprets the RKE command and activates the corresponding output.
The BCM requests the illuminated entry feature to turn the interior lamps on when an unlock command is received. If a lock command is received, the illuminated entry feature turns off. The BCM then supplies voltage to the appropriate door lock actuator(s) to lock or unlock the doors. The RKE transmitter can also be used to activate the panic alarm. On vehicles with memory, the RKE transmitter also causes the BCM to send a MS-CAN message to the Driver Seat Module (DSM) to activate all memory features to the positions associated with the RKE transmitter being used.

Visual Inspection Chart

Mechanical Electrical

• Door handles
• Binding latch mechanisms

• Body Control Module (BCM) fuse(s):
  • 18 (10A)
  • 20 (20A)
• Wiring, terminals or connectors
• Door lock control switches
• Keyless entry keypad
• Integrated Keyhead Transmitter (IKT)
• BCM

Do you know what DTC'S are ?
DTC Charts
GO to Pinpoint Test H.B1218: 00Transmitter Identification Code: No Sub Type InformationGO to Pinpoint Test H.B121A: 11Keypad Illumination Output: Circuit Short to GroundGO to Pinpoint Test G.B121B: 01Keypad Input Switch: General Electrical FailureGO to Pinpoint Test F.B126A: 01Drivers Door Interior Lock Switch: General Electrical FailureGO to Pinpoint Test E.B130D: 00Memory Full for Integrated Key Programming: No Sub Type InformationThe maximum amount of IKTs (4) have been programmed into the BCM . Obtain all the customer's IKTs . Erase all the IKTs and program a maximum of 4.All other DTCs-REFER to the Diagnostic Trouble Code (DTC) Chart in Section 419-10.

The RKE is controlled by the SJB - smart junction box ! Fords BCM - body control module .
Principles of Operation
Power Locks
The SJB controls the power lock/unlock feature of all of the vehicle doors, including the liftgate, to lock or unlock based on the input received from the door lock control switch, the keyless entry keypad or the remote keyless entry (RKE) transmitter. Power locking and unlocking of the doors function independently of the key position, vehicle speed or transmission position. The smart junction box (SJB) activates internal relays to supply the correct voltage and grounds for the door lock actuators.

Your best bet would be to take to ford dealer or some other qualified repair shop .
Remote Keyless Entry (RKE) Transmitter Lock/Unlock Control - Unlock
The RKE transmitter feature provides lock/unlock functions independently of key position, vehicle speed, or transmission position. The RKE transmitter feature provides a 2-step process for unlocking the doors. Upon receipt of the first request for unlocking the doors, the RKE control feature requests the SJB to unlock the driver door only. If another unlock request is received within 3 seconds of the first, the RKE transmitter feature requests the SJB to unlock all the doors. This feature can be changed to global unlock, so that all the doors unlock on the first press of the unlock button. To toggle between the 2-step unlock and the global unlock press the lock and the unlock button on the RKE transmitter at the same time and hold the buttons for 4 seconds. The turn signal lamps flash to confirm that the feature has been toggled.
Remote Keyless Entry (RKE) Transmitter Lock/Unlock Control - Lock
The RKE transmitter feature requests that all the doors be locked when the lock button is pressed. On any press of the lock button with all doors closed, the SJB provides 1 flash of the parking lamps. If any door is ajar, no flash occurs. As soon as the last door is closed, the SJB provides the flash of the parking lamps. If 2 presses of the lock button are received within 3 seconds, the horn chirps once, and the parking lamps flash twice to indicate that all the doors are closed and locked. If any door is ajar when the second lock request is received within 3 seconds of the first, the RKE transmitter feature requests the SJB chirp the horn twice without flashing the parking lamps to indicate it locked all the doors but 1 or more doors are ajar. When the key is in the ON or START position, the parking lamp flashes and horn chirp confirmations do not occur.

All locks not working ?????

• The doors do not lock/unlock using the remote keyless entry (RKE) transmitter

• RKE transmitter battery
• RKE transmitter
• RKE transmitter programming
• Aftermarket system
• SJB

• Go To Pinpoint Test H .

RKE means remote keyless entry. Install a new battery in your key fob and your light will go off. Regards, Joe
ps - kindly rate my answer as helpful. thank you.

hi, this is a common problem and the only way of solving it is by taking your car to your nearest main dealers and then get them to re-programe the keyless entry for you they should do this for free but this is the only way you can get this done due to the fact of crminals being ablt to re-programe their own remotes to open other peoples cars so thats why its only the main dealers that can do this.

Let me know how you get on or if you need further assistance ok

www.OriginalKeyless.com

www.Keyless-Remotes.com

www.ikeyless.com/Lexus

motors.shop.ebay.com/i.html?_nkw=lexus+keyless+remote

sfbay.craigslist.org/eby/pts/1431366463.html

Dealer only.