Cars & Trucks Logo

Related Topics:

R
Roderick a fraser Posted on Mar 27, 2015

Manual dodge ram 50 pickup truck 4 cylinder - 1987 Dodge Ram 50

  • gbob59 Mar 27, 2015

    Hi Roderick a fraser, I want to help you with your question, but I need more information from you. Can you please add details in the comment box?

×

5 Related Answers

Anonymous

  • 490 Answers
  • Posted on Apr 13, 2009

SOURCE: 2001 Dodge Ram 1500; how to reset computer after replacing dead battery

disconnect the positive battery cable for 2 minutes and that will reset the computer

Ad

Anonymous

  • 38 Answers
  • Posted on Sep 14, 2009

SOURCE: Firing order & diagram for distributor cap for

It is 1-8-4-3-6-5-7-2 with 1-3-5-7 on the drivers side front to back, 2-4-6-8 on the pass side and the dist turns clockwise.
I wish I still had my Chilton's manual, I would scan a picture for you.

If this helps, please rate me.
Thanks,
Matt

Testimonial: "Just the info I needed, THANKS VERY MUCH."

Anonymous

  • 52 Answers
  • Posted on Feb 17, 2010

SOURCE: 2000 dodge truck code po203 po204

p0203 injecter circuit malfunction cyl #3. p0204 injector circuit malfunction cyl#4. po138 02 sensor circuit,high voltage cylinder bank no.1,sensor no.2

Anonymous

  • 593 Answers
  • Posted on Apr 10, 2010

SOURCE: Remove headlight assembly from a 2001 Dodge Ram

On the upper grill side of the headlight assy. there
should be 1 or 2 push pins that hold the seal on the
headlight assy to the front of the fender. Also check
for a guide/push pin on the inner top of the assy on
the outer fender side. That should be all there is to
hold the headlight in place. Hope this helps.

Anonymous

  • 666 Answers
  • Posted on Jun 13, 2010

SOURCE: where is the fuel filter in a 1995 dodge ram 1500

On the frame rail near tank

Testimonial: "Hey I've been looking for this answer for hours then I ran across this site and whattya know an answer almost nstantly Thank You"

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Have a dodge ram 50 pickup.. Hard to start.. Once started it will idle... Try to pull out and it hesitates and wants to die.. Back off on the gas and sometimes it will idle or dies..

Dodge Ram 50 Pickup Questions - Page 5 - CarGurus

www.cargurus.com > Questions > Dodge

CarGurusGet fast answers to your Dodge Ram 50 Pickup questions from experts in the ... 1986 Dodge Pick Up 5.9 Wont Start I Put New Distributor Set The Timing, New.

Dodge Ram 50 Pickup Questions - Carburetor - CarGurus

www.cargurus.com > Questions > Dodge > Ram 50 Pickup

CarGurusCarburetor - I recently bought a 1989 2.6L Ram50 for my son. ... Asked by redoverfarm Apr 13, 2010 at 03:36 PM about the 1989 Dodge Ram 50 Pickup ... check your fuel injector...may be clogged dirty, get a fuel injector cleaner or carburator ... Also gets poor gas mileage and is hard to start when the engine is warm !

Dodge Ram 50 Pickup Questions - 87 d 50 2.0 runs ok ...



89 Ram50 wont start.. - DodgeTalk : Dodge Car Forums, Dodge Truck ...

www.dodgetalk.com > ... > Dodge Ram Truck 1st Gen (88 - 93) Forum
Sep 22, 2011 - Hey guys i got a 1989 Ram 50 and im hoping i can get some help here. She drives like a champ but she only starts when i push start it, once i ...
0helpful
1answer

Key is stuck in ignition receiving no electricity

You are not the only one:

Key stuck in ignition, wont start, dodge ram pickup - Fixya

www.fixya.com/.../t14560159-key_stuck_in_ignition_wont_start_dodge
Oct 6, 2012 - key stuck in ignition, wont start, dodge ram pickup - Dodge Ram 1500question. ... 631 Answers. SOURCE: 1999 Dodge Ram 1500 Pickup error code p0171. This code means ... Jun 28, 2011 ' 1987 Dodge Ram 50 · 1 Answer .
0helpful
1answer

Free online auto repair manuals

Go to Helm.Com

Spend the big dollars & buy the factory manuals,
that are of value to you.

Anything free or any other source of info, is useless
& of no value & may not even match your vehicle

I have 50 years experience with new vehicles & Helm
Factory manuals
1helpful
1answer

2001 ram 1500:3.9l v6 2wd. I have trouble codes p0300:p0303:p0304 coming up how do I fix them and would they cause my truck to bog down around 50 mph? It runs good and strong under 50 but slow to pickup...

code 300 random cylinder misfire, code 303 cylinder 3 misfire detected code 304 cylinder 4 misfire detected. check the spark plug wires 3 and 4 inline tester for constant fire. also check the spark plugs , clean and reset the gap if necessary. if all is good check the coil terminals for corrosion. if this is all correct then check the coil with a ohm meter for primary resistance by attaching the leads to the positive and negative terminals. then check the secondary resistance by hooking one of the ohmmeter leads to the center terminal and the other lead to one of the outer terminals the resistance for primary test should be 0.95 to 1.20 ohms and the resistance on the secondary side should be 11,300 to13,300 ohms. hope this will help!!!
0helpful
2answers

Where is the EGR valve on 1986 Dodge Ram D50 pickup 2.0cc 4 cyl

if there pipes or tubes on top of your exhaust manifold that is where your EGR valve should be. if you want diagrams or text to help fix this problem i suggest the book from Chilton. they tend to explain thing pretty well.
8helpful
1answer

Firing order & diagram for distributor cap for 1985 Dodge Ram 50 Pickup with a 318 cid engine

It is 1-8-4-3-6-5-7-2 with 1-3-5-7 on the drivers side front to back, 2-4-6-8 on the pass side and the dist turns clockwise.
I wish I still had my Chilton's manual, I would scan a picture for you.

If this helps, please rate me.
Thanks,
Matt
1helpful
3answers

I need to know the firing order for a 1987 dodge ram 50 2.0 4cyl

I dont know of a dodge ram with a 2.0 liter. I know the 2.0 liter was in the colt vista. But the firing order of a 1987 2.0 liter is 1342.
4helpful
3answers

Hi, do you have the firing order on a 1989 Dodge D50 2.0L 5 speed

If it has the Mitsubishi 4 cylinder motor It's 1-3-4-2
If it has other,Please specify
0helpful
1answer

Put new oilpump and hadto remove timeing belt and gears. i need t

For the 1986 Dodge Ram 50 2.0L AND 2.6L 4-Cylinders:

Firing Order:
1-3-4-2

Cylinders:
(back)
...4
...3
...2
...1
(front)

Distributor:
.(back)
3.......4
1.......2
.(front)

For the Timing Marks: Click on the following Link. It has the Position of the Cranshaft and Camshaft and their respective marks.

http://www.2carpros.com/car_repair_information/year/1986/make/dodge/model/ram_50/1986_dodge_ram_50_timing_belt_diagram_marks.htm
Not finding what you are looking for?

179 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...