Question about 2011 Chevrolet HHR

Open Question

The light bulb in gear shift console burned out. How do I replace it?

Posted by Cheryl on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 buick lacrosse console gear indicator bulb


Transmission Floor Shift Control Indicator Lamp Replacement

Remove the front floor console. Refer to Front Floor Console Replacement.
Rotate the floor shift control indicator lamp socket (2). Pull the socket from the trim bezel.
Remove the bulb from the socket.

Front Floor Console Replacement

Preliminary Procedures
Remove the rear floor console. Refer to Rear Floor Console Replacement.
Remove the instrument panel lower trim plate. Refer to Instrument Panel Lower Trim Plate Replacement.
Set the parking brake, then shift the transmission into drive and push the shift indicator down until it locks, to allow clearance to remove the console.
1
Front Floor Console Screw (Qty: 2)
Caution: Refer to Fastener Caution in the Preface section.
Tighten
2 N·m (18 lb in)
2
Front Floor Console Bolt (Qty: 2)
Tighten
10 N·m (88 lb in)
3
Front Floor Console Assembly
4
Front Floor Console Retainer Clip (Qty: 2)

Feb 24, 2017 | 2009 Buick LaCrosse

2 Answers

Where can I buy light for Chevy cobalt gear shift console


Most console bulbs are 194. Napa or any parts store.

Apr 14, 2015 | 2008 Chevrolet Cobalt

1 Answer

How to replace light burned out on gear shift console 2008 corolla


Dores the 09 corolla have a bulb or is it an electrical thing under the gear shift console?

Mar 13, 2012 | 2008 Toyota Corolla

1 Answer

How do you replace drive indecator light


1. Lift the little carpet in the console rear to the automatic gear shift. Pry with a small flat screwdriver will do the job.2. Remove the three Philips head screws.3. Remove one Philips head screws on each side of the rear console, they are located at the bottom front of the rear console panel. You may have to move the driver and passenger seat back to see the screws.4. Grab the back of the rear console and gently wiggle, pull backward and lift upward. Pull the hand brake so it is easier to remove the loosened rear console panel. 5. Use a flat head screwdriver to pry the rectangular 'cushion' around the automatic gear shift. Gently pry at various spot and the rectangular 'cushion' will come off easily.6. Now you are just one more plastic cover away from the burned bulb. The plastic cover that has those 'P'ark, 'R'everse, 'D'rive letters is held in place by four snap on latches. Use a small flat head screwdriver and gently push the black latches inward in a downward motion, once the screwdriver head gets inside the grey latch holder it will free the black latch. Work on each of the four latches in turn.7. Wiggle the plastic cover until it is completely loosened from the four latches. Gently lift the plastic cover up. The automatic gear shift will stop the plastic from being lifted out completely. You still have enough room to work with. You will see the little burned bulb directly below those 'P'ark, 'R'everse, 'D'rive letters. Gently pull the bulb out. I got my replacement bulb at Canadian Tire, Motomaster instrument replacement bulb 194LL (clear, long lasting, 2 bulbs for $2.99Cdn). It is a push-on bulb.8. Test the bulb by starting your car and dash lights.9. Snap back the plastic 'P'ark, 'D'rive cover. Put back the rear console panel and finally the rectangular 'cushion' around the automatic gear shift.

Dec 17, 2011 | 2006 Toyota Corolla

1 Answer

I have an automatic gear shift console light bulb that needs replacement. It's a 1998 Toyota Corolla. I already removed the two side screws and two compartment bolts to get the two console pieces apart....


That is a very tough bulb to replace. Once you get the center console pieces out of the way there should be a couple of screws or blots that hold down the trim around the gear shift. Remove those and lift gentley. You will barley be able to access the bulb. but it can be done.

Feb 10, 2011 | 1998 Toyota Corolla

1 Answer

Replace bulb on automatic gear shift console


If the shift console is on floor then look for bolts holding it down.  Take out bolts and then you can maneuver console so you can see where light is plugged in and get the right light to replace it.  It will probably be a small light which tend to cost a bit more, but at least you'll have the light back.

Apr 01, 2010 | 2004 Toyota Highlander

1 Answer

Light bulb is burned out on gear shift console. How to remover cover?


The center console needs to be removed, pull the shift plate plastic cover off, remove two bolts inside the console storage box, remove the phillips screws that are visible, the front center storage box also has to be removed, the bulb is located on the left side of the shifter from underneath.

Hope helped with this (remember rated this help) Good luck.

Nov 11, 2009 | 1995 Toyota Corolla

1 Answer

Gear shift light out in 1997 Honda


remove console and inspect for sought after malfunctioning bulbs and replace and reinstall console .

Nov 30, 2008 | 1997 Honda Accord

2 Answers

Automatic Gear Shifter Light Burned Out


You shifter indicator bulb (194 bulb number) has burned out. Pretty easy and cheap fix. The top of the indicator has to be removed/lifted up and teh bulb needs to be replaced.

Oct 24, 2008 | 2001 Nissan Sentra

Not finding what you are looking for?
2011 Chevrolet HHR Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23515 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...