Question about GMC Cars & Trucks

1 Answer

Do you have to drop the engine to replace oil pump in 2007 gmc yukon

Can you get to the oil pump with out taking the engine apart

Posted by Megan on

Ad

1 Answer

Terry Hair

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 4,134 Answers

You have to remove the engine front cover (over timing chain) and remove the oil pan to get the oil pump in and out. You don't have to remove the heads, however.

Removal & Installation

4.8L, 5.3L, 6.0L & 6.2L Engines






Fig. Exploded view of the oil pump mounting-4.8L, 5.3L, 6.0L and 6.2L engines


Fig. Oil pump disassembly-4.8L, 5.3L, 6.0L and 6.2L engines



  1. Remove or disconnect the following:


    NOTE

    Do not allow dirt or debris to enter the oil pump assembly, cap ends as necessary.




    NOTE

    The internal parts of the oil pump assembly are not serviced separately (excluding the spring). If the oil pump components are worn or damaged, replace the oil pump as an assembly. Do not attempt to repair the wire mesh portion of the pump and screen assembly.





    Engine front cover Oil pan Oil pump screen bolt and nuts Oil pump screen with O-ring seal. O-ring seal from the pump screen. Discard the O-ring seal. Remaining crankshaft oil deflector nuts. Crankshaft oil deflector Oil pump bolts







    Oil pump To install:




    NOTE

    Inspect the oil pump and engine block oil gallery passages. These surfaces must be clear and free of debris or restrictions.




    1. Align the splined surfaces of the crankshaft sprocket and the oil pump drive gear and install the oil pump. Install the oil pump onto the crankshaft sprocket until the pump housing contacts the face of the engine block.


    2. Install or connect the following:


      NOTE

      Lubricate a NEW oil pump screen O-ring seal with clean engine oil.




      NOTE

      Push the oil pump screen tube completely into the oil pump prior to tightening the bolt. Do not allow the bolt to pull the tube into the pump.





      Oil pump bolts. Tighten the oil pump bolts to 18 ft. lbs. (25 Nm). Crankshaft oil deflector







      NEW O-ring seal onto the oil pump screen





    3. Align the oil pump screen mounting brackets with the correct crankshaft bearing cap studs.


    4. Install or connect the following:




      Oil pump screen Oil pump screen bolt and the deflector nuts. Tighten the bolt to 106 inch lbs. (12 Nm) and the nuts to 18 ft. lbs. (25 Nm). Oil pan Engine front cover








Posted on Mar 06, 2015

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What should the cold start oil psi and the 190 degree warm up oil psi be on a 2000 to 2002 gmc Yukon with a 5.3 eng


Different engines can show different values. Sometimes it is the sensor itself that causes the variation. The pressures that you are witnessing are well within operation norms and are nothing to be worried about. As long as you don't experience severe drops in oil pressure during acceleration and deceleration, then the oil pressure system is working well.

Mar 03, 2015 | GMC Cars & Trucks

1 Answer

2007 GMC YUKON took change spark plug, the one on the left by the firewall had oil on the spark plug thread. why was that? help me understand.


That could easily be melted grease from the engine compartment or spilled oil when filling your oil during changes or top off.

Feb 17, 2015 | 2007 GMC Yukon

1 Answer

My 02 GMC Yukon 5.3 Ltr flex fuel won't crank if the fuel is less than half a tank. Do I need a fuel pump. Carmax said that it was nothing but it was doing this since I purchased in 2007. Please help...


There is a hose from the fuel pump to the bottom of the sender unit. You can replace it, but it isn't any fun. You have to empty the fuel, drop the tank, pull the sender out, take the sender apart. Cut the flex hose off, replace it with fuel line hose only. The clamps will be hard to get on and adjusted. I have done it myself and kids. But not for anyone else. Cheaper to buy the unit.

Jan 29, 2015 | GMC Cars & Trucks

1 Answer

2007 Yukon xl denali burning oil


If you smell burning oil, you may have a leak in the engine compartment reaching the exhaust manifold and burning on contact. The most common cause for that is leaking valve cover gaskets. If you are losing oil with NO signs of external leaks, the engine may be burning it internally. Valve stem oil seals, worn piston rings, blown/leaking head gasket are a few causes of that.

Oct 07, 2012 | 2007 GMC Yukon XL Denali

1 Answer

How to change oil pump in 2004 gmc Yukon


Remove the engine oil pan then remove the screen and pump. Replace with a new screen if replacing the pump. Load the oil pump full of Vaseline so it will prime upon starting

Sep 15, 2011 | 2004 GMC Yukon

1 Answer

2007 GMC Yukon using a quart of Oil every 2000 - 3000 miles


Sounds funny, I would take it to an indepened repair shop and have them check it out, we have many customer's with Yukon and have not heard of that, I have a GMC with over 315,000 miles and between oil changes, maybe a qts low, have it check else where.

Jul 08, 2010 | 2007 GMC Yukon

1 Answer

1995 GMC YUKON I HAVE CHANGE THE OIL SENDING UNIT THE OIL GAUGE IS STILL DROPPING TO 20 PSI WHEN EITHER AT A STOP OR IDLING I HOPING THAT THE OIL PUMP NOT GOING I CANT AFFORD TO REBUILD A MOTOR THIS TIME...


you will need to put a pressure gauge right on the engine to see whats real. Do an oil service with filter. This could help, If the pressure is stll low you could put a oil pump in and hope for the best. As long as you have pressure you should be ok. 20psi at idle can be a sign of old oil so cross your fingers.

Nov 24, 2009 | 1995 GMC Yukon

2 Answers

2006 Yukon Denali, oil pressure gauge malfunction


Most likely the oil pressure sensor is bad. Its located in the very rear of engine on top of bell housing area.

Oct 30, 2009 | 2006 GMC Yukon Denali

1 Answer

Speed Odometer and Oil Gauge Drops


GMC yukons are notorious for gauge malfunctions, there are recalls for some models
However, if you have recently changed your battery this problem can occur and will take some driving time 30 min-60 min for the computer to fully reset.

Jan 20, 2009 | 2003 GMC Yukon XL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Ryan Lutton
Ryan Lutton

Level 3 Expert

1256 Answers

john h

Level 3 Expert

23515 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...