I recently bought n previous owner didnt know the code on drivers door for keyless entry. Needless to to say my car is out front running with doors locked. Purse, cell, etc locked inside. To avoid a locksmith coming out at 9pm in a foot of snow is there a way to reset it????

Hello Cathy

It does indeed have keyless entry. It needs reprogramming when you get a new remote. Also if you disconnect the battery. Usually a local car alarm fitting shop, or an auto-electrician will do it. Plus of course a Ford dealership.

https://www.google.com/search?q=Keyless+Entry+Remote+System+1999+Ford+Windstar

..

Nope, your supposed to do that before this happens.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

door pad keyless codes?

in owner manual, enter permanent code and then press "1" and enter personal code, then press "1" again. Then both codes will work.

If you don't have manual, go to Motorcraft.com and click on technical resources and click on your year owner manual.

---------------------------------------------
Each vehicle equipped with a keyless entry keypad is programmed with a five-digit entry code. This code is provided to the customer through a wallet card in the Owner Literature package. In addition, this code is available through a diagnostic tool and is also printed on the vehicle security module label. When entering codes each digit must be entered within five seconds of the previous button press.
Programming/Erasing Personal Code
A unique personal five-digit code can be programmed by following these steps:

1. Enter the factory set five-digit code (the keypad will illuminate when pressed).

1. Press 1/2 within five seconds of Step 1.

1. Enter the unique five-digit code.

The personal code does not substitute for the permanent factory set code. Either code can be used to access the vehicle. In addition, if a second personal code is programmed, it will simply overwrite the previous personal code. To erase a personal code, carry out the following procedure:

1. Enter factory set five-digit code.

1. Press 1/2 within five seconds of Step 1.

1. Press 7/8 and 9/0 at the same time within five seconds of Step 2.

The system will now only respond to the factory set code.
Anti-Scan Feature
To provide added security, the keyless entry pad is disabled for one minute after 35 button presses without a valid entry code being entered. The keypad will flash during this one-minute mode with all functionality disabled except for 7/8 and 9/0 still being allowed to lock the vehicle.
Anti-Scan will be turned off after any of the following events:

• one minute of keypad inactivity
• the keyless entry remote transmitter UNLOCK button is pressed
• the ignition is turned to the ON position.

Unlocking the Doors with the Keyless Entry Keypad System
To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will illuminate.
To unlock all doors, enter either the factory set code or the personal code (driver door unlocks) and press the 3/4 control within five seconds.
Locking the Doors with the Keyless Entry Keypad System
It is not necessary to enter the factory set or personal code prior to locking all doors. To lock all doors, press the 7/8 and 9/0 controls at the same time.
Inspection and Verification

1. Verify the customer concern by operating the system.

1. Visually inspect for obvious signs of mechanical or electrical damage.

I have the 1995-97 Lincoln Continental Alarm, Remote Starter, Keyless Entry Wiring, review it:




Hope helped.

it's in owner manual. But, first you have to enter your original code and it must work. then you press the 1 button and then enter a new 5 digit code, then press the 1 button again.

Keyless Entry Keypad To unlock the driver front door (20124) , and disarm the anti-theft alarm control (19A366) , (if equipped):

• Enter the permanent factory code.
• Enter the owner's alternate code.

To unlock the passenger door(s), press the 3/4 button within five seconds of unlocking the driver door or luggage compartment. To unlock the luggage compartment door (40110), press the 5/6 button within five seconds of unlocking driver or passenger door(s). To turn on the courtesy lamps and light all illuminated components, lift either front door handle (22404) or press any button on the keyless entry keypad (14A626) . To lock all doors, press the 7/8 and 9/0 buttons at the same time with all doors closed. (It is not necessary to enter the key code first.) This will turn off courtesy lamps and arm anti-theft alarm control (if equipped). To program an alternate code:

1. Enter the five digit permanent entry code into keyless entry keypad .

1. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code.

1. Enter any alternate five digit code within five seconds of pressing 1/2 button.
   • Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code:
     • 9/0 — no memory recall
     • 1/2 — memory seat position 1
     • 3/4 — memory seat position 2
     • 5/6 — memory seat position 3
   • After successful programming, the doors will signal by locking and then unlocking.

---------------------------------------------

• Keyless Entry Keypad Does Not Work Properly

• Circuit.
• Keyless entry keypad.
• Electronic door lock control processor.

Open Fuses:

• Town Car and Crown Victoria/Grand Marquis
• Power Distribution Box (under hood)- K, 40A (Maxi)
• Instrument Panel Fuse Panel - 17 (10A), 10 (20A), 8 (15A), 5 (15A) and 4 (10A)

Loose Connectors

Corroded Connectors

1. Enter the five digit permanent entry code into keyless entry keypad.
2. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code. (Factory code found on the module).
3. Enter any alternate five digit code within five seconds of pressing 1/2 button.
   • Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code: 9/0-- no memory recall
     1/2-- memory seat position 1
     314-- memory seat position 2
     5/6-- memory seat position 3
     
   • After successful programming, the doors will signal by locking and then unlocking.
   
   

The Keyless Entry Module is located inside the drivers side door.

Open the trunk and up under the package tray where rear speakers mount,on the passenger side you will see the module.It will be black and have 3 connectors to it.It will have a sticker on it with a 5 digit code.It will also have a sticker on one of the trunk hindges with this code if someone has not removed it.Here is how the system works:

Keyless Entry Keypad To unlock the driver front door (20124), and disarm the anti-theft alarm control (19A366) (if equipped):

• Enter the permanent factory code.
• Enter the owner's alternate code.

To unlock the passenger door(s), press the 3/4 button within five seconds of unlocking the driver front door or luggage compartment door (40110) . To unlock the luggage compartment door, press the 5/6 button within five seconds of unlocking the driver or passenger door(s). To turn on the interior lamps (13776) and light all illuminated components, lift either front door handle (22404) and press any button on the keyless entry keypad (14A626) . To lock all doors, press the 7/8 and 9/0 buttons at the same time. (It is not necessary to enter the key code first.) This will turn off courtesy lamps. To program a temporary code:

• Enter permanent code.
• Within five seconds of pressing last button of permanent code, press 1/2 button.
• Enter any alternate five-digit code within five seconds of pressing 1/2 button.

Yes you can program your own code by inputting the original code then hit the no. 2 button then input your own 5 digit code.

If you are refering to the Keyless entry code it may be on a white wallet card in the owners manual package. If your truck was bought used it may be with the previous owner.

Contact the dealer. You will have to verify ownership.