Question about 2006 Hyundai Accent

1 Answer

Why is my Hyundai Accent 2006 cvvt battling to idle after cambelt broke. Was replaced with valves ect. Currently driving without airflow sencor being plugged in. Wouldn`t idle with it plugged in?

Compression test was done - 100 percent. Three of the 4 pencil coils have been replaced. Car was at Hyundai on computer couldn`t find anything. This problem is ongoing for almost 3 months. Please help!

Posted by Hannelie Goosen on

  • Bill Boyd Mar 04, 2015

    have the camshaft timing rechecked. If there are no fault codes then the problem has to be mechanical. valve timing, hydraulic followers etc. It is strange that thee is no code for the MAF/VAFnot plugged in



1 Answer

Bill Boyd

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Hyundai Master
  • 53,812 Answers

I would suggest a compression test to ensure that all the damaged valves were replaced. Replace the MAF sensor as it appears that it is faulty

Posted on Mar 04, 2015

  • Hannelie Goosen
    Hannelie Goosen Mar 04, 2015

    The compression test was done and was 100 percent



Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replaced a timing belt that broke while driving.

check compression on each cylinder, if u have zero clearance on those valves u may need to replace the head or have a valve job

Oct 02, 2014 | 2003 Hyundai Accent

2 Answers

The timing belt broke in my daughtrs 2006 hyundai accent. How or can i tell if i need new valves and or rods it doeshave a knck in it now and wnt stay idling very long when i start it

if you have damaged rods or valves in your engine, there would be almost no chance that the engine would run or even start. it is quite possible that you did not get your timing right when changing the belt. in most cases, getting the pulley to piston 1 TDC does not always guarantee that the engine timing is correct.
my advice is to recheck the timing of the engine, as well as Ignition timing (which is also controlled by the positioning of the crank pulley) before condemning any internal mechanical failure.
to answer your question, there is no written way of knowing whether your rods or valves are damaged without taking apart the engine and inspecting for damage. however, damaged internal components will always leave a trail.
you can try draining the engine oil and checking the oil for any metal filings. you can also take out the oil sump to check for any pieces of broken metal in the sump.
hope that helps

Aug 27, 2014 | 2006 Hyundai Accent

1 Answer

2002 hyundai accent wont rev passed 2500 rpm,

Have the fault codes read Replace the faulty units with genuine one because most aftermarket units are not set
for OEM cpu units and are not completely compatible

May 05, 2013 | 2002 Hyundai Accent

1 Answer

1999 hyundai accent gl bogs down when i put in gear just replaced coil pack sparkplugs and wires any ideas

Without actually looking at the vehicle, it's difficult to say. The 1999 accent was equipped with an idle speed conrol actuator (common issue) or there may be a vacuum leak at the surge tank or the problem may be something electrical. Without a proper inspection/diagnosis of engine management components, it could be anyone's guess. Valve timing could be 'out', poor cylinder compression, restricted intake air flow, poor quality fuel/gasoline, restriction in the exhaust system, low fuel pressure, and the list goes on and on.

Best advice. Have a qualified Hyundai Service Technician properly diagnose your vehicle.

Aug 26, 2011 | 1999 Hyundai Accent

1 Answer

2007 Accent, code P0012, checked CVVT valve OK, wiring to and from PCM OK. Found cvvt oil filter dirty, replaced did not solve problem. I'm thinking the CVVT control gear is bad.

The main thing to check is to verify the operation of the VCT solenoid. You're looking for a sticking or stuck VCt solenoid valve caused by contamination. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.

Aug 12, 2011 | 2007 Hyundai Accent GS Hatchback

1 Answer

Hyundai accent 2001. The cambelt needs replacing, I have a mechanic, but need the workshop manual for assistance and you can't seem to buy these anymore. Where can I find information on changing the...

i would go to a different mechanic. cambelt is an easy job and he shouldnt need a manual.

you should be able to buy a manual on ebay or your local autoparts shop should be able to order one in

Sep 18, 2010 | 2001 Hyundai Accent

2 Answers

Jaguar xj6 4.0 1990. showing fault code fuel 14, fail 14. what does this code mean ?

2 airflow sensor out of operating range 3 coolant temp sensor out of operating range 4 oxy sensor indicates full rich 5 throttle potentiometer/airflow sensor... (low throttle pot signal with high airflow sensor signal) 6 throttle pot/airflow sensor...... (high throttle pot signal with low airflow sensor signal) 7 throttle pot...idle fuel adjustment failure(idle speed??) 8 intake air temp or shorted circuit to sensor 11 Throttle pot at idle: Throttle pot idle trim out of normal range 12 Airflow meter: MAF signal out of range 14 Coolant thermistor: Resistance out of range or static during engine warm up 16 Air thermistor: Resistance out of range 17 Throttle pot: Out of range 18 Throttle pot/Airflow: Low throttle pot signal at high airflow 19 Throttle pot/Airflow: High throttle pot signal at low airflow 22 Fuel pump drive: ECU output to fuel pump relay 23 Fuel supply: Engine running too rich 24 Ignition Drive: ECU output to ignition Amp 26 Air leak: Engine running too lean 29 ECU self check 33 Injector Drive: ECU output to injectors 34 Injector: Looks for Injector dribble 37 EGR Drive: ECU output to EGR switching valve 39 EGR check sensor: EGR not working (normally pipe blocked) 44 Lambda (O2) sensor: Poor mixture control rich or weak (or misfire) 46 Idle speed Control valve: ECU output to Coil AB 47 Idle speed Control valve: ECU output to Coil CD 48 Idle Speed Control Valve: Stepper motor grossly out of position 66 Air pump: ECU output to air pump relay 68 Road speed sensor: Seen speed < 5km/h at high engine airflow 69 Drive/Neutral switch: Seen cranking in "D" or high airflow in "N" 89 Purge Valve drive: ECU output to purge valve
this is all I could find

Nov 09, 2009 | 1990 Jaguar XJ6

1 Answer

My 2006 Accent is idling high

the tps (throttle position sensor) could be causing the problem

Oct 03, 2008 | 2006 Hyundai Accent

Not finding what you are looking for?
2006 Hyundai Accent Logo

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides