Question about Mitsubishi Cars & Trucks

1 Answer

I have 1998 mitsubishi mirage i have just changed ecu /ignition assy with key reader and ignition module but the ecu is out of a different car to the ignition and module.will i need to code or synch ecu to igniltion ??

Posted by Corie Wright on

Ad

1 Answer

Randy Ohler

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 14,585 Answers

Yes. problem is that some years won't sync with others. You should have gotten everything out of the same car. Then you wouldn't have to do anything except start and drive your car. you did get everything you needed, just got them out of two different cars. Codes won't match. 1 in 1000 chance they will match codes. I do this all the time, but you have to gt everything out of one car. ECM, BCM, Key,Ignition chip, and some times the instrument panel. And there is year specific, because of transmissions. But I can fix that problem also.

Posted on Mar 03, 2015

  • Corie Wright
    Corie Wright Mar 03, 2015

    ok i thaught mite be the case but was hoping fir a proceedure to re sync them.

×

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: How to reset ecu unit

I dont know about the mirage but 9 out of 10 cars all you have to do is unplug your battery for at least 5-15 minutes and then re plug in and start car. your check engine light/ecu should be reset now. Good Luck and God Bless. Hope this helps. Take care. 16

Posted on Nov 20, 2008

Ad

Anonymous

  • 64 Answers

SOURCE: I need a radio unlock code.

you have to call Mitsubishi and give them the serial # and model # on the radio . they will look it up in the computer ans give you the code

Posted on Dec 01, 2008

tripletauto

TripleTauto

  • 1450 Answers

SOURCE: WHERE IS THE ECU IN 1994 LINCOLN TOWN CAR

it is in firewall on left side close to master cylinder

Posted on Dec 12, 2008

Anonymous

  • 56 Answers

SOURCE: Cannot locate the computer module (ECU) in the 1998 Sonata

lower right passenger side behind the kick panel just lower than the glove box location.
on some early models it was located in the center console forward section.
see this link---
http://www.mirage-performance.com/sonata/Wiring/

Ps. dont forget to rate my answer please... Thanks

Posted on Dec 27, 2008

Anonymous

  • 37 Answers

SOURCE: Mitsubishi Galant 1995 ignition problem

its probably ign swich - located on end of ignition cylinder - round with 5 maybe 6 male terminals harness plugs into

Posted on Jan 11, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 1998 mirage i recently replaced ecu ignition and imobilizer module it now runs but sounds louder than before it seems like a deeper note at air box and just dont seem the same could it be ignition...


This could be different programming of the new ECU. You might also need to get it tuned with the new ECU. It could have changed the ignition timing.

Mar 10, 2015 | 1998 Mitsubishi Mirage

1 Answer

I have a 98 Mitsubishi Mirage. THe key is stuck in the ignition. I can crank the car, just can remove the key and the steering wheel will not "lock" when it is turned. Is there an easy way to...


Has this car even been in an accident where the airbags deployed? I had this occur on my Chrysler after an accident, so it may be a feature to insure that you get it repaired properly. In my case the car was totaled, so no repair was made.

May 29, 2011 | 1998 Mitsubishi Mirage

1 Answer

I have a 95 Mitsubishi mirage. The check engine light keeps coming on and when I hook up the code reader it tells me that the code po340 which is the camshaft position sensor. My book says its in the...


I would check your wires make sure, its more common than not, but it could also be the engine control module as well. and unless the distributor was new could also be a bad module inside the distributor.

Jul 26, 2010 | 1995 Mitsubishi Mirage

2 Answers

Lost key to a 2000 Mitsubishi Mirage


call a lock smith he can make a new key with out haveing to change the locks nor the ignicion switch

Jul 11, 2009 | 2000 Mitsubishi Mirage

1 Answer

Part number needed - Mitsubishi Mirage 1998, 1290cc


the mitsubishi dealership should be able to help you on that

gl G

Apr 24, 2009 | 1998 Mitsubishi Mirage

1 Answer

Where is the ignition timing adjustment connector?


On this car the ignition timing is controled by Engine Control Module (ECM) and is not adjustable. However it can be inspeced using a scan tool.

Mar 14, 2009 | 1997 Mitsubishi Mirage

1 Answer

Cannot locate the computer module (ECU) in the 1998 Sonata


lower right passenger side behind the kick panel just lower than the glove box location.
on some early models it was located in the center console forward section.
see this link---
http://www.mirage-performance.com/sonata/Wiring/

Ps. dont forget to rate my answer please... Thanks

Dec 27, 2008 | Hyundai Motor 1998 Sonata

2 Answers

How to reset ecu unit for a 1990 mitsubishi mirage


I dont know about the mirage but 9 out of 10 cars all you have to do is unplug your battery for at least 5-15 minutes and then re plug in and start car. your check engine light/ecu should be reset now. Good Luck and God Bless. Hope this helps. Take care. 16

Sep 02, 2008 | 1991 Mitsubishi Mirage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Vincent G
Vincent G

Level 3 Expert

2363 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...