Question about Cars & Trucks

1 Answer

How do i reset codes on my hyundia accent. Just replaced the fuel pump and camshaft position senser and the problem still exists

Posted by Robert Pelland on

Ad

1 Answer

Stephen

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 21,873 Answers

After the problem is repaired, the codes would be erased with a code reader or scanner.

Posted on Feb 27, 2015

Ad

5 Related Answers

Anonymous

  • 55 Answers

SOURCE: replacing bad camshaft position sensor

  1. Disconnect battery ground cable.
  2. Remove water pump pulley attaching bolts, then the serpentine belt and water pump pulley.
  3. Disconnect sensor wiring connector and remove sensor retaining bolt.
  4. Twist and pull sensor to remove.
Reverse procedure to install and prior to installing new sensor, lubricate sensor O-ring.

It is located under the water pump. Make sure when you remove the sensor that you rotate the crank shaft and look in the hole to make sure the pick up magnet is still in there. Sometimes they come loose and cause a no start or long crank. You will need to have the code cleared still.

Posted on May 06, 2009

Ad
ourhowse

Dar

  • 2007 Answers

SOURCE: 92 dodge 318 truck engine runs til you stop, then stalls when put

Then i think i'd be dumping some soapy water on the intake gaskets checking for leaks. ANd wiggle the **** out of all vacuum hoses. ( you probably did that) And if there aren't any, your cam could be tired. You got a tough one there. Hard to figure with a keyboard.

Posted on May 17, 2009

csmock132

Clint Smock

  • 4669 Answers

SOURCE: ERROR CODE 0340 AFTER TIMING BELT REPLACEMENT

Well either coincidence that the cam sensor went bad, you forgot to plug in the cam sensor, Or you have the cam that the sensor reads off of 1 tooth off. Check to see if its plugged in if yes remove the upper timing cover and see if everything lines up.

Posted on Jun 08, 2009

ghost4548

Paul McGrath

  • 776 Answers

SOURCE: 2005 HYUNDAI ACCENT ERROR CODE 0340 AFTER TIMING BELT REPLACEMENT

Here's what the shop manual says.

ef0163d.jpg
7a00d7b.jpg

Posted on Jun 28, 2009

Anonymous

  • 113 Answers

SOURCE: OBD gave code for camshaft position sensor-how to replace?

haynes should have a manual on this car, which will show the location of the cam pos sensor. check autozone or napa

Posted on Jul 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Tryingn to find fuel pump shut off for a 2005 hyundia accent


pull the relay-- their is no fuel cutoff--fuel reset -or inertia switch on vehicle

Aug 02, 2016 | 2005 Hyundai Accent

1 Answer

How do i get 06. Hyundia accent to relearn idle after replacing camshaft position senser


Clear codes w/scan tool and drive the car. Will relearn after so any miles of driving. If you don't have scan tool, can try disconnecting battery. Car should figure out sensor is fixed after 3 different successful trips and turn off CEL on it's own.

Feb 27, 2015 | Cars & Trucks

1 Answer

Where is the fuel filter located on a 2001 hyundia accent?


On top of the fuel tank beside the fuel pump. Accessible by removing the rear seat and detaching the inspection panel of the fuel pump.

Aug 08, 2011 | 2001 Hyundai Accent

1 Answer

My fuel pump went out and i replaced it but i cant find the reset button its for 2001 hyundia accent 1.5 liter can u help me?


There is no fuel pump reset button, you need to get the manual and locate either the relay or the fuse. The only other issue would be that you have not installed or connected the power wires to the fuel pump correctly. Hope this helps

May 29, 2011 | Hyundai Accent Cars & Trucks

1 Answer

Looking at a 2000 hyundia accent but has a check engine light code of po447 is this a big problem


Research revealed no data availabe for code P0447 - doesn't exist for Hyundai Accent.

There are codes P0446 and P0445, but nothing with P0447.

Feb 06, 2011 | Hyundai Motor 1998 Accent

3 Answers

My 2005 hyundia accent has spark but no power to fuel pump or injectors


With the key on,the fuel pump is only activated for 1 second,the off,until the vehicle is turned over again,then it will come on again,checking power to the fuel pump,is not easy to do,,I am thinking maybe the fuel pump is coming on,but the injectors are not pulsating,replace the crankshaft sensor ,it controls spark,and injector pulse.

Feb 13, 2010 | 2000 Hyundai Accent

2 Answers

I have Hyundia accent 2001 with the code po335 what i need to do.


That is the code for faulty connection to, or bad Crankshaft position sensor. Not 100% sure of exact location but should be near flywheel, or at front near crankshaft.

Feb 02, 2010 | 2001 Hyundai Accent

1 Answer

2006 hyundia accent check engine light is flashing


big red
if you have not had problems with your car the most probable thing is you need to replace your maf sensor you can also jut remove it and cleane it with alcohol then reset your cars computer by removing the positive cable from your car for about 2 minutes and placing it back it will clear the engine code

Oct 23, 2009 | 2006 Hyundai Accent

3 Answers

2001 Accent, suddenly won't start


your model doesn't use an Inertia cut off switch for the fuel pump, chances are the fuel pump has just failed, they do that quite often.

Sep 04, 2009 | 2001 Hyundai Accent

1 Answer

Ok, used a code reader...


Here is a list (courtesy of www.obd-codes.com).
Symptoms Symptoms can include:
  • Hard starting or no start
  • Rough running / misfiring
  • Loss of engine power
Causes A code P0340 could mean one or more of the following has happened:
  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed
Possible Solutions With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required
Best of luck.
Greg
p.s. the code can be reset but if a problem exists, it will return

Jul 03, 2009 | 2002 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

23424 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...