Cars & Trucks Logo

Related Topics:

QUNDELL ATKINS Posted on Feb 20, 2015

What happens when gmc envoy does not pick up speed 2008

  • jklisiewicz Feb 20, 2015

    Hi QUNDELL ATKINS, I want to help you with your question, but I need more information from you. Can you please add details like what engine your envoy has in it, and when the condition happens? Is it only when its hot or cold or all the time? Is it under hard, light, or normal acceleration? Does it maybe seem to only happen on the highway or up hills? Has any work been done to the truck recently that may have caused this condition? Please post a reply in the comment box.

×

3 Related Answers

ryanlutton

Ryan Lutton

  • 1267 Answers
  • Posted on Feb 09, 2011

SOURCE: I have a 2004 GMC

Clean your throttle body for starters. When this is filthy, and it will be filthy, the throttle body will learn some bad habits. So the engine will go into a safe mode "reduced power". Clean the TB with TB cleaner with the battery disconnected, must be nice and shiny front and back. When finished, connect the battery back up and drive around for 20 minutes or so with all accessories off. This way the computer will re-learn a newly cleaned, properly functioning throtte body. This seams to be the main culprit with this problem. Hope this helps!

Ad
redds55

Ricky Peters

  • 2620 Answers
  • Posted on Jun 25, 2012

SOURCE: How do I tune up my 2008 GMC Envoy

Go to www.autozone.com an sign up then click on repair info.

Christopher Davis

  • 48 Answers
  • Posted on Nov 23, 2013

SOURCE: 2006 GMC Envoy car alarm goes off when I open doors or start engine. This happened after installing new battery. It had the same problem when I bought it in 2008. I forget how it was solved.

U need to reset security system (pass lock II). Turn key to on right b4 cranking but don't start and let security light flash for about 10-12 mins until it stops and then turn key back off, repeat procedure two more times don't actually turn key far enough to start during first two 10-12 min cycles, third cycle though after flashing stops turn the rest of the way forward for it to start. This should then reset security and solve problem sometimes only takes two cycles to reset. Good luck, hope this is helpful & solves problem.

Testimonial: "Thanks for you input but it didn't work. Any other suggestions?"

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2008 GMC Envoy 4.2. My back hatch won't lock!!!

Question edited for clarity and toss in some CAPS.
Question moved to model category.

Help in the link. Basically something in the linkage was come apart. The noise is the electronic solenoid. It is the same for all models, you just have to get in there.

https://www.google.com/search?q=2008+GMC+Envoy+hatch+won%27t+lock

..
0helpful
1answer

2008 GMC Envoy

this sounds like is a lost joint in the engine or a broken gear box
1helpful
1answer

Does the generator battery control module on a 2008 GMC Envoy require programming?

Yes, the generator battery control module on a 2008 GMC Envoy requires programming.
0helpful
1answer

Wont pick up speed

in limp mode check for codes

If you need further help, I’m available over the phone at https://www.6ya.com/expert/mike_9693b5ad75773352

0helpful
1answer

How do I tune up my 2008 GMC Envoy

Go to www.autozone.com an sign up then click on repair info.
0helpful
1answer

2008 GMC Denali, Fusebox location

It would be helpful if we knew if you were talking about a 2008 Envoy or a 2008 Denali, since your post says both. In either case, the subject of fuse locations is covered in the Owner's Manual....
0helpful
1answer

I have a 2004 GMC Envoy, while I,m driving the reduce engine power light comes on then it dies! This happens 10 to 12 times a day. It will sometimes do it if I change the heat from high to low or the...

Clean your throttle body for starters. When this is filthy, and it will be filthy, the throttle body will learn some bad habits. So the engine will go into a safe mode "reduced power". Clean the TB with TB cleaner with the battery disconnected, must be nice and shiny front and back. When finished, connect the battery back up and drive around for 20 minutes or so with all accessories off. This way the computer will re-learn a newly cleaned, properly functioning throtte body. This seams to be the main culprit with this problem. Hope this helps!
4helpful
2answers

The blower speed switch only works on 5. The

this problem is caused by a defective blower speed control resistor, it is located near the blower motor, very cheap to replace, part is around $35
Not finding what you are looking for?

29 views

Ask a Question

Usually answered in minutes!

Top GMC Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

john h

Level 3 Expert

29492 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...