Question about 1999 Chrysler Concorde

1 Answer

I got a car 1999 concord chrysler 2,7 with a engine code 1391

Posted by Anonymous on

Ad

1 Answer

carlos falero

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Chrysler Master
  • 1,327 Answers

For that code you need to take the car to expert

Posted on Feb 17, 2015

Ad

5 Related Answers

Zachary Kloefkorn

  • 156 Answers

SOURCE: 2001 chrysler concorde engine codes

P0455 Evaporative Emission Control System Leak Detected (gross leak) - check your entire engine bay contents for any type of leak, air conditioner when it's running, coolant, things like that.

P1684 Battery Disconnected Within Last 50 Starts - this is a code that will go away over time

Posted on Mar 25, 2009

Ad

Dan C

  • 93 Answers

SOURCE: Location of engine oil drain plug on 1999 Chrysler Concorde - 3.2L engine

It isn't immediately obvious to find, as the head is smaller than you probably are used to. Make sure you aren't looking at the wrong pan. It's not so hard to get turned around when you're upside down and think you are looking at the engine pan when you are looking at the trans pan.
Take another look and you'll find it.

Posted on Apr 16, 2009

chryslerguy

  • 323 Answers

SOURCE: Chrysler Concorde LXI 4 door - 2004 The car starts up and seconds after, the RPM drops and the car shuts off. The code P0513 comes up on the computer.

That is a code for an invalid skim key. If you have another skim key try it. If it does the same thing then the skim module may be bad.

Posted on May 07, 2009

Anonymous

  • 1392 Answers

SOURCE: I have a 2000 chrysler concorde that the engine light just popped on - the error codes are po302, po420, po340

P0302-cylinder #2 misfire detected
P0420- catalyst efficiency below threshold bank 1
P0340-No cam signal at PCM.
The Cam sensor most likely needs to be replaced first. Clear the codes after that and drive and see what comes back on.

Posted on May 29, 2009

Anonymous

  • 124 Answers

SOURCE: I have a 1999 jeep grand Cherokee larado V6.

The P1391 code indicates that the crank or cam sensor(s) have sent an intermitant code to the ecm. The most common cause for this is loose wiring or debris on the contacts of one of the sensors.

Posted on Nov 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anyone know where the alternator is located in a 1999 Chrysler Concorde, 2.7


This may not be helpful, as I have not done one on that car

I see all sorts of info on the internet

You know that it is driven by one belt,
& while you may not see it,it is on the front
of the motor & according to what I read,
seeing it isn't the problem

Moving the radiator shroud,fender covers,etc
& clearance to remove a bolt or two may be

Mar 09, 2013 | 2000 Chrysler Concorde

1 Answer

1998 chrysler concorde code P1684 P0122


P01684 just says that the battery has been disconnected within the past 50 starts. If you have already replaced the TPS and still get the P0122 code, it could be a short in the wiring or a problem with your Powertrain Control Module. Other names for the PCM is ECM and ECU. Engine Control Module and Engine Control Unit

Mar 02, 2013 | 1999 Chrysler Concorde

1 Answer

What does engine code 306 for a 1996 Concorde mean


have to take to dealer its a security code for the anti theft system i think because all other codes are four digit letter codes on 99 models.

Aug 02, 2012 | Chrysler Cars & Trucks

1 Answer

I HAVE A 1999 CHRYSLER CONCORDE LXI, CHECK ENGINE LIGHT COMES ON AND RPM RACE TO 4000 WHEN DRIVING 55MPH?


First thing is to have the computer scanned for trouble codes.
My guess would be a torque converter or overdrive problem.

Jun 26, 2012 | 1999 Chrysler Concorde

1 Answer

My engine light is on, 1999 chrysler concord. what could be the problem.


The check engine light (yellow light) comes only when the computer control unit (called the PCM) senses a fault in the electronic controls of the engine and/or the emission system u will seldom feel the car engine run any different, there are about 200 possible faults that turn the light on, to know what has developed a problem you must have the system tested, this is called an OBD2 fault code test, Kragen and Autozone parts stores do this testing for free.

Jul 02, 2010 | 1999 Chrysler Concorde

1 Answer

Hello ! my 1999 chrysler concorde shows (check


You need to have the codes read to determine what is wrong. Bring it to a parts store, this is a free service. They will plug a hand held scan tool into the cars diagnostic port (under the dash), and 'read' codes stored on the cars computer. They can tell you what the code(s) mean, and suggest how to fix the problem. If you have any questions after that, post the codes and questions (and engine size) here.

Aug 09, 2009 | Chrysler Concorde Cars & Trucks

1 Answer

I have a 2000 chrysler concorde that the engine light just popped on - the error codes are po302, po420, po340


P0302-cylinder #2 misfire detected
P0420- catalyst efficiency below threshold bank 1
P0340-No cam signal at PCM.
The Cam sensor most likely needs to be replaced first. Clear the codes after that and drive and see what comes back on.

May 29, 2009 | 2000 Chrysler Concorde

Not finding what you are looking for?
1999 Chrysler Concorde Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...