Question about 2002 Chevrolet TrailBlazer

I have a 2002 Chevy Trailblazer. The tail light does not work een after replacing bulb. I called dealership and the recalled tail light was already fixed. They said that it wasn't a fuse because the brake light and turn signal still work. Does any one have any ideas on what may be the problem?

2 Answers

Anonymous

Level 1:

An expert who has achieved level 1.
Contributor
1 Answer

I had to go back twice to get the taillight fixed from the recall, just go back and tell them it went out again, they will fix it for free.

Posted on Jul 17, 2009

honeymokey

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

President:

An expert whose answer got voted for 500 times.
Master
3,113 Answers

Replace the tail light circuit board. They are sold at most auto parts stores.

Posted on Jul 08, 2009

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

Where is the tail light fuse?

The tail light fuse is under the rear seat on the drivers side.

Jan 17, 2016 | 2003 GMC Envoy

1 Answer

Tail light and the tag light will not work

Sounds like a problem in the wiring harness.

Jan 10, 2013 | 2002 Chevrolet TrailBlazer

2 Answers

2002 chey trail blazer, my break lights will not turn on. I repalced my brake bulbs and brake stwich and they still don't work. only the middle brake light works...

did you check the VEH STOP fuse? #34, 15 amps, in the rear fuse block, under the left rear seat.

Nov 30, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

2004 Chevy Trailblazer Brake Light

I would start by trying another bulb. Even though the brake and tail light share the same bulb they actually are powering different filaments inside of the bulb so you can have a tail light filament that is working fine and illuminating properly but have a burned out brake light element that won't work at all...all inside the same bulb. Not uncommon at all to see this problem and these bulbs are pretty inexpensive.

Jul 26, 2010 | 2004 Chevrolet TrailBlazer

2 Answers

The lowbeams in my 2002 chevy trailblazer doesn't work and it is not the fuses or the bulbs

Check your relay and switch.

May 25, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

I have a 2002 Chevy trailblazer and my reverse lights will not work.Bulbs are good and no blown fuses and light under hood does not work and it has a good bulb.

you probably have a problem with your transmission range witch

Nov 01, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

Brake lights on tail don't work, upper one does.

There is a recall on the tail lights from GM. The problem I found on mine were faulty contacts that would burn out the bulb contacts in short order after replacing the bulbs. So even if you replace the bulbs they will only work for a short while before they burn out. Take it to a GM dealer to get the complete tail light assemblies replaced.

May 11, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

No brake lights

Took my Trailblazer to dealership. They replaced both rear tail light socket boards (these are plastic parts that house all of the rear lamps/bulbs and attach to tail light housing) They advised the sockets in the boards have a tendency to go bad. Everything works just fine. Cost of each part was approximately $29.00. Easy to replace yourself and save the labor.

Apr 28, 2009 | 2003 Chevrolet Trailblazer Ext

4 Answers

Replacing license plate lights on Chevy Trailblazer

I just had the same problem. I took the cover off, saw the white bulb base, twisted it to take it out, but it popped back inside the door. I got it out, but it wouldn't pull through, so I twisted it back in place and went to Autozone to get new bulb. Once I saw the new bulb, it was obvious, just the bulb itself pulls out. There's so little room to work, I couldn't get it with just my fingers - - maybe rubber gloves would have worked, but I used pliers, lightly, wiggled it a little and it popped right out. I had a similar issue once with the taillight bulb and had to break the bulb and then grip the remaining filament wires with pliers to get it out, so that was my backup plan, just in case.

Hope this helps others.

Apr 14, 2009 | 2002 Chevrolet TrailBlazer

1 Answer