How do I clear :OCER code?

Code 82 is change oil soon. If you have just changed the oil or go have it changed somewhere then you can clear it, but DO NOT simply clear it WITHOUT changing your oil and filter! Never neglect regular oil changes. $20 isn't going to break the bank. It will go a long way to ensure your engine will operate for as many years as possible. To clear the change oil code turn your car on, but leave it in park. Push the menu button until you see oil life in your DIC. Push and hold the reset button.

If the batt was disconnected the radio probably needs a pass code to reset it. Do you have it? If not go online to sites that sell pass codes for radio's. Find your make/model/serial number and see if anyone carries the code.

disconnect the battery and let it sit for about 30 minutes then reconnect. that should clear the codes. or get an ODBII code reader (about $40 ) and push the clear button. that's the easiest and you can read the codes too.

You have a generic code reader
everyone needs one

You can not how ever get MFG Codes
only those starting with PO

You should have instructions with it
You usually only have 2 buttons

One button cycles thru data & the
other clears or resets the MIL Lamps

Turn key on & write down any codes,
as you push the left button ,I believe
to cycle thru them

Then start engine & see if they are still there
& the same

Then use the other button to clear them
& road test,to see what comes back

The manual won't help much

Give me the codes or look on the
internet. Just put OBD2 & the code #
in search engine.

To clear the A047 code:

1. Re-enter diagnostics until you see PCM?

2. Keep pushing and releasing the LO button until you see ACP?

3. Push and release the HI button and you will see ACP DATA?

4. Keep pushing and releasing the LO button until you see ACP CLEAR CODES?

5. Push and release the HI button and you will see ACP CODES CLEAR.

6. Wait 3 seconds and turn the ignition OFF.

Purchase or find someone with an OBD-II Scanner that can clear and read codes on 1996 and up automobiles. They can push the 'clear codes' button to accomplish tis task of resetting the check engine light.

Good luck.

To check the computer for CODES:
1. Ignition switch ON. Engine OFF
2. Simultaneously push and hold the OFF and WARMER buttons on the climate control panel for 3 seconds and release them
3. See if you get codes such as AC1347 or AC1348 or some other LETTER/NUMBER combination display on the fuel data display along with HISTORY or CURRENT with each code or codes that display...
- AC1312 = AC high side temp sensor has an open circuit.
- AC1314 = Evaporator inlet temp sensor has an open circuit.
- AC1348 = Very low AC refrigerant condition.

Try addind about 1/2 can of freon to the system and see if the compressor engages. If not, you will need to perform some diagnostic tests on the above codes. I can e-mail you the pictures and directives on how to fix the codes, But first you need to clear (ERASE) the codes from the computer and see which codes return as current or history codes which should display just after each code.

4. After the code or codes display you will see PCM?
5. Turn ignition OFF.

To clear the codes:
1. Re-enetr diagnostics like you did before and when you see PCM?
2. Push and release the LO button and you will see IPC?.
3. Push and release the LO button and you will see ACM?.
4. Push and release the HI button and you will see ACM CODES?
5. Push and release the LO button and you will see ACM CLEAR CODES?
6. Push and release the HI button and you will see ACM CODES CLEAR.
7. Turn OFF ignition key and wait 2 minutes and re-enter diagnostics like I told you in the previous e-mail and let me know what codes appear and if they are CURRENT or HISTORY.

Hope helped.

IPC stands for Instrument panel control, here is a typical code repair flow chart, this is for example only and has nothing to do with your car..
P083 = 24x signal high.

P107 = Instrument panel control )IPC) to computer (PCM) data problem.

P137 = Loss of Automatic braking system (ABS) to Traction control system (TCS).

What you need to do is CLEAR all these codes from the computer and see which ones return.

Perform this test.

1. Ignition key ON. Engine OFF.

2. Simultaneously push and hold the OFF and WARMER (^) buttons on your climate control panel for 3 seconds and release them.

3. Diagnostic codes such as above will appear with the word HISTORY or CURRENT for each code.

4. The codes will stop when you see PCM?

5. Push and release the HI(^) button and you will see PCM DATA?

6. Push and release the LO(v) button and you will see PCM DATA?

7. Continue to push and release the LO (v) button until you see PCM CLEAR CODES?

8. Push and release the HI(^) button until you see PCM CODES CLEAR.

9. Turn OFF the ignition and wait 3 minutes and try and start the car. If the car starts and the light comes back ON, Turn OFF the car and repeat steps 1 thru 3 and let me know what codes you get and if they are HISTORY or CURRENT.

10. When you see PCM?, Turn OFF ignition key.

11. Let me know what codes you get and if they are HISTORY or CURRENT.



---------- FOLLOW-UP ----------

QUESTION: this is what happen when it did what you told me what to do.
P047 History,P107 History,No IPC Code, P83 History,P137 History, A047 Current, No Sir Codes, T072 History,No Russ, PCM?
ANSWER: You did not follow the directives correctly . If you had, You would NOT have any HISTORY CODES.

Try it again and follow these directives EXACTLY:

1. Ignition key ON. Engine OFF.

2. Simultaneously push and hold the OFF and WARMER (^) buttons on your climate control panel for 3 seconds and release them.

3. Diagnostic codes such as above will appear with the word HISTORY or CURRENT for each code.

4. The codes will stop when you see PCM?

5. Push and release the HI(^) button and you will see PCM DATA?

6. Push and release the LO(v) button and you will see PCM DATA?

7. Continue to push and release the LO (v) button until you see PCM CLEAR CODES?

8. Push and release the HI(^) button until you see PCM CODES CLEAR. WAIT 3 seconds and then proceed to 9.

9. Turn OFF the ignition and wait 3 minutes and try and start the car. If the car starts and the light comes back ON, Turn OFF the car and repeat steps 1 thru 3 and let me know what codes you get and if they are HISTORY or CURRENT.

10. When you see PCM?, Turn OFF ignition key.

Sound like you have a bad cv "constant velocity joint " REPLACE.

The first thing you need to do is to clear your old codes then drive

and see if they come back .

1. Re-enter back into the climate control panel and after all the codes display the display will stop at PCM?

2. Push and release the FAN UP (^) button on the climate control panel and you will see PCM DATA?

3. Keep pushing and releasing the FAN DOWN (v) button until you see PCM CLEAR CODES?

4. Push and release the FAN UP (^) button and you will see PCM CODES CLEAR?

5. Wait 5 seconds and then keep pushing the OFF button until you see PCM?

6. Push and release the FAN DOWN (v) button and you will see IPC?

7. Push and release the FAN UP (^) button on the climate control panel and you will see IPC DATA?

8. Keep pushing and releasing the FAN DOWN (v) button until you see IPC CLEAR CODES?

9. Push and release the FAN UP (^) button and you will see IPC CODES CLEAR?

10. Wait 5 seconds and then keep pushing the OFF button until you see PCM?

11. keep Pushing and releasing the FAN DOWN (v) button and you will see ACP?

12. Push and release the FAN UP (^) button on the climate control panel and you will see ACP DATA?

13. Keep pushing and releasing the FAN DOWN (v) button until you see ACP CLEAR CODES?

14.Push and release the FAN UP (^) button and you will see ACP CODES CLEAR?

15. Wait 5 seconds and then keep pushing the OFF button until you see PCM?

16. keep Pushing and releasing the FAN DOWN (v) button and you will see SIR?

17. Push and release the FAN UP (^) button on the climate control panel and you will see SIR DATA?

18. Keep pushing and releasing the FAN DOWN (v) button until you see SIR CLEAR CODES?

19. Push and release the FAN UP (^) button and you will see SIR CODES CLEAR?

20. Wait 5 seconds and then keep pushing the OFF button until you see PCM?


21. Push the AUTO button to get out of diagnostics.

22. Turn ignition OFF for 15 seconds.

23. Re-enter diagnostics and see if any history codes re-appear.

try you cek again cable instalasi. cex ground cable for radio or cd in light of and in light on,(in condision LIGHT OF>NEGATIP CABLE IS NEGATIP)(in condision LIGHT ON>NEGATIP CABLE IS POSITIP)soory my english so ugly bcause i indonesia(i hope that help your trouble)