Question about 1995 Audi S6

1 Answer

I've got a micro bus with a 1800 jetta mark 2 motor convertion .My problem is that i do not get any spark to my distibutor .When i start my micro bus all it does is swing but does not start .I've put in a new coil and new modulater (tp900b).I've got power on my coil and my modulater works because i had it plugged into a other micro bus .Is there any advise on how to get the spark at the distributor because it started before.

Posted by thabit_bassa on

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 295 Answers

Um u would have to change the ECU. if the tone wheels for the cam or crank pulse width are not programmed to the PCM it will not deliver spark. See if you can get what is called a PCM intersepter and have a tune shop program it for u. It seem more like a software problem.

Posted on Jul 07, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 vw jetta starts hard runs rough could it be plugged Cadillac converter or cracked coil


Not the converters. But check them to see if there is nothing in them. I've seen the converters blow apart and clog the muffler. Have the codes read.

Feb 15, 2015 | 2003 Volkswagen Jetta TDI

1 Answer

My micro bus has no spark it is a 2-6


Immobilizer disable injector not spark,may sure the battery is sufficient to turn the car over,

Mar 14, 2012 | 2005 Volkswagen Microbus

1 Answer

Where is the distibutor cap on a 1993 Jetta Wagon?


Hi, look on the engine block for the place where all the spark plug wires go, and you've find the distributor. Unsnap all clips and take off the distributor cap and suppressor shield, leaving the spark plug wires attached.

May 16, 2011 | Volkswagen Jetta Cars & Trucks

1 Answer

Have taken distibutor out of engine how do I retime engine


The easy way to find Top Dead Center is to take out # 1 spark plug and put your finger in the hole in the block. Get someone to crank the engine over as slow as you can until you feel air pressure blow by your finger. turn engine by hand until timing marks line up with 0 mark on harmonic dampener. you are now ready to install distibutor . make sure the rotor points to #1 cylinder when fully seated. It is also a good idea to line up the oil pump shaft slot with distibutor grove and it will drop in easier. Good Luck.

Jan 04, 2011 | 1980 Chevrolet Corvette

1 Answer

I have a 2006 Jetta 2.5 AT 5 cyl. I recently had the Exhaust system malfunction light come on the dash and starting yesterday my car has experienced rough shifting from 1-2 and 2-3 gears both on...


This may be related to converter, the converter may be plugged, this will cause problems with the shifting, have the computer scanned for any stored codes. also make sure to have the 02 sensors checked.

Sep 17, 2010 | 2006 Volkswagen Jetta

1 Answer

Getting spark to distibutor but not to the spark plugs


sounds like the rotor arm or distributor cap check carefully for cracks

Oct 16, 2009 | 1997 Volkswagen Jetta

1 Answer

2000 Jetta 1.9 TDI is reading 2 codes for electrical connecton


The torque converter clutch circuit is built onto the tranny. You can see the plugin. You can disconnect this and will be ok, Otherwise it is expensive to fix

The crank sensor sends informaiton to car's computer telling it to give power to the motor. If the crank sensor is shot, then your car probably will turn over but won't start. Or won't always start until it is completely bad and won't start at all.

You can go to autozone.com and register for free, then you will have a full free online repair manual

Aug 05, 2009 | Volkswagen Jetta Cars & Trucks

2 Answers

Firing order for plugs to distibutor


Firing order is 1  3  4  2  and start at one, (the top) go one at a time, and move in a clockwise rotation.  looks like this:
                                                                   1 
                                                            2              3                                                                        4

Mar 21, 2009 | 1997 Volkswagen Jetta

1 Answer

Enginge is out of timing


If you removed the distibutor you need to pull #1 spark plug and turn the motor over by hand till you reach TDC or top dead center. Put your finger over the spark plug hole and have someone turn the crank until you feel pressure then check your timing marks in conjunction with the timing tab on the harmonic balancer and the timing chain cover. Line them up, turn the rotor on the distibutor to where the #1 plug wire point is at on the cap and drop it back in you should be close or on. This is if when you replaced the timing chain and gears you installed them properlly with the marks on the gears lined up.

Dec 18, 2008 | 2001 Ford Explorer

Not finding what you are looking for?
1995 Audi S6 Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14848 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...