Question about Cars & Trucks

1 Answer

I have changed the output shaft speed sensor on my 2004 mondeo auto and the fault codes P0720 and P0722 have not gone away. Any ideas would be appreciated.

I have replaced the output shaft speed sensor as codes p0720 and p0722 came up on diagnostics, but replacing part has not made the codes go away? Can you please assist?

Posted by Kyri christofi on

Ad

1 Answer

aph1

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 139 Answers

Lock the car and then unlock

Posted on Dec 12, 2014

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What are the probable causes of DTC P0720?


According to the database the code means OUTPUT SPEED SENSOR CIRCUT MALFUNCTION.

Dec 12, 2015 | Cars & Trucks

1 Answer

2000 ford f250 7.3 4r100 code p0720 changed the output shaft speed sensor and still getting the delayed shift and code dont know what to dob


bad connections, Definition of Diagnostic Trouble Code P0720 Category: Powertrain Definition: Output Speed Sensor CircuitNote: This definition of P0720 is applied to all manufacturers

Jul 23, 2015 | Cars & Trucks

1 Answer

2001 Hyundai Accent Output shaft speed sensor


output shaft speed sensor on top transmission. just depress the release tab disconnect electrical connector then remove output shaft sensor bolt.remove sensor.

Jul 15, 2013 | 2001 Hyundai Accent

1 Answer

P0720 stratus codes


code p0720 refers to output shaft speed sensor(OSS)--circuit malfunction====causes--wiring--OSS sensor--ECM/TCM
of it has just happened check the wiring and connections to the transmission for water and corrosion or replace the OSS sensor in the transmission.

May 08, 2013 | 2002 Jeep Liberty

1 Answer

Trouble Code- p0722 output shaft speed sensor no signal


Here are the possibilities.
Possible causes- Speed sensor harness or connectors
- Sensor circuit is open or shorted
- Speed sensor

Jun 14, 2012 | 2006 Honda Accord 3.0

1 Answer

My 2009 Hyundai Sonata quit accelerating while driving in town. The ESC and check engine light came on. I was able to turn the car off and back on and the ESC light went off and acceleration worked...


This may not be your problem but it does bring the vehicle in fail safe you may have a warranty
Group TRANSAXLE
Number 09-AT-016
Date AUGUST, 2009
Model
1999-SONATA
2001-ELANTRA, SANTA FE & XG
2003-TIBURON
2005-TUCSON
2006-AZERA
2007-ENTOURAGE

Subject
AUTOMATIC TRANSAXLE DIAGNOSTIC TROUBLE CODES P0715, P0716, P0717, P0720, P0721 & P0722

An improperly functioning input speed sensor or output speed sensor may result in the following conditions:
^ "Check Engine" light on
^ Harsh P-R or P-D engagement shock
^ Transaxle in 3rd gear fail-safe
^ Diagnostic trouble codes 1. Using a GDS, check for DTCs in both the "Engine" and "Automatic Transaxle" menus. Record the DTC and description.
2. From the GDS, select:
^ Vehicle
^ "Auto Transaxle" menu
^ "Current Data"
^ "Input speed sensor" and "output speed sensor". Drive the vehicle and monitor the input and output speed sensors. If the sensors show:
^ Continuous output, the wiring currently has no open/shorts. Go to Step 6.
^ No output, go to Step 3
3. Check the wiring harness visually for an open circuit or short circuit to ground. Check for a pinched harness at the PCM/TCM attachment bolts.
4. Disconnect the connectors at the input and output speed sensor and PCM/TCM. Check for bent pins or pins not fully inserted into the connector.
5. If a harness open/short is found, repair or replace the ECM control harness between the PCM/TCM and transaxle and go to Step 8. If not, go to Step 6.

Aug 22, 2011 | Hyundai Sonata Cars & Trucks

1 Answer

What does code 720 diagnostic mean


P0720 = output speed sensor malfunction.

This is a sensor on the transmission that shows output shaft speed. Either it is malfunctioning or the wiring to the sensor is faulty.

Mar 14, 2011 | Dodge Ram Pickup 1500 Cars & Trucks

1 Answer

My speedometer will not work check engine light goes on and off and the overdrive indicator light flashes. All this happens intermittently with hotter weather it seemingly happens more frequently. Scanned...


code p 0500 is for the vehicle speed sensor (VSS) which works the speedo as well as the ratio changes
code p0720 refers to the output shaft sensor --ECM or transmission control module (TCM)
the vss reports to the tcm which reads the road speed and gear ratio and shifts the appropriate solenoid

May 12, 2017 | Cars & Trucks

1 Answer

Check engine light with following codes p 1529 p0720 p0715


P1529 indicates that your TCM asked the ECM to turn on the check engine lamp.

The range switch and the output speed sensors are the items that are abnormally affecting the operation of the transmission. The diagnostic logic in your computer can distinguish these issues from one another, so you'll definitely want to do both. You have no diagnostic code for the input speed sensor (P0715) listed, so I have made no recommendation to replace it. In my opinion, it's not a labor-intensive repair, so I wouldn't recommend replacing it unless you have reason to believe it's bad.

DTC - P0720 (OUTPUT SHAFT SPEED SENSOR SYSTEM)
Code No. P0720 Output shaft speed sensor system
If the output from the output shaft speed sensor is continuously 50% lower than the vehicle speed for 1 second or more while driving in 3rd or 4th gear at a speed of 30 km/h or more, it is judged to be an open circuit or short-circuit in the output shaft speed sensor and diagnostic trouble code No. P0720 is output. If diagnostic trouble code No. P0720 is output four times, the transmission is locked into 3rd gear or 2rid gear as a fail-safe measure.
Probable cause
Malfunction of the output shaft speed sensor
Malfunction of the transfer drive gear or driven gear
Malfunction of connector
Malfunction of the TCM

DTC - P0715 (INPUT SHAFT SPEED SENSOR SYSTEM)
Code No. P0715 input shaft speed sensor system
If no output pulse is detected from the input shaft speed sensor for 1 second or more while driving in 3rd or 4th gear at a speed of 30 km/h (19 mph) or more, it is judged to be an open circuit or short-circuit in the input shaft speed sensor and diagnostic trouble code No. P0715 is output. If diagnostic trouble code P0715 is output four times, the transaxle is locked into 3rd gear or 2nd gear as a fail-safe measure.
Probable cause
Malfunction of the input shaft speed sensor
Malfunction of the underdrive clutch retainer
Malfunction of connector
Malfunction of the TCM

Is needed replace.

Nov 04, 2009 | 2001 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

387 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

23438 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...