How do i program my key remote for toyota rush

1.   Close and lock all doors with the driver’s side power lock/unlock switch.

2.   Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast, system will not enter programming mode.

3.   Insert key into the ignition cylinder and turn to the ACC position.

4.   Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful.

5.   If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should flash. Repeat this step for each transmitter (including any existing transmitters).

6.   Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.




Make sure you have the right fob for your car.

1. Close and lock all doors with the driver's side power lock / unlock switch located
on drivers door panel.

2. Insert key into ignition and remove it from the ignition key cylinder at least 6 times
within 10 seconds. Your hazard lamps will flash if you have performed this step
successfully. NOTE: Withdraw key completely from ignition cylinder each time. If
this procedure is performed to fast, system will not enter programming mode.

3. Insert key into ignition and turn to the ACC position.

4. Within 5 seconds, push ANY button oon the keyless remote. Your hazard lamps
will flash. NOTE: Do not press the button on the remote more than one time or the
programming will not be successful.

5. If there are any remaining remotes (including old ones), Unlock then Lock all doors
using switch on drivers door panel and within 5 seconds press ANY button on the next
remote. Your hazard lamps will flash. Repeat this step for each remote (including any
existing remotes).

6. Turn key to the off position, remove key from the ignition. Unlock door using switch on
door panel and open drivers door.

7. Test remote(s).

Free Nissan Keyless Remote Programming Replacement Key Keyfob Maxima...

2004 Nissan Maxima Key Fob Programming Instructions

2004 Maxima

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.

1. Close and lock all doors with the driver's side power lock/unlock switch.
2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast, system will not enter programming mode.
3. Insert key into the ignition cylinder and turn to the ACC position.
4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful.
5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver's side power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should flash. Repeat this step for each transmitter (including any existing transmitters).
6. Turn the key to the OFF position, remove keys from the ignition,
   unlock doors using the driver's side power lock/unlock switch and open the driver side door.

Few Toyota models came equipped with remote door locks before 2008 - surprisingly!

Your car may not have the radio receiver to work with door locks. In that case, you need the radio and some wireing to pair with your remotes.

It may be that water/moisture has gotten in behind the door panels...do you notice that it worsens in damp(er) weather? The car unlocks by itself if you leave the key in the ignition and you try and lock the doors.

Or somebody has the same coded fob (unlikely).

You might want to reprogram the remotes if you determine that the area behind the door panels is dry and there are no corroded wires, etc.

https://youtu.be/30TBRP1Mn5w

Good Luck.

2004 Nissan Quest Remote Programming Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
1. Close and lock all doors with the driver's side power lock switch located on drivers door panel.
2. Insert key into ignition (DON'T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver's side power lock/unlock switch and open the driver side door. Test all remotes.

it is not the actuators, try a different remote, you may have an issue with the car security system/body computer not functioning on the unlock driver door command, one press of remote is unlock driver door and 2 presses is unlock the other doors.

Obtain all keys/remote controls. Remove driver's side kick panel/lower 'A' pillar trim. Connect central locking registration connectors (white) - black wire and black/blue wire Fig. 2 . Unlock the vehicle using the key. Program first key/remote control as follows: Press unlock button Fig. 1 [1], then lock button [2]. The door lock should lock and unlock in sequence confirming programming of first key/remote control. Repeat programming procedure for remaining key(s)/remote control(s). Once the last key/remote control is programmed disconnect central locking registration connectors. Check operation of all programmed keys/remote controls.

The horn chirp can be disable by pressing the lock and unlock buttons simultaneously until the hazard lights flash, and no enable press the lock and unlock until the horn chirp.
To reprogram (enter new ID) key fob (keyless remote controller) follow the steps.
1. Close all doors and lock all doors
2. Insert and remove the key from the ignition key cylinder more than six times within 10 seconds. (The hazard warning lamp will then flash.) NOTE: Key should be withdrawn from ignition key cylinder completely each time.
NOTE: Do not rush the insertion/removal key cycling process. The side marker/tail/license lamps and interior illumination will flash twice when this step is accurately completed.
3. Insert key on ignition key cylinder and turn ignition key switch to "AAC" position At this time, the new ID code is entered and original (previous) ID codes are erase.
4. Press any button on the new remote controller once. (The hazard warning lamp will then flash)
NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful. The side marker/tail/license lamps and interior illumination will flash twice when this step is accurately completed and programming is successful.
If there is only one remote controller skip step 5.
5. Additional ID code entry Release the door lock, then lock again with door lock/unlock switch (In power window main switch)
6. Remove key from ignition
7. Unlock driver side door, open driver side door and then close the door. (END)

Program your factory keyless entry functions
For 2001+ Tacomas equipped with a factory alarm or keyless entry, here are some programming options that allow you to adjust the way your locks work.
The first programming option allows you to set the entry unlock to: (A) unlock the driver door with one push, and the remaining doors with a second push OR (B) unlock all of the doors with a single push.

• Open the driver's door. Remove the key from the ignition switch.
  
• (Complete these steps within 40 seconds)
  
  1. Insert the key into and remove it from the ignition switch 2 times.
     (IN - OUT - IN - OUT)
     
  2. Close, then open the driver's door 2 times.
     (SHUT - OPEN - SHUT - OPEN)
     
  3. Insert the key into and remove it from the ignition switch 1 time.
     (IN - OUT)
     
  4. Close, then open the driver's door 2 times.
     (SHUT - OPEN - SHUT - OPEN)
     
  5. Insert the key into the ignition switch and leave it in.
     
  6. Close the driver's door.
     
  7. Turn the key from LOCK to ON 4 times, ending at LOCK
     (LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON - LOCK)
     
  8. Wait for the locks to stop, then remove the key from the ignition switch.
     
• On the key fob, press and release both LOCK and UNLOCK buttons at the same time.
  
  1. [For all doors unlock] press and release the UNLOCK button.
     
  2. [For driver door unlock] press and release the LOCK button.
     
• Open the driver's door. The programming is complete. If programming did not occur, start over.

Close all vehicle doors, LOCK doors using drivers side switch.

Insert key all the way into the ignition, (do not turn) remove key.

Repeat this step 5 times. (6 total)

Hazards should flash to indicate program mode.

Press any button on transmitter to be programmed, hazards should flash to indicate successfull program.

*For additional remotes, cycle drivers door lock UNLOCK, LOCK, press any button on remote, hazards should flash. Repeat step as necessary.

Ignition ON, (engine off) ignition OFF, UNLOCK using drivers side switch, test remotes.

Source