Question about Mazda Cars & Trucks

1 Answer

How do I remove and change ignition switch in a mazda bravo 2001 ute?

Posted by Jo Hodges on

Ad

1 Answer

k spencer

  • Level 1:

    An expert who has achieved level 1.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 17 Answers

Hi, 1st you need to take off the steering wheel, if the horn does not just pop off, check for 3 torque bit 8mm at the back of the steering wheel, they could be star point screws, depending on where is was built. be sure your wheels are true straight, and lock ignition so wheel not turn, it makes it easier to put the s wheel on true again, With the nut keeping the s wheel on, just crack it a little, then with a brass drift, give it a good hard quick hit, as its on a spicket & can cold freeze on, some come off easy, but what ever you do, don't flog nut with hammer, use brass as its softer than tempered steel,
Once you have s wheel off, 3 screws under the column, 2 one side of the tilt lever & one the other side, make sure u note which one come out of what holes, as they differ in length, then pop off the top plastic cover, ( un clip airbag wire from horn pad, ), no need to disable battery), once both cover are off, you will see 2 screws holding the ignition lock in place, could be torque head, or just a 8 mm nut,) unclip the plugs, and take out , do the reverse to fit back together, if you source on from Auto Wreckers, make sure it has the correct key, to suit that ignition, as they are coded, Good luck
K

Posted on Nov 26, 2014

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a mazda bravo 2 wheel drive ute I can start car and press in clutch place in gear and release clutch and take of but then can change into next gear and with foot on clutch the car still moves


This sounds like the clutch, at the engine end, has a problem. The clutch plate might not be releasing correctly. When the engine is Off the clutch isn't spinning so doesn't affect the gear change. You might need to have the clutch replaced.
Your only sensible option is to get a Good Mechanic to remove the gearbox and inspect the clutch parts.
This, unfortunately, will not be a cheap fix.

Sep 11, 2018 | Mazda Cars & Trucks

1 Answer

Ford Couirier/Mazda Bravo 1994 2.6 petrol 4x4 B2600 I need to buy new/used ECU (G618) replacement or upgrade for my 4x4 ute I want to know the compatible units i can use and best place to get one.


the ecu has to come out of the
same year and number as the engine and drive line
Ford Courier/Mazda Bravo 1994 2.6 petrol 4x4 B2600
source from
ebay
a 4x4 wrecker
an good auto electrican can referb your original
this is usa but might be a seller some where in australia

edit I added image of a G695
http://www.ebay.com/itm/OEM-91-92-93-MAZDA-B2600i-TRUCK-ENGINE-COMPUTER-CONTROL-MODULE-ECU-G618-18-881A-/1916530508691a07fc2d-2613-4d2f-a996-9a4d38ad626f.jpgford-couirier-mazda-bravo-1994-2-6#sln-36462275-ynwsor2g41t5qaon3uf1gyaf-5-2_2.jpgford-couirier-mazda-bravo-1994-2-6-ynwsor2g41t5qaon3uf1gyaf-5-3.jpg

Sep 11, 2016 | Ford Cars & Trucks

1 Answer

1992mazda bravo ute has no compression


check that the cam shaft is turning ( broken belt/chain)

Mar 28, 2015 | Mazda Cars & Trucks

1 Answer

Hi I have a mazda bounty/bravo 2005 2.5 td wl engine. The engine has a a slight tapping noise once it reaches operating temp.it is more noticeable at idle. I have done the tappets to spec but that didn't...


First I'd put a manual oil pressure gauge on it to verify it's holding proper pressure. If it passes the test it could be as simple as a collapsed oil filter or possibly a bad lifter.

Feb 18, 2015 | Mazda Cars & Trucks

1 Answer

2004 Mazda Bravo 2.6 efi


sounds like a blown head gasket or your engines locked up

Feb 16, 2014 | Mazda Cars & Trucks

1 Answer

1998 mazda bravo ute b2600 petrol- Cannot locate the oil filter to change. Can find the sump and bung. Is it possible this model has no oil filter?


No!!!! The motor has oil filter.Look from the top of the motor.It is right there.Under the manifold.Hope this helps

May 25, 2011 | 1998 Mazda B-Series

2 Answers

Changing gearbox oil ?


i accidently drained some of the gearbox oil from my bravo b2600 1997. where is the hole to put more fluid back in there? how much should i put? and what fluid should i use?

Dec 26, 2009 | 1999 Mazda B-Series

2 Answers

Strange Problem Bravo Ute Air Conditioning


the blower motor has no affect on the AC system,
start the engine and turn on AC and watch the AC compressor to see if clutch engages,if it doesn't the system isn't full,if you are correct the clutch should be engaged and should quit when you change heater speeds,

Dec 23, 2009 | 1988 Mazda B2600 Cab Plus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

385 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6499 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...