How do I reattach rear window to convertible top?

There are only Two things in the right rear the pump motor and the top ajar switch. This sounds like the motor is locked up or the top is jammed or going the wrong way. First disconnect the motor and if the noise stops it's the hydraulic unit trying to move the top watch the top to make sure it's going the right way, the top ajar switch could be bad. If you're confident in the hydraulic unit and motor the only thing left is a jammed top, a bad connection at the hydraulic unit, or the top ajar switch. I hope this helps. Take care.

Principles of Operation
Convertible top operation is controlled by the smart junction box (SJB). When the convertible top raise/lower switch is operated, the SJB commands the front and rear windows to the full down position. Window operation is disabled while the convertible top raise/lower switch is being operated. When the SJB receives a full down input for both rear windows, it commands the appropriate relay closed to raise or lower the convertible top. If the SJB does not receive a full down input signal for both rear windows, the convertible top operation is disabled.

The convertible top hydraulic system uses a 12 volt reversible pump and motor assembly. When active, the pump uses hydraulic pressure to extend the hydraulic lift cylinders to raise the convertible top, or retract the hydraulic lift cylinders to lower the convertible top. The convertible top motor/pump assembly is equipped with a thermal circuit breaker. The circuit breaker typically resets after 5 minutes depending on the ambient temperature. The thermal circuit breaker cannot be repaired and must be installed as a unit with the motor/pump assembly. In the event of a hydraulic system failure, the convertible top cannot be operated manually.

Inspection and Verification

1. Verify the customer concern.

1. Visually inspect for obvious signs of mechanical or electrical damage.

Visual Inspection Chart Mechanical Electrical

• Convertible top brackets and frame
• Convertible top latches
• Convertible top pump and motor assembly
• Hydraulic lift cylinders
• Hydraulic lines

• Bussed electrical center (BEC) fuse(s):
  • 13 (40A)
  • 51 (10A)
• Circuitry
• Convertible top pump and motor assembly
• Convertible top ajar switch
• Convertible top switch
• Connector(s)
• Convertible top raise relay
• Convertible top lower relay
• LH or RH rear power window motor
• Smart junction box (SJB)
• BEC

1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

1. If the cause is not visually evident, connect the scan tool to the data link connector (DLC) and select the vehicle to be tested from the scan tool menu. If the scan tool does not communicate with the vehicle:
   • check that the program card is correctly installed.
   • check the connections to the vehicle.
   • check the ignition switch position.

1. If the scan tool still does not communicate with the vehicle, refer to the scan tool operating manual.

1. Carry out the scan tool data link test. If the scan tool responds with:
   • CAN or ISO circuit fault; all electronic control units no response/not equipped, refer to Section 418-00 .
   • No response/not equipped for SJB; refer to Section 419-10 .
   • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs, and carry out self-test diagnostics for the SJB.

1. If the DTCs retrieved are related to the concern, go to the Smart Junction Box (SJB) Diagnostic Trouble Code (DTC) Index.

1. If no DTCs related to the concern are retrieved, GO to Symptom Chart .
2. Smart Junction Box (SJB) Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1141 Convertible Top Full Down Position Switch Circuit Failure SJB Go To Pinpoint Test E . B1142 Convertible Top Full Up Position Switch Circuit Failure SJB Go To Pinpoint Test E . B1402 Driver Power Window Down Switch Circuit Failure SJB Go To Pinpoint Test A . B2068 Convertible Top Up Output Circuit Failure SJB Go To Pinpoint Test A . B2069 Convertible Top Down Output Circuit Failure SJB Go To Pinpoint Test A . B2481 Convertible Top Up/Down Switch Fault SJB Go To Pinpoint Test A . B2578 Passenger Power Window Down Switch Circuit Failure SJB Go To Pinpoint Test A . All Other DTCs - SJB Refer to Section 419-10 .
3. Your best bet ,take it to a qualified repair shop !

A shop that works on boat covers, canvas awnings, or convertible tops should be able to repair it.

The rear windows are controlled by a timer in the top's ECU. If
the rear windows stop fully closing before your top is closed, the
problem MAY be with top's hydraulic system.

Check your top's hydraulic reserve tank for low fluid level. Lack
of fluid will greatly delay the top's closing sequence, leaving
those rear windows partially open.
Your top's hydraulic pump system is located beneath the right side
of the cubby/storage box behind the front seats. Raise the cover
and you'll see a removable trim panel on the right side. The pump
is behind that access panel.

You can use power steering fluid to top off the tank, but don't
fill it above level indicator line. You may have to add more fluid
after you cycle the top up and down to get the air bubbles out of
the lines.
It could also be a relay. On a 95 the relays that are in the trunk above the battery.
Perhaps, just switching the relays might prove which one is failing..

do you see any visible reddish in color in the vehicle or on the floor ?

Plexi works fine, but it doesn't have the embedded heating wires. To replace the glass normally requires that the hood section below it be replaced with it. This usually means removal of the hood material from the back of the car, and reattachment by staples to the mounting strip. Most suppliers have instructions on how to do this.

If you get a good used rear window, you might be able to simply 'unglue' the feature strip (that's the hood material below the glass) and reattach it to the 'new' window with 3M's special adhesive for this.

This link will give you some ideas: http://www.convertibletopguys.com/topmanual.shtml

Good luck!

Here is an idea!

Unfortunately, this is not something you can fix yourself. You will need to take the car to either the dealer or a shop which specializes in fixing convertible tops, headliners, etc (commonly called an automotive trim shop) Most used car dealers have a trim shop that they can recommend.

Charlie

It worked. Still very stuck with no signs of coming loose and I did it about a month ago. Just dont use too much and apply it with a little paint brush like an artist would use. You can always add more, but if you use too much, it will look messy. I used a little much in two places and when it expanded, you could see the yellow foam it makes at the edge of the fabric. But I just shaved it off with a razor blade and it looks fine. After doing the outside, gluing the glass to the fabric, i also glued the headliner in place as well. I lowered the top a few inches to take the pressure off, and put just a little glue in the track around the inside of the window, then put the edge of the headliner in the track. Left it overnight and it has not come loose since. I think getting this headliner reattached is important cause the headliner actually pulls the glass against the fabric top, which takes pressure off of the glue holding the window in place. In retrospect, maybe if i had fixed the headliner earlier, the window might not have come unglued in the first place. Shame on VW for not dealing with this issue better. Replacing the entire top is ridiculous!