Question about 2005 Toyota Corolla

1 Answer

WHERE ON A 2005 TOYOTA COROLLA IS THE PURGE VALVE LOCATION

Posted by Anonymous on

Ad

1 Answer

Thomas Perkins

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 14,848 Answers
Ad

5 Related Answers

Anonymous

  • 101 Answers

SOURCE: where is the pcv valve on 2005 toyota corolla

Remove the plastic engine covering the top of the engine by removing the 2 10mm nuts. Pull the cover off and standing in front of the car looking at the engine,the pcv is located in the rear of the valve cover on your left. There is a 3/8 id hoses attached to it. Pull the hose off and unscrew the valve with a 22mm socket..
If you look down at your exhaust manifold you will see a sensor sticking out that looks like a o2 sensor. It is not. Its an air fuel ratio sensor and it works totally different then a o2 sensor.THis is the sensor that helps adjust the air fuel mixture. If you follow the exhaust system back under the car about 1/2 way you will see another sensor in the exhaust . This is the o2 sensor and is used to monitor the condition of the convertor.
If you need one of these sensors you will have a check engine lite on with a AF or o2 code.

Posted on Apr 16, 2009

Ad
okcfirewall

okcfirewall

  • 80 Answers

SOURCE: Where is engine Number Location for Toyota Corolla

if your looking for the engine details lift the hood of the car and there will be a sticker on the hood to the right about eye level it will have the details of the engine it should say something like 2.4L and then give details about emissions and the car......................... I hope this helps

Posted on Jul 20, 2009

Anonymous

  • 305 Answers

SOURCE: 2005 Toyota Corolla Radio fuse

Pg. 250 of your 2005 Owner's Manual shows the location of the Fuse Boxes. There is one under your hood on the driver's side and the other is under the dash just to the left of steering wheel. Pg 272, will show you how to replace the fuses. Pg. 286-287 gives a diagram and description of each fuse and what part of the electrical system it enables.
This portion of the electrical system correspondeds to the fuse in position 32 on pg. 287 of the manual.
Your going to have to get on your back with a flashlight and open up the fuse box under the dash by the steering wheel. The lid of the fuse box shows the positions of the fuse and their amperage rating. Like I said, replace the fuse in postion 32 (15 Amp). There is a spare 15 Amp fuse in the fuse box under the hood (easy to get to, see the diagrams in the owner's manual). There is also a fuse puller tool next to the spare fuses.

Posted on Aug 11, 2009

Superbovine

  • 333 Answers

SOURCE: 2005 toyota corolla motor oil capacity?

if you have a 1ZZ engine

4.2 quarts, 4.4 quarts with oil filter change

if you have the 2ZZ engine (XRS model) it is

4.4 quarts, 4.6 quarts with oil filter change

NOTE these are updated capacities that reflect changes identified in TSB: TSB-0134-08 issued July 15, 2008.
Your owners manual will reflect a lesser quantity that Toyota has since revised.


Posted on Sep 10, 2009

Superbovine

  • 333 Answers

SOURCE: How do I remove brake drum on 2005 toyota corolla

Under normal circumstances, the drum should slide right off once the wheel is removed.

If you have built up rust holding it on, there are two threaded holes near the center of the drum to aid in removal.
Insert two 12mm bolts into the holes and, while adding plenty of lubricant, turn the bolts in even amounts until they push the drum off.
Be sure to keep them lubed, as they will strip out easily if not.

If you have aftermarket drums without the holes or the screwholes are stripped out, smacking the face of the drum with a dead blow hammer will help free it up, but takes much longer for success.

Posted on Oct 17, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it possible that 1995 toyota corolla doesn't have EGR valve?


1995 Toyota Corolla 1.8L EFI DOHC 4cyl

The EGR Valve is located: Under hood, center, upper engine area, mounted on upper rear of engine near valve cover.Here's a link to what it look's like. EGR Valve at AutoZone com Best EGR Valve Products for Cars Trucks SUVS

Feb 14, 2016 | 1995 Toyota Corolla

1 Answer

2005 Toyota Corolla. How do I replace the EGR valve?


THE EGR IS HELD IN PLACE BY BOLTS. REMOVE THEM AND REPLACE EGR VALVE

May 07, 2015 | 2005 Toyota Corolla

1 Answer

Where is the location of the tcc solenoid on my 2005 corolla


Inside the trans pan next to all other solenoids in the valve body, if u have less than I believe 75000 miles toyota should address the issue for you. This is in a technical service bulletin, short fall ofa recall.

Apr 15, 2015 | 2005 Toyota Corolla

1 Answer

05 corolla, after gassing up, whether partial or full fillup, car is hard to start. will crank but runs rough before going dead. after 3-4 starts and runs fine. toyota dealer checked codes; po 171 system...


Sounds like you may have an issue with the check valve on your in tank fuel pump. When these go bad, you have to crank several time to build up enough pressure in the fuel rail for engine start. With a good check valve, the fuel pressure will not bleed off and the pressure is retained for the next engine start.

Oct 27, 2010 | 2005 Toyota Corolla

2 Answers

1998 toyota corolla , took it to shop, eng lite on . they pulle'd code-PO441--- incorrect purge flow . can any one tell me beside,take it to dealer or that it's an EVAP problem, what is,where, the...


There is usualy a problem with the Delta pressure feedback system when this code is present. Its usualy mounted near the egr valve and most times will have two silicone high temp vacuum hoses connected to it. First make sure the hoses are connected, is so try replaceing it to solve the problem.

Apr 21, 2010 | 1998 Toyota Corolla

1 Answer

Pressure Control Solenoid "D" location on a 2005 Toyota Corolla?


this solenoid is part of the solenoid pack that is located on the valve body inside the transmission.

Mar 28, 2010 | 2006 Toyota Corolla

1 Answer

I scann my car 2005 corollathe code came p0441and p0445 what does it mean engine light blinking


p0441: Evaporative Emission Control System Incorrect Purge Flow;
A code P0441 could mean one or more of the following has happened:

Bad vacuum switch
  • Broken or damaged EVAP line or canister
  • Open in PCM purge command circuit
  • Open or short in Voltage feed circuit to Purge Solenoid
  • Faulty purge solenoid
  • Restriction in EVAP solenoid, line or canister
  • Corrosion or resistance in purge connector
  • Bad PCM

p0445: Evaporative Emission Control System Purge Control Valve Circuit Shorted
(This also came up already above)

Nov 30, 2009 | 2005 Toyota Corolla

3 Answers

P0440,p0441,p0446


These codes are all for the Evaporative Emissions System.

P0440- Evaporative emissions system fault- just saying there's something wrong with the system.

P0441- Evaporative emissions system- Incorrect purge flow- saying that the system isn't purging the raw fuel vapors (hydrocarbons- HC) as well as it should.

P0446- Evaporative emissions system- Control valve circuit low- there is a valve, usually located on the charcoal canister at the rear of the vehicle, that opens to allow fresh air to enter the evaporative emissions system as the engine vacuum purges the fuel vapors from the charcoal canister and closes when purge is not needed to prevent leakage of those fuel vapors to the atmosphere (HC is a greenhouse gas and is regulated as such by the fed gov't).

Given that you have the incorrect purge flow code and the control valve code together, my bet is that the vent control valve has failed (causing the P0446) and is not opening to allow fresh air into the system to displace the air from within the system that is being pulled to the engine. Since you have no fresh air entering the system, the engine will pull a vacuum on the system instead of the vapors "flowing" into the engine (causing the P0441).


I hope that this is helpful to you!!!


ASE Master Technician with L1 and X1 Certifications; Nissan Scope Technician; Chrysler Level 3 Silver Technician- 12+ years experience.


Nov 17, 2008 | 2001 Toyota Corolla

Not finding what you are looking for?
2005 Toyota Corolla Logo

905 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...