Question about 2000 Daewoo Leganza

Open Question

How do I replace Crankshaft Pulley on a 1999 Daewoo Leganza?

Need repair info to replace serpentine crankshaft pulley after it just fell off the car and into my hands.

Posted by Anonymous on

Ad

2 Related Answers

Greg Mills

  • 497 Answers

SOURCE: WHERE CAN I BUT A CRANKSHAFT PULLEY FOR A 2000

You can try www.autozone.com they normally have the best deals. Otherwise youre local autoparts store should be able to order one for you if they dont have it in stock.

Posted on Aug 09, 2009

Ad
stevenhurc

Steve Hurc

  • 459 Answers

SOURCE: Daewoo Matiz crankshaft pulley

remove the outer small bolts to remove balancer(pulley) the big centre bolt holds crankshaft gear for timming belt which slides off with timming belt removed.

Posted on Sep 13, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi all, hard time with serpentine belt replacement on my Hyundai Santa fe 2004 2.4l dohc. The problem is the two serpentine belt situation, I dont know how properly overlap the smaller one over gen


Hi Alex,here's a Autozone repair guide link showing you your belt diagram. SAVE 20 ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE Look's like both belts are using the crankshaft pulley,The alternator,the water pump and the crankshaft pulley is using one belt.Need more help,let me know.

Sep 19, 2016 | 2004 Hyundai Santa Fe

2 Answers

95 LeSabre 3.8 serpentine belt removed you can turn crankshaft pulley forward and back about an inch and a half makes loud noise at times car still runs and drives possible broken crankshaft?


you should be able to turn it by hand or with a socket and ratchet broken crank means broken car if you broke crank which is rare you would not have a running engine sounds more like stretched timing chain if it feels sloppy

Jul 29, 2015 | Cars & Trucks

1 Answer

2005 santa fe serpentine broke then bad vibrating and it died replaced serpentine and tensionor, now motor locked. Is the motor shot or could something else be wrong?


Put a socket and wrench on the crankshaft pulley bolt, and see if you can turn the crankshaft-clockwise. If the crank won't turn, something internal is bad. If you can turn the crankshaft normally, check that another pulley has seized.
Or try it this way: take the serpentine belt back off and see if the starter can spin the crankshaft. If it does, look for a seized pulley. If a good battery cannot make the starter turn the crankshaft, likely the motor is shot.

Aug 15, 2014 | 2005 Hyundai Santa Fe GLS

2 Answers

1997crank pulley fell off bolt snapped need to repair


So, go ahead and repair it. You don't need our permission.

May 28, 2014 | Cars & Trucks

1 Answer

Hi im having trouble removing the small allen head bolts that hold the crank pulley on on a 1999 daewoo leganza 2.2l are the left or right hand thread . im trying to remove them to take off the timing belt...


You will not need to remove the crankshaft pulley. There will be a belt tensioner that you release to be able to remove the belt. But im not familiar with your car.

Open this link, the tensioner is pictured:

https://www.napaonline.com/Catalog/CatalogItemDetail.aspx?A=NBHT43106_0323240851&An=599001+101999+50019+2019002+28951&Ar=AND(P_RecType%3aA)

Looks like you release it with socket bit with an allen wrench.

Rotate the tensioner and you can remove the belt from the tensioner, then release the tensioner after you pull the belt off the pulley.

Sep 20, 2011 | Daewoo Leganza Cars & Trucks

1 Answer

How do I replace the Airconditioning/power steering belt on a Grand marquis, Mercury(1992)? please show me in a diagram or print somehow


Move the Grand Marquis's serpentine belt tensioner off the serpentine belt with the serpentine belt tool. Pull the belt of the remaining pulleys by hand. Take the belt out of the engine well. Wrap the new belt around the bottom portion of the crankshaft pulley. Follow the belt routing diagram to route the belt over each remaining pulley until only the tensioner remains. Move the Grand Marquis's serpentine belt tensioner aside once more and slip the belt onto the tensioner pulley.Hold the belt in place with one hand while you move the tensioner slowly back into position with the other. Here you can fine the quality AC parts http://www.1airconditioning.com/ac_compresor.htm

Aug 24, 2011 | 1992 Mercury Grand Marquis

1 Answer

My crankshaft pulley is very loose, can i tighten it?


The bearings are most likely shot. You will need to replace the pulley, check the bolt its prob tight.

Mar 20, 2011 | 2002 Daewoo Leganza

1 Answer

WHAT IS CORRECT TIMING MARKS FOR TIMING BELT INSTALLATION. 2000 NUBIRA 2.0 DOHC AND CRNKSHAFT MARKS. Thanks Joe


TIMING BELT
Removal
Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing.
Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt.
Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle.
Support engine assembly from above with Support Fixture (J-28467-B). Remove engine mount bracket from timing belt end of engine.Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).
Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 .
CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover.
Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. Remove timing belt.
Fig. 4: Aligning Crankshaft Sprocket Timing Mark
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim_4.jpg
Fig. 5: Aligning Camshaft Sprocket Timing Marks
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim2_3.jpg
Installation
Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS .
Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch.
If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt.
Install right front splash shield. Install right front wheel. Install air filter housing and resonator. Connect air intake temperature sensor connector. Connect negative battery cable.
Fig. 7: Identifying Timing Belt Routing
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim3_1.jpg
here

http://www.2carpros.com/questions/daewoo-leganza-2000-daewoo-leganza-timing-marks

Feb 17, 2011 | 2000 Daewoo Nubira

1 Answer

LOOKS LIKE MY 99MAXIMA CRANKSHAFT PULLEY BELT BROKE AND THE PULLEY IS KINDA HANGING OFF SOME, WHAT AM i LOOKING AT? JUST BELT AND IS PULLEY OK OR REPLACEMENT OF BOTH? PLEASE HELP DONT WANT TO GET RIPPED...


If it's the main pulley that connects to the crankshaft and drives the serpentine belt, it's called the dampener pulley.
If the dampener pulley has worked loose or separated, you'll need to replace any damaged components, possibly including the pulley, mounting bolt and even the crankshaft and front engine housing could have been damaged if the pulley continued to turn while it was loose.
It could be as simple as tightening the bolt or as severe as a major engine rebuild. A mechanic can't know until he takes a look at it.

Feb 07, 2011 | 1999 Nissan Maxima

Not finding what you are looking for?
2000 Daewoo Leganza Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23515 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...