How to remove front passenger side seat

it wont show active since you will be disconnecting the wiring

There is no relay for the passenger side air bag . What seams to be the trouble ? There is possibly a code set in the air bag control module .
Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) The air bag supplemental restraint system (SRS) is designed to provide increased collision protection for front seat and second row outboard occupants, in addition to that provided by the 3-point safety belt system. Safety belt use is necessary to obtain the best occupant protection and to receive the full advantage of the SRS.
This vehicle line contains dual stage deployment (advanced restraint system) driver and front passenger air bag modules. These vehicles are also equipped with driver and front passenger safety belt retractor pretensioners. These vehicles can also be equipped with optional side air curtains that deploy from the A-pillar to the C-pillar upon a side impact. Vehicles with optional side air curtains are also equipped with seat side air bag modules in the front seats.
Side air curtains deploy from the headliner, protecting the first and second row outboard occupants during a side impact. Seat side air bag modules deploy from the outboard front seat backrest upon a side impact. In addition, a front impact severity sensor is mounted to the lower radiator support, a seat position sensor is mounted to the driver seat and a usage detection switch is added to the front driver and passenger outboard buckles. If equipped with optional side air curtain modules and seat side air bag modules, there are an additional 4 side impact sensors.
Vehicles are also equipped with an occupant classification sensor (OCS) system as part of the front passenger seat. The OCS system includes 2 OCS rails and an OCS module.
Passenger Air Bag Deactivation (PAD) Indicator
The passenger air bag deactivation (PAD) indicator is a visual indicator used to inform the front seat occupants of the passenger air bag deactivation state. The PAD indicator is a stand-alone lamp installed into the vehicle instrument panel in a position visible to each front seat occupant.
The restraints control module (RCM) controls the state of the PAD indicator through a direct hardwire connection, based on information provided by the occupant classification sensor (OCS) system. The PAD indicator is lit to indicate the passenger air bag module is disabled. An exemption to this is when the front passenger seat is determined to be empty and passenger safety belt buckle unbuckled, and therefore indication of a deactivated passenger air bag module is not necessary. In all other cases, the PAD indicator is unlit when the passenger air bag module is enabled.
When the ignition switch is in the ON position, the PAD indicator prove-out period is initiated by the RCM. The RCM briefly activates the PAD indicator to prove-out the indicator function and verify to the front occupants correct functional operation of the PAD indicator.
The PAD indicator will be lit/unlit within 1.0 to 1.5 seconds of a change of state from the OCS system.
When an OCS system fault is present, the RCM defaults the passenger air bag module to the last valid state received from the OCS system until the ignition switch is turned OFF. If the OCS system fault is still present when the ignition switch is turned ON, the RCM defaults the passenger air bag module to enabled regardless of the size of occupant in the front passenger seat. The PAD indicator will be unlit. For information on the OCS system, refer to Occupant Classification Sensor System in this section.
The following table indicates the passenger air bag status and the PAD indicator status based the size of the front outboard passenger occupant.

Remove the rear weather stopping. Remove the two passenger side rear seat belt mounting bolts. Remove the upper and lower rear trim covers. Remove the passenger rear most trim panel. Remove the passenger trim panel Justin from of that. Remove the lines from the EVAP core from under the vehicle. Remove the several screws and nuts that hold the rear HVAC housing in place. Carefully swing the HVAC housing away from the side of the vehicle keeping in mind you will need to unplug a couple connectors and use caution not to pull out the heater hoses when doing this. Disassembly the housing and swap out the EVAP core. The rear lines disconnect towards the front of the vehicle about right under the passenger front seat. They will be held to the body with half a dozen fastners.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

1. Make sure you have the anti-theft codes for the radio and the navigation system, then write
down the frequencies for the preset buttons.
2. Tilt the steering wheel all the way up and telescope it all the way in.
3. '04-07 models passenger's seat: Carefully insert the tip of a small screwdriver (A) through
the hole in the back of the front seat belt lower anchor cover (B) and into the hole in the
front seat belt lower anchor (C). Unlock the lower anchor by pushing in on the screwdriver.
Remove the screwdriver, and then detach the front seat belt anchor plate (D) and anchor
cover from the lower anchor.4. Slide the seat all the way forward, then remove the seat track end covers from the back of both seat tracks.5. Slide the seat about half way to the rear so you can access the seat mounting bolts. If equipped with the driver's 8-way power seat, fully raise the seat.
6. If equipped with a side airbag, disconnect the negative cable from the battery, and wait at
least 3 minutes before removing the seat. 7. Remove the bolts securing the front seat. 8. Lift up the front seat, then detach the harness clip and disconnect the connector.
If equipped, the seat heater connector on the 2-way power seat and passenger's
manual seat. '04-07 models, disconnect the seat position sensor subharness connector on the
driver's manual height adjustable seat and the driver's 8-way power seat.
9. With the help of an assistant, carefully remove the front seat through the front door opening. 10. Install the seat in the reverse order of removal, and note these items:
Apply medium strength type liquid thread lock to the front seat mounting bolts
before reinstallation.
Make sure each connector is plugged in properly.
Tighten the seat mounting bolts to the specified torque in the sequence shown.
Slide the seat all the way back and tighten then slide it forward and
tighten Before attaching the lower anchor bolts, make sure there are no twists or kinks in
the seat belts. 04-07 models passenger's seat: The triangle marks on the anchor plate and
the lower anchor must face the same side. Insert the anchor plate into the lower
anchor, and make sure that it is locked securely. If equipped with a side airbag, reconnect the negative cable to the battery. Enter the anti-theft codes for the radio and navigation system, then enter the radio station presets. Reset the clock. Your all done. Drink a cold beverage and enjoy the rest of your weekend! hope this helps. Dave

The seats should have a couple of bolts one on each side of the car, they are on the inside where the front of the seat meets the floor, sometimes they are partially hidden as the seat cushioning drops down over them. Remove both the bolts and then pick the front of the seat up and slide the back forward then work the seat belts through the seat. The panel should just gently pry off, try one corner gently to get it started, if it doesn't act as if it wants to budge then stop and inquire more in depth information on it.

There are 2 fuse boxes, they are called Bussed Electrical Centers.
The front Bussed Electrical
Center (This is one fuse box) is located in
the front of the engine
compartment on the
passenger’s side. Lift the
cover to gain access

Rear Underseat Bussed Electrical Center (BEC)
The rear BEC is located
beneath the rear seat on the
driver’s side. The rear seat
cushion must be removed to
access the BEC. See
“Removing the Rear Seat
Cushion” in the Index.

SECTION 501-10: Seating 1998 Escort/Tracer Workshop Manual REMOVAL AND INSTALLATION Seat —Front Removal
NOTE: Driver side seat shown, passenger side seat similar.

1. Slide the seat to its rearward position.

1. Remove the front seat track to floor front bolts.

1. Slide the seat to the forward position.

1. Remove the front seat track to floor rear bolts.

1. Disconnect the safety belt warning indicator switch electrical connector.

1. Remove the front seat.

The battery is under the rear seat on the passengers side.To remove the seat bottom push in and up from the front of the seat.There will be 2 latches.One on the passengers side and one on the drivers side.There is also a seat heater connector on the passengers side so when you pull the seat up make sure and disconnect this connector before removing the seat.You will see the battery once you pull the seat up.Good luck.

Hi,

2001 Dodge Caravan Performance Features -3,301 cc 3.3 liters 6 V engine with 93 mm bore, 81 mm stroke, 9.3 compression ratio, overhead valve and two valves per cylinder
-Unleaded fuel
-Fuel economy EPA highway (l/100km): 9.8
-Multi-point injection fuel system
-Main 76 liter unleaded fuel tank
-Power: SAE and 134 kW , 180 HP @ 5,000 rpm; 210 ft lb , 285 Nm @ 4,000 rpm
2001 Dodge Caravan Handling & Driving Features -ABS
-Two disc brakes including two ventilated discs
-Spacesaver steel rim under body spare wheel
-Strut front suspension with stabilizer bar independent with coil springs , beam rear suspension with stabilizer bar rigid with leaf springs
2001 Dodge Caravan Exterior Features -Body side molding
-Front and rear body color bumpers
-Driver and passenger power heated black door mirrors
-External dimensions: overall length (mm): 4,803, overall width (mm): 1,996, overall height (mm): 1,750, wheelbase (mm): 2,878, front track (mm): 1,600, rear track (mm): 1,626 and curb to curb turning circle (mm): 11,460
-Complex surface lens halogen bulb headlights
-Double sliding minivan side door
-Remote control operation opening rear ¼ windows
-Metallic paint , gloss paint , pearl paint
-Fixed rear window
-Tinted glass on cabin, rear and side
-Weights: curb weight (kg) 1,842, gross trailer weight braked (kg) 907 and max legal load (kg) 772
-Windshield wipers with variable intermittent wipe
2001 Dodge Caravan Interior Features -Air conditioning with rear outlet
-Fixed mast antenna
-Manufacturer's own audio system
-Automatic drive indicator on dashboard
-Below seat storage under passenger seat
-Cargo capacity: all seats in place (liters): 433, all seats removed (liters): 4,154 and third row seats removed (liters): 1,291
-Clock
-Dashboard full console with open storage box
-Delayed/fade courtesy lights
-Cruise control
-Front seats, rear seats and 3rd row seats cup holders
-Door ajar warning
-Door pockets/bins for driver seat and passenger seat
-Floor covering: carpet in load area
-Driver and passenger front airbag
-Bucket seat
-3-point reel height adjustable front seat belts on driver seat and passenger seat
-Front seat center armrest
-Glove compartment
-Height adjustable two head restraints on front seats, rear seats and 3rd row seats
-Internal dimensions: front headroom (mm): 1,011, rear headroom (mm): 998, front hip room (mm): 1,440, rear hip room (mm): 1,722, front leg room (mm): 1,031, rear leg room (mm): 930, front shoulder room (mm): 1,588 and rear shoulder room (mm): 1,643
-Low fuel level warning
-Low washer fluid level warning
-Internal button power locks
-Power steering
-Front power windows with one one-touch
-Front reading lights
-3-point reel height adjustable rear seat belts on driver side and passenger side
-Bench one-piece two rear seats
-Rear view mirror
-Upgraded cloth/velour seat upholstery
-Seating: seven seats
-Six speakers
-Plastic steering wheel
-Tachometer
-3-point reel third row seat belts on driver side , 3-point reel third row seat belts on passenger side , lap static third row seat belts on center side
-Front facing bench removable one-piece third row seats with capacity three
-Driver and passenger vanity mirror
-Ventilation system with recirculation setting
Thanks.

HIYA!
All Equinoxes has yellow coloured wire harness to identify this as a air-bag system.
This yellow coloured wire 'system network' has connections in some areas...one is located at the front passenger's floor area close to the door (right-side corner area, just remove screw or clip and plastic trim part to gain access to see yellow wire there-it has socket plug connected with red clip-string to secure it) and another yellow wire is found between the front seats-you need to remove armrest, center console area and possible remove the front passenger seat to see yellow wire connect to black device underneath carpet in the middle.
Check to ensure the yellow wire sockets are plugged in properly, and not accidently cut or pulled off during your underseat repair.
In case your Equinox has roof side air-bag option, the yellow wire/sensor are located below the front seatbelt device inside the lower pillar frame area. (it's between the doors)
Hope this help you solve your repair task.